MIC-­L/H
Feed Throat Tenperature Controller for Molding Machine
Summary
MIC-L
MIC is the cooling unit for material port of injection-­ molding machine which realized stable temperature control and high safety. The cooling water connection of primary side is unnecessary in the air-­cooled type which takes utility into consideration.
Temp Display/ Setting: Temp Controller: Features
The cooling water is unnecessary for air-­cooling type. The water supply utility can be removed and the energy saving is possible. Moreover, equipment itself is designed for energy saving.
Heating & Cooling PID Control
K
Input: Energy Saving
Digital Display/ Setting
Memory: SV1 SV2
Timer: 0 99hrs. 59min.(Turns ON After Setting)
7 Segments Indication:
(Cord Indication)
Operation Status, Alarm
(Reverse Phase, Insufficient Water, Overwork of Pump,
Overheating, Under Heating, Sensor Failure)
Stabilization of molding quality
Quiet noise and without water leakage trouble
There is not water leakage for using a canned pump. Also, there is a little equipment noise.
Stable temperature control precision
The material biting insert becomes improving when making the material inlet temperature for injection machine be stable and the molding quality is stable.
In precise molding, the material inlet temperature affects to material measuring precision. And the material is PA, LCP, etc.
It is possible to perform software control for cooling control with air-­cooling.
Compact
Setup in the injection machine is easy because the mechanism is simple and compact.
In case of the small mold, it is possible to using as the mold temperature controller. In the area of general mold temperatures in range of 60°C~70°C, demonstrates capable cooling functions
It doesn't fit the thin mold of cooling pipe because the drain pressure is low. Also, it isn't possible to cool less than the room temperature. Installs to low place of equipment ambient temperature.
Pump Performance Curves
9
Lift 8
7
6
60Hz
5
New patent application about the cooling method for air-­cooling: Japan 1
50Hz
4
3
Model
Medium
Clamp Force for Injection-­Molding Machine
MIC-L
MIC-H
Cooling Type (Ambient Temperature +10~90°C)
2
1
0
10
20
Flow Rate (L/min)
30
40
Primary side water supply is unnecessary! Without Water Supply
Mizuirazu (Non-­Water)
Supply the circulation medium
(Clean water With anti-­rust) only once.
Hopper on Injection-­Moldeing Machine
MIC-­L/H Feed Throat Tenperature Controller for Molding Machine
Constant supply is unnecessary to clean cooling tower water, etc.
Cylinder Section
Outer Dimension
MIC-­L/H
D
Unit:mm
D1
W
D2
Temperature Controller
MIC-L/H
Cleaning Tower
H
Standard Specifications
Unit
MIC-L
MIC-H
V
Voltage
Apparent Power
VA
Breaker Capacity
A
1Phase
Operational Temperature Range
Medium
Equipment Ambient Temperature+10
Clean Water
90
Antirust Water
Control Temperature-­Ambient Temperature
Cooling Capacity
kW
kW
kW
kW
kW
kW
Heater
kW
Capacity
Pump
Maximum Flow Rate
Cooling Fan
Temperature Controller
Output
kW
Output
W
Temperature Sensing Element
Heat Exchanger
Aluminum
Material
Volume
L
Medium Level Low/Overheat Alarm(H Type Only)
Alarm Output
Dry Breaker Points
Pipe Diameter
Medium Feed Port
Medium Return Port
Drain Port
Medium Refueling Port
Product Weight
kg
Options
Standard Hose Set
NOTE
Leakage Breaker
General Alarm Output
Remorte ON/OFF Input
1 Required water quality: Add the antirust to the equivalent grade of Japan Refrigeration and Air-­condition Industry Standard for make-­up water (With least PH6 to 8 calcium, silica, chlorine, iron content.) Recommends Matsui antirust.
2 In heat overload exceeding cooling capacity, it isn’t possible to perform temperature control.
3 Uses in maximum flow rate. The flow rate decreases when installing a valve in the middle of a pipeline. Therefore, don’t set the valves.
4 The outer dimensions doesn't include pipe and reserve tank. The pipe port sometimes changes with the convenience of customer.
Temperature Controller
Model
Power Supply