AVIMASTIC INTUMESCENT ACRYLIC SEALANT AVIMASTIC is an elastomeric intumescent sealant. It is a high solid water based acrylic, specially compounded to provide exceptional adhesive and elastomeric properties for a high fire stopping sealant requirement for sealing joint in walls, floors and ceiling, to seal around architraves and frames, to seal fire rated duct work. Properties Characteristics • • • • • Can be used to seal joints in floors, walls and ceilings Can be used to seal round door architraves and frames Can be used to seal fire rated duct work Joint movement capability +/- 10% Bonds to brick, plaster, concrete, wood, metal and painted surfaces Give up to 4 hours integrity A medium viscosity paste containing acrylic emulsion, inert fillers and fungicide. Can be used internally or externally. •   Fully tested to 4 hours fire protection using either mineral wool or PE backing rods. No smoke, halogen free NES 715 issue tested for low toxicity of 0.44 ATIV (Average Toxicity Index Value)        Maximum joint width - 35mm Optimumperformance depth to width ratio - 1 to 2 Colors Available - standard colors red, white, others available to special order Can be over painted Toxicity NES 715 issue 3, Average Toxicity Index Value – 0.44 Tack free time - 15-50 minutes depending on temperature/humidity. Thixotropic thorough curing - 20 days time at 20°C for 20mm depth Packing - 310 ml Cartridges Performance Tested at Warrington Fire Research to BS 476 Part 20, Class 1, Class O. Fire Integrity - 4 hours fire integrity Safety Benefits: • • • • • Benefits Legislation Compartment walls and floors must maintain the appropriate level of fire resistance as laid down by Building Regulations Approved Document B 1991. Movement joints in walls, floors and joints at the head of walls need a product that can provide movement and at the same time provide up to 4 hours integrity. Avimastic satisfies all these requirements. Manufactured under ISO 9001:2000 Quality System. Application One part intumescent acrylic sealant Swells in a fire to give a smoke and fire resistant seal Halogen and solvent free Resistant to fungus, mould Fire rated up to 4 hours (depending on joint design) Avimastic Acrylic Sealant is high quality fire rated sealant. All surfaces must be clean, dry and free from dirt, grease and loose particles remove nozzle and cut to the required diameter, cut off cartridge tip and screw on nozzle. Ensure that the sealant is forced into the joint so that full contact is made with joint surfaces. Use joint backing rod to control sealant depth and assist in correct joint design. Smooth with wet tooling knife. Surrounding areas may be masked off to protect / prevent contamination. Manufactured in Saudi Arabia by: Arabian Vermiculite Industries Sales Offices: DAMMAM P.O.Box 7137, Dammam 31462, Saudi Arabia Tel.: (03) 847-1450, Fax: (03) 847-1575 E-mail: [email protected] RIYADH JEDDAH P.O.Box 61531, Riyadh-11575, P.O.Box 110044, Jeddah 21361, Saudi Arabia Saudi Arabia Tel.: (01) 472-8119, Fax: (01) 478-4440 Tel.: (02) 674-3100, Fax: (02) 674-3035 Material Requirement: PREPARATION Use the following formula to determine number of cartridges required – Proper preparation is important to ensure the joint system performs to requirements. Gap Width (mm)XDepth (mm)X Total Length (mm) 310 = No of Cartridges The surface must be free from dust, loose particles, moisture, oils, grease and corrosion before commencing installation. Specification Avimastic has an excellent adhesion and doesn’t require any primer before use. “Install Avimastic (colour) fire seals in full accordance with manufacturer’s instructions. INSTALLATION INSTRUCTIONS Health and Safety It is recommended that joints should have a minimum width of 5mm. Keep out of reach of children Avoid contact with skin and eyes Wash hands after use Do not ingest For optimum performance ratio is 2:1 width:depth. A minimum depth of 10mm should be used. Safety Data Sheet available on request. Apply AVIMASTIC against a firm backing rod so that it is forced against the sides of the joint, to ensure good adhesion. The correct installation of the backing material enables the required shape and profile of the seal to be achieved. The Backing Rod should be oversized to match the joint width enabling it to resist movement during installation. Storage Store between 5°C and 25°C Shelf Life: 12 months Protect from frost. Maintenance: Routine inspection recommended to ensure no damage. No maintenance required after installation. Do not use none flexible material as backing rod such as polystyrene boards. Material Requirement: Avimastic is waterborne fire resistant acrylic gap mastic for use in structural, low-movement joints (movement ± 5%). INSTALLATION CHECK LIST • Determine the correct depth of seal required to achieve the fire rating. • Use fire rated backing rod oversize to joint to obtain correct seal profile. • Ensure that the contact faces are suitable for sealant application. • Ensure that the width of the joint is within the Product Specification. • Abrade all painted areas surfaces to form a key for Avimatic. • Ensure all contact areas are dry and free from any dirt and loose particles and contamination. Manufactured in Saudi Arabia by: Arabian Vermiculite Industries Sales Offices: DAMMAM P.O.Box 7137, Dammam 31462, Saudi Arabia Tel.: (03) 847-1450, Fax: (03) 847-1575 E-mail: [email protected] RIYADH JEDDAH P.O.Box 61531, Riyadh-11575, P.O.Box 110044, Jeddah 21361, Saudi Arabia Saudi Arabia Tel.: (01) 472-8119, Fax: (01) 478-4440 Tel.: (02) 674-3100, Fax: (02) 674-3035 Cut nozzle of cartridge. Use a cartridge gun to apply the Avimastic. Ensure that good contact is made with all surfaces and that the joint is filled to the required seal depth. Tool to a smooth finish immediately with a wet palette knife or spatula. Avimastic can be painted after full cure. Health and Safety: Material Safety Data Sheet is available upon request. Manufactured in Saudi Arabia by: Arabian Vermiculite Industries Sales Offices: DAMMAM P.O.Box 7137, Dammam 31462, Saudi Arabia Tel.: (03) 847-1450, Fax: (03) 847-1575 E-mail: [email protected] RIYADH JEDDAH P.O.Box 61531, Riyadh-11575, P.O.Box 110044, Jeddah 21361, Saudi Arabia Saudi Arabia Tel.: (01) 472-8119, Fax: (01) 478-4440 Tel.: (02) 674-3100, Fax: (02) 674-3035