BD2 + R24 BD2 + R24 TABELLA DI PERFORMANCE PERFORMANCES TABLE BD2 +R24 Reduction Ratio / Rapp. Riduzione 6,231:1 Min Max Nominal Displacement / Cilindrata Nominale Min Max 3000 1500 1000 750 2100 1000 750 550 1074 767 2162 1081 757 541 17.1 12.2 34.4 17.2 12.0 8.6 Displacement / Cilindrata [cc/rev] 3069 1535 Specific Torque / Coppia Specifica [Nm/bar] 48.9 24.4 Peak Pressure / Pressione di Picco [bar] 350 375 Max Torque / Max Coppia [Nm] 17100 8550 6000 4270 12900 6450 4500 3200 Max Speed / Massima Velocità [rpm] 130 260 320 350 160 290 320 350 Peak Power / Potenza di Picco [kW] 75 65 65 65 75 65 65 65 Approximative mass 200 [kg] Motor casing oil capacity 5,5 [l] Max casing Pressure 5 [bar] (peak) 1 [bar] (continuous) 100401.3P Note: For higher pressure please contact SAI Technical Department. Maximum speed to be revised according to distributor's and valves' flow capability. SAI Spa 41122 Modena Italia www.saispa.it e-mail [email protected] Massa approssimativoa 200 [kg] Capacità olio corpo motore 5,5 [l] Pressione max in carcassa 5 [bar] (picco) 1 [bar] (continuo) Nota: Per pressioni più elevate consultare l'Ufficio Tecnico SAI.Velocità massima da adattare alla portata del distributore e delle valvole. Provisional leaflets subjected to change without notice. All data are real and calculated according to existing project BD2 + R24 PRODUCT COMPONENTS - R24 Gearbox - BD2 Hydraulic motor series - Standard fitting with D40 distributor * FEATURES - Internal connection between case and return line allows the unit to be installed without drain line for system with max return pressure up to 15 bar - Suitable for special distributor blocks designed to include valve cartridges - Overall dimensions and weight lower than direct drive units - Available stainless steel sleeve on shaft seal easy to replace without disassembling the gearbox . - High radial load capability and long life bearing * Available also in the version with integrated valve block, see here below schema. Radial load [kN] . 100401.3P Load distance from mounting flange [mm] SAI Spa 41122 Modena Italia www.saispa.it e-mail [email protected] Provisional leaflets subjected to change without notice. All data are real and calculated according to existing project BD3 R20FA PROVISIONAL LEAFLET BD3 R20FA BD3 R20FA performances data R20FA Gearbox Ratio/Rapp Riduzione 1:5,6 Max Braking Torque 16000 [Nm] Nominal Displ./ Cilindrata Nominale Displacement/ cilindrata Specific Torque/ Coppia Specifica Peak Pressure/ Pressione di Picco Peak Torque/Coppia di Picco Max Speed(Off the Gearbox)/ Vel Max (Al Riduttore) Peak Power / Potenza Di Picco 070761.1P Approximative weight Motor casing oil capacity Gearbox casing oil capacity Max casing Pressure SAI Spa 41100 Modena Italia www.saispa.it e-mail [email protected] 185 4.5 3.5 5 1 3100 700 4100 950 5150 1200 [cc/rev] [Nm/bar] [bar] [Nm] [rpm] [kW] [kg] [lit] [lit] [bar] (peak) [bar] (continuous) 3091 711.2 4116 952 5135.2 1187.2 49.22 11.32 65.54 15.16 81.77 18.90 320 245 190 16000 16000 16000 100 100 100 95 85 95 85 95 85 Peso Approssimativo Capacità olio corpo motore Capacità olio carter riduttore Pressione max in carcassa 185 4.5 3.5 5 1 [kg] [lit] [lit] [bar] (picco) [bar] (continuo) Provisional leaflets subjected to change without notice. All data are real and calculated according to existing project BV1 D47PV+R13 BV1 D47PV+R13 TABELLA DI PERFORMANCE PERFORMANCES TABLE Max Min Max Min Max Min 1300 0 1500 200 1700 400 1277 0 1490 213 1703 426 3.4 27.1 6.8 [cc/rev] Displacement / Cilindrata 7:1 Reduction Ratio / Rapp. Riduzione [Nm/bar] Specific Torque / Coppia Specifica 20.3 0.0 23.7 [bar] 170 2 150 2 130 2 Peak Pressure / Pressione di Picco [bar] 350 3 300 3 260 3 Max Torque / Max Coppia [Nm] 7000 0 7000 1000 7000 0 Max Speed / Massima Velocità [rpm] 120 360 120 360 120 360 Peak Power / Potenza di Picco Continuous Output Torque [kW] 55 42 55 42 55 42 Pressure Rating 1 / Press. Nominale Coppia Continua in Uscita Peak Output Torque Coppia di Picco in Uscita Continuous Output Speet Velocità Continua in Uscita Approximative weight Peso approssimativo Motor casing oil capacity Capacità di olio corpo motore Gearbox casing oil capacity Capacità di olio riduttore 1 [Nm] 3500 [Nm] 7000 [rpm] 80 [kg] 60 Note: 1 Continuous or average working pressure should be chosen in function of the bearing lifetime. For lifetime calculation of motor bearings and for higher case pressure please consult SAI Tech. Dept. 1 [l] 1.5 [l] 3 La pressione continua o media di lavoro va determinata in funzione della vita dei cuscinetti. Per un calcolo di vita dei cuscinetti del motore e per pressioni più elevate in carcassa consultare l'Ufficio Tecnico SAI. 2-3 continuous 1 Max casing Pressure continuo [bar] peak 090926.2P picco SAI Spa 41122 Modena Italia www.saispa.it e-mail [email protected] 2-3 5 Pressione max in carcassa Pressure rating and peak pressure limitation due to continuos and peak output torque of the gearbox Pressione continua e di picco limitata per la coppia continua e massima del riduttore Provisional leaflets subjected to change without notice. All data are real and calculated according to existing project BV1 D47PV+R13 DIMENSIONI D’INGOMBRO DIMENSIONAL DRAWING . 090926.2P . SAI Spa 41122 Modena Italia www.saispa.it e-mail [email protected] Provisional leaflets subjected to change without notice. All data are real and calculated according to existing project GM05+F5+R03D GM05+F5+R03D TABELLA DI PERFORMANCE PERFORMANCES TABLE GM5+F5+R03D 4,28:1 R03D Gearbox Ratio / Rapp. Riduzione Nominal Displacement / Cilindrata Nominale 170 250 320 370 490 Total Displacement / Cilindrata Tot. [cc/rev] 167 253 317 368 492 552 Equivalent Specific Torque / Coppia Specifica Equivalente [Nm/bar] 2.66 4.02 5.04 5.86 7.83 8.79 450 450 425 400 350 300 235 200 210 Pressure Rating / Pressione Nominale [bar] Peak Pressure / Pressione di Picco [bar] Max Cont. Torque / Max Coppia Continua [Nm] 1350 Max Torque / Max Coppia [Nm] 2700 Max Speed (on gerabox) / Massima Velocità (all'uscita rid.) [rpm] Peak Power / Potenza di Picco [kW] 550 250 235 235 235 25 Approximative weight 45 [kg] Peso Approssimativo 45 [kg] Motor casing oil capacity 0.8 [lit] Capacità olio corpo motore 0.8 [lit] Gearbox oil capacity 0.8 [lit] Capacità olio riduttore 0.8 [lit] 1 [bar] (peak) 1 [bar] (picco) 5 [bar] (continuous) 5 [bar] (continuo) Max casing Pressure Pressione max in carcassa Note: Per pressioni più elevate consultare l'Ufficio Tecnico SAI Max speed is to be revised according to distributor's and valves' flow capability La velocità massima è da correggere in fuzione della portata del distributore e delle valvole 080893.1P Note: For higher pressure please consult SAI Tech. Dept. SAI Spa 41100 Modena Italia www.saispa.it e-mail [email protected] Provisional leaflets subjected to change without notice. All data are real and calculated according to existing project GM05+F5+R03D DIMENSIONI D’INGOMBRO DIMENSIONAL DRAWING . D504 Distributor with double overcentre valve and high pressure pilot line(C) Max flow 120 lit/min. Pilot ratio 10:1 Max pressure 265 bar. Pressure setting=1.3 x working pressure. Press. setting range 100 to 350 bar Back-pressure in port B may adversely affect operation of the valve. . Distributore con doppia valvola di bilanciamento e valvola di pilotaggio ad alta pressione(C). Portata max 120 lit/min. Rapporto di pilotaggio 10:1 Pressione max 265bar Pressione di taratura =1.3 x press.di lavoro. Gamma di taratura da 100 a 350 bar. Contropressione in port B può causare malfunzionamento della valvola. F5 HYDRAULIC NEGATIVE DISC BRAKE Il freno F5 è un freno di stazionamento o emergenza, idraulico negativo a dischi multipli a bagno di olio. I freni sono normalmente forniti con 2 molle a tazza. Pressione massima di pilotaggio 50 bar. Minima pressione di apertura 20bar. Coppia frenante 500Nm. For higher pilot pressures please contact SAI Tehnical. Office Per pressioni di pilotaggio maggiori contattare Ufficio Tecnico SAI 080893.1P F5 hydraulic negative disc brake operating in oil bath can be fitted between motor and gearbox. Tha brakes are normally supplied with 2 cup springs. Max. pilot pressure 50 bar. Minimum opening pressure 20 bar. Braking torque 500Nm. SAI Spa 41100 Modena Italia www.saispa.it e-mail [email protected] Provisional leaflets subjected to change without notice. All data are real and calculated according to existing project GM05+F5+R03D GEARBOX R03D RIDUTTORE R03D The gearbox R03D is an extremely compact one stage planetary reduction gearbox, designed to run silently, with a long lifetime and to require minimum maintenance. Riduttore planetario ad uno stadio di riduzione caratterizzato da ridotte dimensioni, funzionamento silenzioso, lunga durata e minime esigenze di manutenzione. Rapporto di riduzione 4.28:1 Ratio 4.28:1 n 2xh Mc= [Nm] 10000 1920 20000 1700 30000 1450 40000 1280 Maximum torque Coppia massima This is the maximum output torque that the planetar y unit can transmit in a short time without causing damage to the internal cmponents and structure. This value must be considered as the maximum output torque due to working or starting peaks and never as the continnuous working torque. E’ il valora massimo di coppia che il riduttore può trasmettere per breve tempo senza che si verifichino danneggiamenti ai suoi componenti interni ed alla sua struttura.Tale valore deve essere considerato come una coppia massima dovuta a picchi o spunti di avviamento e mai come coppia massima. La coppia massima del gruppo è: 2700Nm The max torque for the unit is: 2700Nm Product components - GM05A Hydraulic motor with alluminium casing - D504 Distributor (also available with different distributor covers) - F5 Hydraulic-negative-disc parking/emergency brake. - R03D Gearbox Features - Case peak pressure 20 bar. The unit can be installed without drain line for systems with max return pressure up to 10 bar (connecting the case to the return line) - Suitable for special distributor blocks designed to include valve cartridges (D504 or other available) - Overall dimensions and weigh lower than direct units 080893.1P - High radial load capability and long life bearings. Radial load up tp 15000N cont., 25000N peak. SAI Spa 41100 Modena Italia www.saispa.it e-mail [email protected] Provisional leaflets subjected to change without notice. All data are real and calculated according to existing project GM05A D504 MOTOR PLUS F5 BRAKE PLUS R03C GEARBOX MOTORE GM05A D504 CON FRENO F5 CON RIDUTTORE R03C GM05A+F5+R03C PERFORMANCES DATA Nominal displacement/cilindrata nominale cm3/rev 170 250 320 380 470 550 171 257 321 385 471 556 Total displ. Cilindrata totale Reduction ratio Rapporto di riduzione Specific torque Coppia specifica Nm/bar 2.72 4.09 5.11 6.13 7.49 8.86 Pressure rating Pressione in continuo bar 250 250 250 250 250 220 Peak pressure Pressione di picco bar 450 450 425 400 350 300 Cont. Output speed Velocità continua rpm 165 165 165 165 150 150 Peak torque Coppia di picco Nm Peak speed Velocità di picco rpm 235 235 235 235 200 200 Peak Power Potenza di picco kW 25 25 25 25 25 25 4,28:1 Approximate weight: 45 kg (GM05A-Alluminium) Drive unit casing oil capacity: 1.6 l Continuous casing pressure: 5 bar Motor casing pressure peak: 10 bar 080876.2P For higher pressure pls consult SAI tech. Dept. 2700 Peso approssimato: Capacità olio del gruppo : Pressione in carcassa in continuo: Pressione in carcassa di picco : 45 kg 1.6 l 5 bar 10 bar Per pressione più elevate consultare l’uff. Tecnico SAI Max.speed to be revised according to distributor’s and valves’ velocità massima da adattare alla portata del distributore flow capability. e delle valvole. SAI Spa 41100 Modena Italia www.saispa.it e-mail [email protected] Provisional leaflets subjected to change without notice. All data are real and calculated according to existing project GM05A D504+F5+R03C D504 Distributor with doubl e overcentre valve and high pressure pilot line(C) Max flow 120lit/min. Pilot ratio 10:1 Max pressure 265 bar. Pressure setting=1.3 x working pressure. Press. setting range 100 to 350 bar Back-pressure in port B may adversely affect operation of the valve. Distributore con doppia valvola di bilanciamento e valvola di pilotaggio ad alta pressione(C). Portata max 120lit/min. Rapporto di pilotaggio 10:1 Pressione max 265bar Pressione di taratura =1.3 x press.di lavoro. Gamma di taratura da 100 a 350 bar. Contropressione in port B può causare malfunzionamento della valvola. F5 HYDRAULIC NEGATIVE DISC BRAKE F5 hydraulic negative disc brake operating in oil bath can be fitted between motor and gearbox. Tha brakes are normally supplied with 2 cup springs. Max. pilot pressure 50 bar. Minimum opening pressure 20 bar. Braking torque 500Nm. 080876.2P For higher pilot pressures please contact SAI Tehnical. Office SAI Spa 41100 Modena Italia www.saispa.it e-mail [email protected] Il freno F5 è un freno di stazionamento o emergenza, idraulico negativo a dischi multipli a bagno di olio. I freni sono normalmente forniti con 2 molle a tazza. Pressione massima di pilotaggio 50 bar. Minima pressione di apertura 20bar. Coppia frenante 500Nm. Per pressioni di pilotaggio maggiori contattare Ufficio Tecnico SAI Provisional leaflets subjected to change without notice. All data are real and calculated according to existing project GM05A D504+F5+R03C RIDUTTORE R03C GEARBOX R03C The gearbox R03C is an extremely compact one stage planetary reduction gearbox, designed to run silently, with a long lifetime and to require minimum maintenance (Ratio 4.28:1) Riduttore planetario ad uno stadio di riduzione caratterizzato da ridotte dimensioni, funzionamento silenzioso, lunga durata e minime esigenze di manutenzione. Rapporto di riduzione 4.28:1 n2xh Mc= [Nm] 10000 1920 20000 1700 30000 1450 40000 1280 Coppia massima Maximum torque This is the maximum output torque that the planetary unit can transmit in a short time without causing damage to the internal cmponents and structure. This value must be considered as the maximum output torque due to working or starting peaks and never as the continnuous working torque. E’ il valora massimo di coppia che il riduttore può trasmettere per breve tempo senza che si verifichino danneggiamenti ai suoi componenti interni ed alla sua struttura.Tale valore deve essere considerato come una coppia massima dovuta a picchi o spunti di avviamento e mai come coppia massima. La coppia massima del gruppo è:2700Nm The max torque for the unit is:2700Nm Product components GM05A Hydraulic motor with alluminium casing D504 distributor (available with different distributor covers) F5 hydraulic-negative-disc parking/emergency brake. R03C gearbox Features •Case peak pressure 20 bar the unit can be installed without drain line for systems with max return pressure up to 10 bar (connecting the case to the return line) •Suitable for special distributor blocks designed to include valve cartridges( D504 or other available) •Overall dimensions and weigh lower than direct units 080876.2P •High radial load capability and long life bearings. Radial load up tp 15000N cont. 25000N peak. SAI Spa 41100 Modena Italia www.saispa.it e-mail [email protected] Provisional leaflets subjected to change without notice. All data are real and calculated according to existing project GM1+GR324 GM1+GR324 TABELLA DI PERFORMANCE PERFORMANCES TABLE GM1+GR324 43.617:1 Reduction Ratio / Rapp. Riduzione Nominal Displacement / Cilindrata Nominale 4300 5600 6700 7500 8800 9600 10600 Displacement / Cilindrata [cc/rev] 4297 5613 6714 7504 8770 9669 10611 Specific Torque / Coppia Specifica [Nm/bar] 68.4 89.3 106.9 119.4 139.6 153.9 168.9 Peak Pressure / Pressione di Picco [bar] 260* 200* 170* 150* 130* 115* 100* Max Torque / Max Coppia [Nm] Max Speed / Massima Velocità [rpm] 15 15 Peak Power / Potenza di Picco [kW] 18000 25 25 25 20 20 48 Reduction Ratio / Rapp. Riduzione 31.155:1 Nominal Displacement / Cilindrata Nominale 6300 6900 7600 9000 Displacement / Cilindrata [cc/rev] 3069 4009 4796 5360 6264 6906 7580 9020 9788 Specific Torque* / Coppia Specifica* [Nm/bar] 48.9 63.8 76.3 85.3 99.7 109.9 120.6 143.6 155.8 370* 280* 235* 210* 180* 160* 150* 125* 115* 25 25 20 20 Peak Pressure / Pressione di Picco [bar] Max Torque / Max Coppia [Nm] Max Speed / Massima Velocità [rpm] Peak Power / Potenza di Picco [kW] 3100 4000 4800 5400 * Peak pressure limitation due to output toque limit of 18000 Nm Approximative weight M otor casing oil capacity Gearbox oil capacity M ax casing Pressure 9800 18000 30 30 30 30 25 48 *Pressione di picco limitata per la massima coppia ammissibile di 18000 Nm 190 [kg] Peso Approssimativo 1 [l] Capacità olio corpo motore 3,5 [l] Capacità olio riduttore 1 [bar] (peak) 5 [bar] (continuous) Pressione max in carcassa 190 [kg] 1 [l] 3,5 [l] 1 [bar] (picco) 5 [bar] (continuo) Note: Per pressioni più elevate consultare l'Ufficio Tecnico SAI Max speed is to be revised according to distributor's and valves' flow capability La velocità massima è da correggere in fuzione della portata del distributore e delle valvole 080883.1P Note: For higher pressure please consult SAI Tech. Dept. SAI Spa 41100 Modena Italia www.saispa.it e-mail [email protected] Provisional leaflets subjected to change without notice. All data are real and calculated according to existing project GM1+GR324 DIMENSIONI D’INGOMBRO DIMENSIONAL DRAWING . PRODUCT COMPONENTS 080883.1P - GR324 Gearbox - GM1 Hydraulic motor serie - Standard fitting with D40 SAI Spa 41100 Modena Italia www.saispa.it e-mail [email protected] Provisional leaflets subjected to change without notice. All data are real and calculated according to existing project GM1+GR328 GM1+GR328 TABELLA DI PERFORMANCE PERFORMANCES TABLE GM1+GR328 30.8:1 Reduction Ratio / Rapp. Riduzione Nominal Displacement / Cilindrata Nominale 3000 4000 4700 5300 6200 6800 7500 8900 Displacement / Cilindrata [cc/rev] 3034 3963 4741 5299 6193 6827 7493 8917 9700 9676 Specific Torque / Coppia Specifica [Nm/bar] 48.3 63.1 75.5 84.3 98.6 108.7 119.3 141.9 154.0 Peak Pressure / Pressione di Picco [bar] 425 400 370* 330* 285* 260* 235* 200* 180* Max Torque / Max Coppia [Nm] 20500 25200 28000 28000 28000 28000 28000 28000 28000 Max Speed / Massima Velocità [rpm] 30 30 30 30 25 25 25 20 20 Peak Power / Potenza di Picco [kW] 6400 6900 48 Reduction Ratio / Rapp. Riduzione 22:1 Nominal Displacement / Cilindrata Nominale 2200 2800 3400 3800 4400 4900 5300 Displacement / Cilindrata [cc/rev] 2167 2831 3387 3785 4423 4877 5352 6370 6912 Specific Torque* / Coppia Specifica* [Nm/bar] 34.5 45.1 53.9 60.2 70.4 77.6 85.2 101.4 110.0 Peak Pressure / Pressione di Picco [bar] 425 400 400 375 350 350 330* 275* 255* Max Torque / Max Coppia [Nm] 14660 18000 21560 22590 26640 27170 28000 28000 28000 Max Speed / Massima Velocità [rpm] 45 45 45 40 40 30 30 30 30 Peak Power / Potenza di Picco [kW] 48 * Peak pressure limitation due to output toque limit of 28000 Nm Approximative weight Motor casing oil capacity Gearbox oil capacity Max casing Pressure *Pressione di picco limitata per la massima coppia ammissibile di 28000 Nm 200 [kg] Peso Approssimativo 1 [lit] Capacità olio corpo motore 3,5 [lit] Capacità olio riduttore 1 [bar] (peak) 5 [bar] (continuous) Pressione max in carcassa 200 [kg] 1 [lit] 3,5 [lit] 1 [bar] (picco) 5 [bar] (continuo) Note: Per pressioni più elevate consultare l'Ufficio Tecnico SAI Max speed is to be revised according to distributor's and valves' flow capability La velocità massima è da correggere in fuzione della portata del distributore e delle valvole 080882.2P Note: For higher pressure please consult SAI Tech. Dept. SAI Spa 41122 Modena Italia www.saispa.it e-mail [email protected] Provisional leaflets subjected to change without notice. All data are real and calculated according to existing project GM1+GR328 DIMENSIONI D’INGOMBRO DIMENSIONAL DRAWING . . PRODUCT COMPONENTS 080882.2P - GR328 Gearbox - GM1 Hydraulic motor serie - Standard fitting with D40 SAI Spa 41122 Modena Italia www.saispa.it e-mail [email protected] Provisional leaflets subjected to change without notice. All data are real and calculated according to existing project GM2 / GM3A + R24 GM2 / GM3A + R24 TABELLA DI PERFORMANCE PERFORMANCES TABLE GM2 / GM3A+ R24 6,231:1 Reduction Ratio / Rapp. Riduzione Motor model GM2 Nominal Displacement / Cilindrata Nominale GM3A 2700 3000 3500 3900 4300 5000 Displacement / Cilindrata [cc/rev] 2647 3069 3524 3885 4297 4933 Specific Torque / Coppia Specifica [Nm/bar] 42.1 48.9 56.1 61.8 68.4 78.5 Peak Pressure / Pressione di Picco [bar] 350 350 300 280 260 * 230 * Max Torque / Max Coppia [Nm] 14700 17000 16800 17300 18000 18000 Max Speed / Massima Velocità [rpm] 120 110 110 100 80 Peak Power / Potenza di Picco [kW] 59 80 80 * Peak pressure limitation due to output toque limit of 18000 Nm * Pressione di picco limitata per la massima coppia ammissibile di 18000 Nm Approximative mass Motor casing oil capacity 120 - 160 [kg] 2 - 4,5 [l] Max casing Pressure 5 [bar] (peak) 1 [bar] (continuous) 100407.5P Note: For higher pressure please contact SAI Technical Department. Maximum speed to be revised according to distributor's and valves' flow capability. SAI Spa 41122 Modena Italia www.saispa.it e-mail [email protected] Massa approssimativoa Capacità olio corpo motore Pressione max in carcassa 120 - 160 [kg] 2 - 4,5 [l] 5 [bar] (picco) 1 [bar] (continuo) Nota: Per pressioni più elevate consultare l'Ufficio Tecnico SAI.Velocità massima da adattare alla portata del distributore e delle valvole. Provisional leaflets subjected to change without notice. All data are real and calculated according to existing project GM2 / GM3A + R24 PRODUCT COMPONENTS - R24 Gearbox - GM2 / GM3A Hydraulic motor series - Standard fitting with D40 distributor * FEATURES - Internal connection between case and return line allows the unit to be installed without drain line for system with max return pressure up to 25 bar - Stainless steel sleeve on shaft seal easy to replace without disassemble the gearbox - High radial load capability and long life bearing - Lighter than direct drive motor . * Available also in the version with integrated valve block, see here below schema. Radial load [kN] . 100407.5P Load distance from mounting flange [mm] SAI Spa 41122 Modena Italia www.saispa.it e-mail [email protected] Provisional leaflets subjected to change without notice. All data are real and calculated according to existing project GM2+R20FA / R21 GM2+R20FA / R21 TABELLA DI PERFORMANCE PERFORMANCES TABLE GM2+R20FA / R21 R20FA & R21 Reduction Ratio / Rapp. Riduzione 5,6:1 Nominal Displacement / Cilindrata Nominale 1100 1400 1700 1900 2400 2800 3200 3500 Displacement / Cilindrata [cc/rev] 1078 1407 1703 1943 2379 2759 3167 3491 55.6 Specific Torque / Coppia Specifica [Nm/bar] 17.2 22.4 27.1 30.9 37.9 43.9 50.4 Peak Pressure / Pressione di Picco [bar] 425 425 400 375 350 350 300 280 Max Torque / Max Coppia [Nm] 7300 9500 10900 11600 13200 15400 15100 15600 Max Speed / Massima Velocità [rpm] 140 140 130 130 130 125 125 115 Peak Power / Potenza di Picco [kW] 59 145 -313 [kg] 2 [l] Capacità olio corpo motore R20FA Gearbox oil capacity 3.5 [l] R21 Gearbox oil capacity 2.2 [l] 5 [bar] (peak) 1 [bar] (continuous) Approximative mass Motor casing oil capacity Max casing Pressure Massa approssimativa 145 -313 [kg] 2 [l] Capacità olio riduttore R20FA 3.5 [l] Capacità olio riduttore R21 2.2 [l] 5 [bar] (picco) 1 [bar] (continuo) Pressione max in carcassa Note: Nota: For higgher presure please contact SAI Technical Department. Per pressioni più elevate consultare l'Ufficio Tecnico SAI. 100891.2 Max speed is to be revised according to distributor's and valves' flow capability. For higher speed please contact SAI Technical Department. SAI Spa 41122 Modena Italia www.saispa.it e-mail [email protected] La velocità massima è da correggere in funzione della portata del distributore e delle valvole. Per maggiori velocità contattare l'Ufficio Tecnico SAI. Provisional leaflets subjected to change without notice. All data are real and calculated according to existing project GM2+R20FA / R21 DIMENSIONI D’INGOMBRO DIMENSIONAL DRAWING 100891.2 PRODUCT COMPONENTS - R20FA gearbox and brake or R21 gearbox - Riduttore e freno R20FA o riduttore R21 - GM2 hydraulic motor serie - Motore idraulico della serie GM2 - Standard fitting with D40 distributor - Distributore standard D40 SAI Spa 41122 Modena Italia www.saispa.it e-mail [email protected] Provisional leaflets subjected to change without notice. All data are real and calculated according to existing project GM2+R20FA / R21 VITA CUSCINETTI BEARINGS LIFETIME . With the graph given it is possible to find the maximum alloweble radial load on the shaft in two typical positions (A and B) for various lifetime requirements and operating speed. Please contact SAI Thecnical Department for a lifetime calculation of the motor. Il grafico riportato permette di valutare il massimo carico radiale ammissibile applicato in due posizioni tipiche (A e B) per diverse durate dei cuscinetti e velocità di funzionamento. Per un calcolo di vita del motore contattare l’Ufficio Tecnico SAI. HYDRAULIC NEGATIVE DISC BRAKE Il freno dell’unità R20FA è un freno di stazionamento o emergenza idraulico negativo a dischi multipli in bagno d’olio. Maximum pilot pressure: 50 bar Minimum opening pressure: 20 bar Braking torque: 16000 Nm Pressione massima di pilotaggio: 50 bar Minima pressione di apertura: 20 bar Coppia frenante: 16000 Nm 100891.2 An hydraulic negative disc brake operating in oil bath is fitted between motor and R20 FA gearbox. SAI Spa 41122 Modena Italia www.saispa.it e-mail [email protected] Provisional leaflets subjected to change without notice. All data are real and calculated according to existing project GM3 +R22RFA GM3 R22RFA GM 3 R22RFA 5000 Reduction Ratio / Rapp. Riduzione 5,6:1 [cc/rev] 4888 [Nm/bar] 77,8 Pressure Rating / Pressione Nominale [bar] 220 Peak Pressure / Pressione di Picco [bar] 250 Max Torque / Max Coppia [Nm] 19000 Max Speed / Massima Velocità [rpm] 85 Peak Power / Potenza di Picco [kW] 80 Displacement / Cilindrata Specific Torque / Coppia Specifica Approximative weight Approximative oil capacity Max casing Pressure Oil type 2 86 [kg] motor 4,5 [l] gearbox 3,5 [l] continuous 1 [bar] peak 5 motor gearbox Peso approssimativo 86 [kg] Capacità di olio approssimativa motore 4,5 [l] Pressione max in carcassa [bar] ISO 46 SAE 90 EP Tipo di Olio 2 riduttore 3,5 [l] continuo 1 [bar] picco 5 [bar] motore ISO 46 riduttore SAE 90 EP Note: 1) La pressione continua o media di lavoro va determinata in funzione della vita dei cuscinetti. Per un calcolo di vita dei cuscinetti del motore consultare l'Ufficio Tecnico SAI. 2) For higher case pressure please consult SAI Tech. Dept. 2 )Per pressioni più elevate in carcassa consultare l'Ufficio Tecnico SAI 090936.1P Note: 1) Continuous or average work ing pressure should be chosen in function of the bearing lifetime. For lifetime calculation of motor bearings please consult SAI Tech. Dept. SAI Spa 41122 Modena Italia www.saispa.it e-mail [email protected] Provisional leaflets subjected to change without notice. All data are real and calculated according to existing project GM3 +R22RFA DIMENSIONI D’INGOMBRO DIMENSIONAL DRAWING APPROVED APPLICATIONS PARAMETERS M ax Flow / Portata M assima Relief Setting Pressure / Impostazione Sovrapressione Continuous Pressure / Pressione Continua 090936.1P CALETTATURE SPLINE DATA SAI Spa 41122 Modena Italia Www.saispa.it e-mail [email protected] [l/min] 130 [M pa] 21 [bar] 210 [M pa] 18 [bar] 180 82 UNI 220 (B10X82X88 DIN 5462) d1 Ø82.0 d2 Ø88.0 A Ø12.0 d3 Ø82.0 d4 Ø88.0 B Ø12.0 +0.035 +0 +0.540 +0 +0.043 +0.016 -0.012 -0.034 -0.012 -0.034 -0.016 -0.034 H7 H11 F7 g6 d11 f7 Provisional leaflets subjected to change without notice. All data are real and calculated according to existing project GM5+R28 GM5 MOTOR PLUS R28 GEARBOX, 1:4.4 RATIO MOTORE GM5 CON RIDUTTORE R28, RAPPORTO DI RIDUZIONE 1:4.4 Nominal displacement/Cilindrata nominale Diplacement/Cilindrata Equivalent specific torque/Coppia Specifica Peak pressure/pressione di picco Max continuous torque/Coppia max in continuo Max torque at max press/Coppia max alla press max Max speed/ velocità massima Peak power/potenza di picco Approximate weight: Motor casing oil capacity: Max. casing pressure: 2300 370 Kg 10 lt 1 bar continuous 5 Bar Peak 070759.1P for higher pressure pls consult SAI tech. Dept. Max.speed to be revised according to distributor’s and valves’ flow capability. SAI Spa 41100 Modena Italia www.saispa.it e-mail [email protected] 3000 cc/rev 2314 2899 Nm/bar 36.83 46.14 bar 350 350 Nm 9207 11535 Nm 12890 16149 rpm 70 60 kW 120 120 3500 3550.8 56.51 350 14128 19779 50 120 4600 5200 5900 6500 7200 8000 8850 4571 5214 5896 6432 7186 7990 8830 72.75 82.98 93.84 102.37 114.37 127.16 140.53 300 275 250 250 220 200 200 18187 20746 21583 22521 23446 24161 25296 21825 22820 23459 25592 25161 25433 28107 45 40 40 35 35 35 30 120 120 120 120 120 120 120 Peso approssimato: Capacità olio del corpo motore: Max.pressione in carcassa: 370 Kg 10 lt 1 bar Continuo 5 bar Picco Per pressione più elevate consultare l’uff. Tecnico SAI Velocità massima da adattare alla portata del distributore e delle valvole. Provisional leaflets subjected to change without notice. All data are real and calculated according to existing project GM5+R28 DIMENSIONAL DRAWING 618.5 571.5 363 229 GM5 BEARINGS LIFETIME L10 Bearing Life, 3 mil rev L10 Bearing Life, 5 mil rev Max Peakt load on shaft 1 % of time L10 Bearing Life, 10 mil rev Max intermittent load on shaft 10 % of time Max continuous load on shaft 070759.1P Note: Radial load only for male shaft SAI Spa 41100 Modena Italia www.saispa.it e-mail [email protected] Provisional leaflets subjected to change without notice. All data are real and calculated according to existing project $%&&'()*( +, ()*( +,$%& !"! " #" ! " # !"! " #" $%&&'()*( +, ()*( +,$%& !"! " #" ! " # $% !"! " #" $%&&'()*( +, ()*( +,$%& !"! " #" !"! " #"
© Copyright 2024 Paperzz