FRM093E000.OTT Manuale connessioni Weintek verso PLC Elsist ELSIST S.r.l. Sistemi in elettronica Via G. Brodolini, 15 (Z.I.) 15033 CASALE M.TO ITALY Internet: http://www.elsist.it Email: [email protected] TEL. (39)-0142-451987 FAX (39)-0142-451988 INDICE 1ELSIST MODBUS RTU/ASCII............................................................................................................................... 2 1.1HMI Setting:..................................................................................................................................................... 2 1.2PLC Setting...................................................................................................................................................... 2 1.3Device address................................................................................................................................................ 2 1.4Wiring Diagrams.............................................................................................................................................. 2 2ELSIST TCP/IP...................................................................................................................................................... 6 2.1HMI Setting:..................................................................................................................................................... 6 2.2PLC Setting...................................................................................................................................................... 6 2.3Device address................................................................................................................................................ 6 2.4Wiring Diagrams.............................................................................................................................................. 6 MNL178B100 Pag. 1/6 Manuale connessioni Weintek verso PLC Elsist 1 ELSIST MODBUS RTU/ASCII Supported devices: SlimLine & Netsyst controllers RS232/485 Website: www.elsist.it 1.1 HMI SETTING: Parameters PLC type PLC I/F Baud rate Data bits Parity Stop bits PLC sta. nr 1.2 Recommended SlimLine/Netsyst III RTU RS232/RS485 115200 8 Even 1 1 PLC SETTING Communication mode 1.3 Options Notes SlimLine/Netsyst III RTU/ASCII RS232/RS485 9600/19200/38400/57600/115200 7,8 Even, Odd, None 1, 2 0-254 (255 Broadcast) Modbus RTU (ASCII protocol option) DEVICE ADDRESS Bit/Word Device type Format Range B %MX DDDDD 0 - 65535 B %MW_Bit DDDDDdd 000 - 6553515 W %MW DDDDD 0 - 65535 1.4 Memo 0x01 Read coil 0x05 write single coil 0x03 Read holding register 0x06 write single register 0x03 Read holding register 0x10 write multiple registers WIRING DIAGRAMS Elsist SlimLine/Netsyst controllers Modbus RTU/ASCII eMT3000 series COM1 RS232 9P D-Sub Female 2 RX 3 TX 5 GND COM3 RS232 9P D-Sub Female 8 RX 7 TX 5 GND COMx RS232 RJ45 Male 6 TXD 5 RXD 4 GND CMT/mTV series COM1 RS232 9P D-Sub Female 2 RX 3 TX 5 GND MNL178B100 COMx RS232 RJ45 Male 6 TXD 5 RXD 4 GND Pag. 2/6 Manuale connessioni Weintek verso PLC Elsist MT8000iE series (except MT8050iE) COM1 RS232 9P D-Sub Female 2 RX 3 TX 5 GND COMx RS232 RJ45 Male 6 TXD 5 RXD 4 GND MT6050/8050 iP series and iE Series COM1 RS232 9P D-Sub Female 9 RX 6 TX 5 GND COMx RS232 RJ45 Male 6 TXD 5 RXD 4 GND eMT3000 series COM1 RS485 2W 9P D-Sub Male 1 Data2 Data+ 5 GND COM3 RS485 2W 9P D-Sub Female 6 Data9 Data+ 5 GND RS485 2W 3-Way TB 2 D1 D+ 3 GND 1 MNL178B100 3 Pag. 3/6 Manuale connessioni Weintek verso PLC Elsist CMT/mTV series COM2 RS485 2W 9P D-Sub Female 7 Data6 Data+ 5 GND COM3 RS485 2W 9P D-Sub Female 4 Data1 Data+ 5 GND RS485 2W 3-Way TB 2 D1 D+ 3 GND 1 3 MT8000iE series COM1 RS485 2W 9P D-Sub Female 1 Data2 Data+ 5 GND COM3 RS485 2W 9P D-Sub Female 7 Data8 Data+ 9 GND RS485 2W 3-Way TB 2 D1 D+ 3 GND 1 3 MT6050/8050iP series COM1 RS485 2W 9P D-Sub Female 1 Data2 Data+ 5 GND COM3 RS485 2W 9P D-Sub Female 7 Data8 Data+ 5 GND RS485 2W 3-Way TB 2 D1 D+ 3 GND 1 MNL178B100 3 Pag. 4/6 Manuale connessioni Weintek verso PLC Elsist 2 ELSIST TCP/IP Supported devices: SlimLine & Netsyst controllers Ethernet TCP/IP Website: www.elsist.it 2.1 HMI SETTING: Parameters PLC type PLC I/F Port no. PLC sta. nr 2.2 Recommended SlimLine/Netsyst III Eth Ethernet 502 1 Notes 0-254 (255 Broadcast) PLC SETTING Communication mode 2.3 Options Modbus TCP/IP DEVICE ADDRESS Bit/Word Device type Format Range B %MX DDDDD 0 - 65535 B %MW_Bit DDDDDdd 000 - 6553515 W %MW DDDDD 0 - 65535 2.4 Memo 0x01 Read coil 0x05 write single coil 0x03 Read holding register 0x06 write single register 0x03 Read holding register 0x10 write multiple registers WIRING DIAGRAMS Direct connection (crossover cable) HMI RJ45 Male 1 TX+ 2 TX3 RX+ 4 BD4+ 5 BD46 RX7 BD3+ 8 BD3- MNL178B100 Wire color White/Orange Orange White/Green Blue White/Blue Green White/Brown Brown PLC RJ45 Male 3 RX+ 6 RX1 TX+ 4 Not Used 5 Not Used 2 TX7 Not Used 8 Not Used Pag. 5/6 Manuale connessioni Weintek verso PLC Elsist Through a hub/switch (pin-to-pin cable) HMI RJ45 Male 1 TX+ 2 TX3 RX+ 4 BD4+ 5 BD46 RX7 BD3+ 8 BD3- MNL178B100 Wire color (T568B) White/Orange Orange White/Green Blue White/Blue Green White/Brown Brown PLC RJ45 Male 1 TX+ 2 TX3 RX+ 4 Not Used 5 Not Used 6 RX7 Not Used 8 Not Used Pag. 6/6
© Copyright 2024 Paperzz
