DUAL OUTPUT MODULE FOR CONFIGURABLE M-RCB600 SERIES
MODEL OP-W
DS_OUTPUT W_REV00 _ DECEMBER 2014
DESCRIPTION
The OP-W module is part of the output module
family for the MCB/RCB600, 1200 series of
modular, configurable power supplies.
It provides two independent and isolated
outputs, offering high performance and an
extremely wide voltage adjustability range.
The module is capable of delivering 75 W on each
channel and is perfectly form fit to the others of
the series.
It carries a full set of electrical and thermal
protections.
The OPW is certified to IEC/EN/UL/CSA 60950-1
2nd Ed and ANSI/AAMI ES60601-1; CAN/CSAC22.2 No. 60601-1:08; IEC/EN60601-1:06
CE Mark: Low Voltage Directive 2007/47/EC.
Output
Module
W
Nominal
Voltage
2x 12 V
Voltage
Adjustment
3.3 to 15.0 V
Output Rated
Power
2x 75 W
Rated
Current
5.0 A
Max Current at
Nom Voltage
5.0 A
Load
Regulation
±50 mV
Over Voltage
trip level
20 V
V1 / V2 OUTPUT SPECIFICATIONS
Parameter
Voltage range
Rated current
Rated power
Initial voltage accuracy
Voltage adjustment
Load regulation
Line regulation
Cross regulation
Minimum load
Temperature drift
Ripple and Noise
Transient response
Turn on rise time
Turn on overshoot
Turn on delay
Hold-up voltage
V1/V2 Isolation to ground
Isolation V1 to V2
Over current protection
Reverse current protection
Short circuit protection
Over voltage protection
Over temperature protection
Power good threshold
Reliability
Warranty
Wire size
Size and weight
Test conditions / Notes
Each channel
Each channel
Each channel
Factory set units
Manual: 11-turns potentiometer
Measured at sense terminals
Measured at sense terminals
Measured at sense terminals
Min
3.3
Nominal
12
-1
Max
15
5.0
75
1
1.1
-50
-0.1
-0.2
50
0.1
0.2
0
-0.02
0.02
2
20 MHz bandwidth, peak-to-peak
VSET: 12 V
25% to 75% load transient, at 1A/μs,
recovery to within 10% of VSET
Monotonic, 10 to 90 %
4.5
5.5
From AC on (120 VAC) to Power Good
From Enable to Power Good
250
15
-
Each terminal
Each terminal
Hiccup mode
None
Hiccup period
Hiccup duty cycle
Latching
Internally monitored, latching
High threshold
Low threshold only
At 40 °C, 80% duty cycle, 100% load
Telcordia SR-332 Issue 2
105
19
115
90
88
50
25
20
94
92
Power cables
20
18
(27.5 x 65.9 x 15.7) mm; (1.08 x 2.59 x 0.62) in; 60 g 2.1 oz
1
200
6.5
0.1
350
25
12
250
250
125
21
125
98
95
Units
V
A
W
% VSET
V/turn
mV
%VNOM
%VNOM
A
%/°C
%VNOM
V
μs
ms
%VSET
ms
V
V
V
%IRATED
%IRATED
ms
%
V
°C
%VSET
1
FPMH
2
10
Years
AWG
MECHANICAL SPECIFICATIONS – CONNECTORS AND PIN ASSIGNMENT
Pin Assignment
Circuit
Description
Outline drawing
V1 and V2 Output Voltages
MOLEX 0430450400
1
2
3
4
-V1
-V2
+V1
+V2
Signals
MOLEX 0530480510
1
2
3
4
5
S- (V2)
S+ (V2)
Not connected
S- (V1)
S+ (V1)
Roal Electronics, S.p.A. may change product specifications and accordingly the information presented in this document.
Customers are responsible for their products and applications using Roal Electronics, S.p.A. products. Roal Electronics,
S.p.A. assumes no liability from the use of its products outside of specifications. No license is granted to any intellectual
property rights by this document. ROAL ELECTRONICS, S.P.A. DISCLAIMS ALL REPRESENTATIONS AND WARRANTIES OF
ANY KIND, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, IMPLIED WARRANTIES OF NONINFRINGEMENT,
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
North America
Eu and RoW
ROAL Electronics S.p.A
Via Jesina 56/A
60022 – Castelfidardo (AN) - Italy
Tel:+ 39 071 721461
Fax:+ 39 071 72146 480
www.roallivingenergy.com
ROAL Electronics USA, Inc.
701, Main St. Suite 405
Stroudsburg, PA18360
Phone: + 1 570 421 5750
Fax: +1 570 421 5687
OP-W_Rev00_December 08, 2014