Job:
Approval:
Type:
MR16 Sign Light MODEL SL1
12V, 50W Max., MR16 Halogen
12-24V, 10W or 12V, 12.5W LED
10 5/8"
6"
Clear Anodized. Brass model
Side Mount
Specifications:
available in three additional metal
Material: Available in machined 6061-T6
Style
S1
finishes: Natural, Polished, and
aluminum or C36000 brass.
Rear Mount
Stem Length
1 5/8"
Aged.
Head: Machined head comes in two styles: Side
Mount and Rear Mount. (See illustration for aiming Lens: Tempered, clear lens, secured
Stem Length
6"
to cap with a high temperature, UV
capability of each head style.)
Style
S2
Stem: 1” diameter machined stem comes in various curing, silicone adhesive.
Side Mount
stem lengths and three stem styles: Straight, 180° Socket: GY-6.35 porcelain socket
U-Bend, and 90° Gooseneck. (See illustration for with 600V, 250°C, PTFE coated 18
ga leads.
calculating overall projection from wall for each
Rear Mount
Stem
Lamps:
stem style.)
Length
18"
•12
Volt
bi-pin
MR16
halogen
Knuckle: Rotate and Lock knuckle (protected
up to 50 Watts (maximum
under U.S. Patents #6,966,679, #7,108,405 and
Style
allowable wattage depends on
#7,458,552) mounts the head to the stem and allows
S3
model
and
application.
See
2
3/4"
Note:
for adjustability. Double taper design allows fixture
Side
mount
heads
are
fully
Certification heading).
to hold position during aiming and ensures a solid
Mount
adjustable. Rear mount heads
•12-24 Volt AC/DC, 10W LED
Thickness
are partially adjustable and will
lock when tightened. LED models have a molded
not allow aiming towards wall in
with
High/Low
switch
for
35W
silicone wire seal to prevent water entry at knuckle.
some instances (see diagram
Side Mount
& 20W halogen equivalent
below for allowable adjustment). Rear Mount
Cap: Machined caps lock in place with one 18-8
Projection From Wall
outputs. Requires up to 13W at
stainless steel set screw, and are sealed to the body
1 5/8” (for Style S1)
startup, which must be allowed
with a high temperature silicone O-ring. Regress
Projection From Wall = Stem Length + Mount Thickness + 6” (for Style S2)
for during system design.
18” (for Style S3)
Lens caps have drain holes for water drainage from
•12 Volt AC/DC, 12.5W LED with
top of lens if mounted in the up position. ‘Flush
push button selection of 4 outputs (50W, 35W,
Lens’ cap styles incorporate a stepped lens to reduce
20W & 12W halogen equivalent). Requires up
the collection of water and debris on the lens. All
Rear
Side
to 15W at startup, which must be allowed for
Mount
Mount
caps accept up to three internal accessories, held in
during system design.
360°
360°
place by a stainless steel clip.
LED modules are field replaceable and feature
Mount Canopy: Available with the following
replaceable lenses, an L70 of 60,000 hrs., dynamic
mount options: MO3 (Machined Round Canopy), transformer recognition, phase dimming (see
MO15 (Machined Square Canopy), and MO12
Transformer and Dimmer Compatibility List), and
Ø2 3/8"
(Surface Mount Powered Canopy). See mount
patented LEDSense® thermal management.
specification sheets for more information. (Mount Certification: CSA tested & certified to US and
canopy must be mounted to an appropriate wall or Canadian safety standards for wet location wall
junction box, in such a manner that is capable of
mount (UL1598) use:
C1 Cap
C2 & C2L Caps
C4 & C4L Caps
C3 Cap
holding the weight and torque created by the fixture.
SL1A - 50W Max. MR16 Halogen lamp.
Junction box and hardware not included).
2 1/4"
3/8"
3/8"
SL1B - 35W Max. MR16 Halogen lamp.
Finish: TGIC thermo set polyester powder coat
10W LED & 12.5 LED can be used in all
paint available in 14 standard colors. On aluminum
models and applications.
model, finish is applied over a corrosion resistant, All ratings subject to change without notice. See
hexavalent chromium free, RoHS
MO3 Mount
MO15 Mount
MO12 Mount
web site or contact V3 for most current info.
compliant coating. Aluminum model
available in one additional metal finish:
4 7/8"
5 7/8"
Ø5"
3 1/4"
5"
3 1/4"
4 1/4"
Ø5"
2 1/4"
)
4" ap
C
1
(C
8" )
7/ p
3 Ca
1
(C
Ordering Information:
Model
SL1A - Aluminum
SL1B - Brass 1, 2, 7
Finish
BLT - Textured Black BL - Black
BNT - Textured Bronze BN - Bronze
BAT - Textured Bark WI - White
GRT - Textured Green SI - Silver
GNT - Textured Granite GY - Grey
SAT - Textured Sand BE - Beige
PAT - Textured Patina
EAT - Textured Earth
CLA - Clear Anodized (SL1A only)
NAT - Natural (SL1B only)
POL - Polished (SL1B only)
AGE - Aged (SL1B only)
Head
SM - Side Mount
RM - Rear Mount 8
Cap Style
Stem 7
6 - 6” Stem
12 - 12” Stem
18 - 18” Stem
24 - 24” Stem
30 - 30” Stem
36 - 36” Stem
42 - 42” Stem
48 - 48” Stem
Lamp
Mount
Remote Transformer Required:
MO3 - Round Canopy
MO15 - Square Canopy
MO12 - Surface Mount Canopy
Integral Transformer:
MO12-75-120 - MO12 w/ 75W, 120V
MO12-75-230 - MO12 w/ 75W, 230V 6
MO12-75-277 - MO12 w/ 75W, 277V 6
Standard Lens:
C1 - Flush
C2 - Regress Lens
C2L - Regress Lens, Long
C3 - Regress Lamp
C4 - 45° Angled
Style 1
C4L - 45° Angled, Long S1 - Straight 8
Flush Lens:
S2 - 180° U-Bend (available with 12” up to 42” stem option) 1
C1F - Flush
S3 - 90° Gooseneck (available with up to 30” stem option) 1
C2F - Regress Lens
C2LF - Regress Lens, Long
C3F - Regress Lamp
C4F - 45° Angled
C4LF - 45° Angled, Long
Example: SL1A - BL - SM - C3 - S2 - 24 - MO15 - 01 - 0 - F2 - H1
©2004 - 2013 Vision3 Lighting®
P.O. Box 607, Fowler, CA 93625
MR16 Halogen 2:
0 - None
01 - ESX, 20W, 12°
02 - BAB, 20W, 40°
03 - FRB, 35W, 12°
04 - FRA, 35W, 23°
05 - FMW, 35W, 40°
06 - EYR, 42W, 12°
07 - EYS, 42W, 25°
08 - EYP, 42W, 40°
09 - EXT, 50W, 13°
10 - EXZ, 50W, 26°
11 - EXN, 50W, 40°
12 - FNV, 50W, 60°
Lens Accy 3
Filter 3
Louver 3
LED 5, 6:
0 - None F4 - Green 0 - None
0 - None
116 - 10W, 3000K, 12° 3
L1 - Spread Lens F1 - Red F5 - Amber H1 - Honeycomb
117 - 10W, 3000K, 21° 3
L2 - Linear Lens F2 - Blue F6 - Pink
118 - 10W, 3000K, 41° 3
F3 - Light F7 - Mercury
4 L3 - Softening Lens
119 - 12.5W, 3000K, 19°
Blue Vapor
120 - 12.5W, 3000K, 34° 4
4
121 - 12.5W, 3000K, 60°
Notes:
1. Style S2 and S3 not available with SL1B.
2. Lamps over 35W not available with SL1B.
3. Only two lens accessories can be used with 10W LED.
4. 12.5W LED can only be used with C2L, C2LF, C3, C3F, C4L & C4LF cap styles.
5. Other color temperatures available as a special order.
6. Only power LED with magnetic or V3 approved electronic transformers. LED
lamp options may not be completely compatible with MO12-75-230 and MO1275-277 mounts. Contact V3 for mount, transformer, or dimmer compatibility info.
7. Stem lengths longer than 30” not available with SL1B.
8. Rear Mount head has limited adjustability and will not aim back towards the wall
when on an S1 Style stem. See illustration above for aiming capability.
9. Specifications, certifications, and ordering information are subject to change.
Please check website for latest specification sheets.
(559) 834-5749
(559) 834-4779 fax
www.vision3lighting.com
revision 9/16/13