APP Modified Bitumen Waterproofing Membrane
Soprema Australia Pty Ltd
Chemwatch Hazard Alert Code: 1
Chemwatch: 50-4857
Version No: 2.1.1.1
Safety Data Sheet according to WHS and ADG requirements
Issue Date: 11/06/2015
Print Date: 12/06/2015
Initial Date: Not Available
S.GHS.AUS.EN
SECTION 1 IDENTIFICATION OF THE SUBSTANCE / MIXTURE AND OF THE COMPANY / UNDERTAKING
Product Identifier
Product name
Synonyms
Other means of
identification
APP Modified Bitumen Waterproofing Membrane
Plastiflex, Monogum, Soprasun, Plastigum
Not Available
Relevant identified uses of the substance or mixture and uses advised against
Relevant identified uses
Membranes are used for all types of roofing needs, air barrier and waterproofing protection. NOTE: Under normal use, product is not expected to create any
health hazard.
Details of the manufacturer/importer
Registered company name
Address
Telephone
Fax
Website
Email
Soprema Australia Pty Ltd
Unit 2 / 109 Metrolink Circuit Campbellfield 3061 VIC Australia
+61 3 9308 7962
Not Available
Not Available
[email protected]
Emergency telephone number
Association / Organisation
Emergency telephone
numbers
Other emergency telephone
numbers
Not Available
042 595 2526 (Cruz Utanga: Mon-Fri 7.30am to 4pm)
Not Available
SECTION 2 HAZARDS IDENTIFICATION
Classification of the substance or mixture
NON-HAZARDOUS CHEMICAL. NON-DANGEROUS GOODS. According to the Model WHS Regulations and the ADG Code.
Poisons Schedule
Not Applicable
GHS Classification
Not Applicable
Label elements
GHS label elements
SIGNAL WORD
Not Applicable
NOT APPLICABLE
Hazard statement(s)
Not Applicable
Precautionary statement(s) Prevention
Precautionary statement(s) Response
Precautionary statement(s) Storage
Precautionary statement(s) Disposal
SECTION 3 COMPOSITION / INFORMATION ON INGREDIENTS
Substances
See section below for composition of Mixtures
Mixtures
Continued...
Chemwatch: 50-4857
Page 2 of 8
Version No: 2.1.1.1
APP Modified Bitumen Waterproofing Membrane
CAS No
%[weight]
Issue Date: 11/06/2015
Print Date: 12/06/2015
Name
membrane contains, bituminous blend of;
8052-42-4
30-60
bitumen road making
1317-65-3
30-60
calcium carbonate
Not Available
7-13
atactic polypropylene.
65997-17-3
0.5-7
fibreglass reinforcements
Not Available
5-10
polypropylene film
9002-88-4
0-10
polyethylene
14807-96-6
0-13
talc
14808-60-7
0-13
silica crystalline - quartz
reinforcement contains;
underface and surface contains;
The specific chemical identity and/or exact percentage (concentration) of composition has been withheld as a trade secret.
SECTION 4 FIRST AID MEASURES
Description of first aid measures
Eye Contact
Skin Contact
Inhalation
Ingestion
If this product comes in contact with the eyes:
Wash out immediately with fresh running water.
Ensure complete irrigation of the eye by keeping eyelids apart and away from eye and moving the eyelids by occasionally lifting the upper and lower lids.
Seek medical attention without delay; if pain persists or recurs seek medical attention.
Removal of contact lenses after an eye injury should only be undertaken by skilled personnel.
If skin contact occurs:
Immediately remove all contaminated clothing, including footwear.
Flush skin and hair with running water (and soap if available).
Seek medical attention in event of irritation.
Immediately drench burn area in cold running water.
If hot bitumen adheres to the skin, DO NOT attempt to remove it (it acts as a sterile dressing).
For burns to the head and neck and trunk, apply cold wet towels to the burn area, and change frequently to maintain cooling.
Cooling should be maintained for no longer than thirty minutes.
When hot bitumen completely encircles a limb, it may have a tourniquet effect and should be split as it cools.
Transport to hospital or doctor.
In case of burns:
Immediately apply cold water to burn either by immersion or wrapping with saturated clean cloth.
DO NOT remove or cut away clothing over burnt areas. DO NOT pull away clothing which has adhered to the skin as this can cause further injury.
DO NOT break blister or remove solidified material.
Quickly cover wound with dressing or clean cloth to help prevent infection and to ease pain.
For large burns, sheets, towels or pillow slips are ideal; leave holes for eyes, nose and mouth.
DO NOT apply ointments, oils, butter, etc. to a burn under any circumstances.
Water may be given in small quantities if the person is conscious.
Alcohol is not to be given under any circumstances.
Reassure.
Treat for shock by keeping the person warm and in a lying position.
Seek medical aid and advise medical personnel in advance of the cause and extent of the injury and the estimated time of arrival of the patient.
If fumes or combustion products are inhaled remove from contaminated area.
Lay patient down. Keep warm and rested.
Prostheses such as false teeth, which may block airway, should be removed, where possible, prior to initiating first aid procedures.
Apply artificial respiration if not breathing, preferably with a demand valve resuscitator, bag-valve mask device, or pocket mask as trained. Perform CPR if
necessary.
Transport to hospital, or doctor.
Not considered a normal route of entry.
If swallowed do NOT induce vomiting.
If vomiting occurs, lean patient forward or place on left side (head-down position, if possible) to maintain open airway and prevent aspiration.
Observe the patient carefully.
Never give liquid to a person showing signs of being sleepy or with reduced awareness; i.e. becoming unconscious.
Give water to rinse out mouth, then provide liquid slowly and as much as casualty can comfortably drink.
Seek medical advice.
Indication of any immediate medical attention and special treatment needed
Treat symptomatically.
SECTION 5 FIREFIGHTING MEASURES
Extinguishing media
Foam.
Dry chemical powder.
BCF (where regulations permit).
Carbon dioxide.
Water spray or fog - Large fires only.
Special hazards arising from the substrate or mixture
Fire Incompatibility
None known.
Continued...
Chemwatch: 50-4857
Page 3 of 8
Version No: 2.1.1.1
Issue Date: 11/06/2015
Print Date: 12/06/2015
APP Modified Bitumen Waterproofing Membrane
Advice for firefighters
Alert Fire Brigade and tell them location and nature of hazard.
Wear full body protective clothing with breathing apparatus.
Prevent, by any means available, spillage from entering drains or water course.
Use water delivered as a fine spray to control fire and cool adjacent area.
Avoid spraying water onto liquid pools.
DO NOT approach containers suspected to be hot.
Cool fire exposed containers with water spray from a protected location.
If safe to do so, remove containers from path of fire.
Fire Fighting
Fire/Explosion Hazard
Combustible.
Slight fire hazard when exposed to heat or flame.
Heating may cause expansion or decomposition leading to violent rupture of containers.
On combustion, may emit toxic fumes of carbon monoxide (CO).
May emit acrid smoke.
Mists containing combustible materials may be explosive.
Combustion products include:, carbon dioxide (CO2), sulfur oxides (SOx), hydrogen sulfide (H2S), other pyrolysis products typical of burning organic material
NOTE: Burns with intense heat. Produces melting, flowing, burning liquid and dense acrid black smoke.
SECTION 6 ACCIDENTAL RELEASE MEASURES
Personal precautions, protective equipment and emergency procedures
Clean up all spills immediately.
Secure load if safe to do so.
Bundle/collect recoverable product.
Collect remaining material in containers with covers for disposal.
Minor Spills
Major Spills
Minor hazard.
Clear area of personnel.
Alert Fire Brigade and tell them location and nature of hazard.
Wear physical protective gloves e.g. Leather.
Contain spill/secure load if safe to do so.
Bundle/collect recoverable product and label for recycling.
Collect remaining product and place in appropriate containers for disposal.
Clean up/sweep up area.
|If hot material is spilled, allow enough time to cool completely and remove to a container for disposal.
Personal Protective Equipment advice is contained in Section 8 of the MSDS.
SECTION 7 HANDLING AND STORAGE
Precautions for safe handling
Limit all unnecessary personal contact.
Wear protective clothing when risk of exposure occurs.
Use in a well-ventilated area.
When handling DO NOT eat, drink or smoke.
Always wash hands with soap and water after handling.
Avoid physical damage to containers.
Use good occupational work practice.
Observe manufacturer's storage and handling recommendations contained within this MSDS.
Safe handling
Other information
Keep dry
Conditions for safe storage, including any incompatibilities
Packaging as recommended by manufacturer.
Check that containers are clearly labelled
Suitable container
Avoid reaction with oxidising agents
Avoid strong acids, acid chlorides, acid anhydrides and chloroformates.
Storage incompatibility
PACKAGE MATERIAL INCOMPATIBILITIES
Not Available
SECTION 8 EXPOSURE CONTROLS / PERSONAL PROTECTION
Control parameters
OCCUPATIONAL EXPOSURE LIMITS (OEL)
INGREDIENT DATA
Source
Ingredient
Material name
TWA
STEL
Peak
Notes
Not
Available
Not
Available
Australia Exposure Standards
bitumen road making
Bitumen fumes
5 mg/m3
Not
Available
Australia Exposure Standards
calcium carbonate
Calcium carbonate (a)
10 mg/m3
Not
Available
Not
Available
Not
Available
Australia Exposure Standards
talc
Soapstone (respirable dust) / Talc, (containing no
asbestos fibres)
3 mg/m3 / 2.5
mg/m3
Not
Available
Not
Available
Not
Available
Australia Exposure Standards
silica crystalline quartz
Silica - Crystalline Quartz (respirable dust) / Quartz
(respirable dust)
0.1 mg/m3
Not
Available
Not
Available
Not
Available
Continued...
Chemwatch: 50-4857
Page 4 of 8
Version No: 2.1.1.1
Issue Date: 11/06/2015
Print Date: 12/06/2015
APP Modified Bitumen Waterproofing Membrane
EMERGENCY LIMITS
Ingredient
Material name
TEEL-1
TEEL-2
TEEL-3
bitumen road making
Asphalt; (Bitumen)
0.5 mg/m3
5 mg/m3
30 mg/m3
bitumen road making
Petroleum asphalt
0.5 mg/m3
5 mg/m3
30 mg/m3
calcium carbonate
Limestone; (Calcium carbonate; Dolomite)
27 mg/m3
27 mg/m3
1300 mg/m3
calcium carbonate
Carbonic acid, calcium salt
45 mg/m3
210 mg/m3
1300 mg/m3
fibreglass reinforcements
Fibrous glass; (Fiber glass; Glass frit; Synthetic vitreous fibers)
15 mg/m3
170 mg/m3
990 mg/m3
polyethylene
Polyethylene
10 mg/m3
110 mg/m3
1000 mg/m3
talc
Talc
2 mg/m3
2 mg/m3
2.6 mg/m3
silica crystalline - quartz
Silica, crystalline-quartz; (Silicon dioxide)
0.025 mg/m3
0.025 mg/m3
0.025 mg/m3
Ingredient
Original IDLH
Revised IDLH
bitumen road making
Not Available
Not Available
calcium carbonate
Not Available
Not Available
atactic polypropylene.
Not Available
Not Available
fibreglass reinforcements
Not Available
Not Available
polypropylene film
Not Available
Not Available
polyethylene
Not Available
Not Available
talc
N.E. mg/m3 / N.E. ppm
1,000 mg/m3
silica crystalline - quartz
N.E. mg/m3 / N.E. ppm
50 mg/m3
Exposure controls
Appropriate engineering
controls
General exhaust is adequate under normal operating conditions.
Personal protection
Eye and face protection
Skin protection
Hands/feet protection
Safety glasses with side shields; or as required,
Chemical goggles.
Contact lenses may pose a special hazard; soft contact lenses may absorb and concentrate irritants. A written policy document, describing the wearing of
lenses or restrictions on use, should be created for each workplace or task. This should include a review of lens absorption and adsorption for the class of
chemicals in use and an account of injury experience. Medical and first-aid personnel should be trained in their removal and suitable equipment should be
readily available. In the event of chemical exposure, begin eye irrigation immediately and remove contact lens as soon as practicable. Lens should be removed
at the first signs of eye redness or irritation - lens should be removed in a clean environment only after workers have washed hands thoroughly. [CDC NIOSH
Current Intelligence Bulletin 59], [AS/NZS 1336 or national equivalent]
See Hand protection below
Wear general protective gloves, eg. light weight rubber gloves.
Body protection
See Other protection below
Other protection
No special equipment needed when handling small quantities.
OTHERWISE:
Overalls.
Barrier cream.
Eyewash unit.
Thermal hazards
Not Available
Recommended material(s)
Respiratory protection
GLOVE SELECTION INDEX
Glove selection is based on a modified presentation of the:
"Forsberg Clothing Performance Index".
The effect(s) of the following substance(s) are taken into account in the computergenerated selection:
APP Modified Bitumen Waterproofing Membrane Not Available
Material
CPI
* CPI - Chemwatch Performance Index
A: Best Selection
B: Satisfactory; may degrade after 4 hours continuous immersion
C: Poor to Dangerous Choice for other than short term immersion
NOTE: As a series of factors will influence the actual performance of the glove, a final
selection must be based on detailed observation. * Where the glove is to be used on a short term, casual or infrequent basis, factors such as
"feel" or convenience (e.g. disposability), may dictate a choice of gloves which might otherwise
be unsuitable following long-term or frequent use. A qualified practitioner should be consulted.
Type AX-P Filter of sufficient capacity. (AS/NZS 1716 & 1715, EN 143:2000 & 149:2001, ANSI
Z88 or national equivalent)
Where the concentration of gas/particulates in the breathing zone, approaches or exceeds the
"Exposure Standard" (or ES), respiratory protection is required.
Degree of protection varies with both face-piece and Class of filter; the nature of protection
varies with Type of filter.
Required Minimum
Protection Factor
Half-Face
Respirator
Full-Face
Respirator
Powered Air
Respirator
up to 10 x ES
AX-AUS P2
-
AX-PAPR-AUS /
Class 1 P2
up to 50 x ES
-
AX-AUS / Class
1 P2
-
up to 100 x ES
-
AX-2 P2
AX-PAPR-2 P2 ^
^ - Full-face
A(All classes) = Organic vapours, B AUS or B1 = Acid gasses, B2 = Acid gas or hydrogen
cyanide(HCN), B3 = Acid gas or hydrogen cyanide(HCN), E = Sulfur dioxide(SO2), G =
Agricultural chemicals, K = Ammonia(NH3), Hg = Mercury, NO = Oxides of nitrogen, MB =
Methyl bromide, AX = Low boiling point organic compounds(below 65 degC)
Continued...
Chemwatch: 50-4857
Page 5 of 8
Version No: 2.1.1.1
Issue Date: 11/06/2015
Print Date: 12/06/2015
APP Modified Bitumen Waterproofing Membrane
SECTION 9 PHYSICAL AND CHEMICAL PROPERTIES
Information on basic physical and chemical properties
Appearance
Physical state
Black colour membrane with asphalt odour.
Manufactured
Relative density (Water = 1)
Odour
Not Available
Partition coefficient
n-octanol / water
Not Applicable
Odour threshold
Not Available
Auto-ignition temperature
(°C)
Not Applicable
pH (as supplied)
Not Applicable
Decomposition
temperature
Not Applicable
Melting point / freezing
point (°C)
Not Applicable
Viscosity (cSt)
Not Applicable
Initial boiling point and
boiling range (°C)
Not Applicable
Molecular weight (g/mol)
Not Applicable
Not Available
Flash point (°C)
Not Applicable
Taste
Not Available
Evaporation rate
Not Applicable
Explosive properties
Not Available
Flammability
Not Applicable
Oxidising properties
Not Available
Upper Explosive Limit (%)
Not Applicable
Surface Tension (dyn/cm or
mN/m)
Not Applicable
Lower Explosive Limit (%)
Not Applicable
Volatile Component (%vol)
Not Applicable
Vapour pressure (kPa)
Not Applicable
Gas group
Solubility in water (g/L)
Not Applicable
pH as a solution (1%)
Vapour density (Air = 1)
Not Applicable
VOC g/L
Not Available
Not Applicable
Not Available
SECTION 10 STABILITY AND REACTIVITY
Reactivity
Chemical stability
See section 7
Product is considered stable and hazardous polymerisation will not occur.
Possibility of hazardous
reactions
See section 7
Conditions to avoid
See section 7
Incompatible materials
See section 7
Hazardous decomposition
products
See section 5
SECTION 11 TOXICOLOGICAL INFORMATION
Information on toxicological effects
Inhaled
Ingestion
Skin Contact
Eye
Chronic
APP Modified Bitumen
Waterproofing Membrane
bitumen road making
Not normally a hazard due to physical form of product.
Acute exposure to bitumen/asphalt vapours may cause coughing, chest tightness, muscle weakness, dizziness, tiredness, poor concentration, and even nausea
and vomiting.
Workers exposed to hot blown bitumens show bronchitis, inflammation of the nose, mouth, pharynx and larynx; symptoms include cough, phlegm, burning of the
throat and chest, hoarseness, headache and nasal discharge.
Concentrations of asphalt in the workplace ranges from virtually zero in areas of good mechanical ventilation to 40 mg/m3 where there is very poor natural draft.
Not normally a hazard due to the physical form of product. The material is a physical irritant to the gastro-intestinal tract
Not normally a hazard due to physical form of product.
|Skin contact can cause mechanical irritation, if membrane is torch-applied, asphalt fumes can cause irritation.
Not normally a hazard due to physical form of product.
Workers exposed to fumes of blown bitumens developed inflammation of the cornea and conjunctiva.
|Contact with this product at high temperature can cause thermal burns.
Generally not applicable.
Long-term exposure to bitumen or asphalt fumes, over extended periods, may cause central nervous system depression and liver and kidney changes. Chronic
bitumen/asphalt poisoning may result in a decrease in the number of white and red blood cells.
Prolonged contact with bitumens may produce irritation, inflammation, dermatitis, acne-like lesions, keratoses, melanosis and sensitivity to light.
Animal testing for cancer-causing effects of bitumen was inconclusive, and no difference was found between the health of asphalt workers and of groups of
controls in oil refineries.
TOXICITY
IRRITATION
Not Available
Not Available
TOXICITY
IRRITATION
Dermal (rabbit) LD50: >2000 mg/kg [1]
Oral (rat) LD50: >5000 mg/kg
Not Available
[1]
Continued...
Chemwatch: 50-4857
Page 6 of 8
Version No: 2.1.1.1
Issue Date: 11/06/2015
APP Modified Bitumen Waterproofing Membrane
TOXICITY
calcium carbonate
fibreglass reinforcements
dermal (rat) LD50: >2000 mg/kg
IRRITATION
[1]
Eye (rabbit): 0.75 mg/24h - SEVERE
Oral (rat) LD50: >2000 mg/kge[1]
Skin (rabbit): 500 mg/24h-moderate
TOXICITY
IRRITATION
Not Available
Not Available
TOXICITY
Dermal (rabbit) LD50: >2000 mg/kg
polyethylene
Print Date: 12/06/2015
IRRITATION
[2]
Not Available
Inhalation (mouse) LC50: 12 mg/L/30m[2]
Inhalation (rat) LC50: 75.5 mg/L/30M[2]
Oral (rat) LD50: >3000 mg/kg [2]
talc
silica crystalline - quartz
Legend:
BITUMEN ROAD MAKING
CALCIUM CARBONATE
FIBREGLASS
REINFORCEMENTS
POLYETHYLENE
TALC
TOXICITY
IRRITATION
Not Available
Skin (human): 0.3 mg/3d-I mild
TOXICITY
IRRITATION
Not Available
Nil reported
1. Value obtained from Europe ECHA Registered Substances - Acute toxicity 2.* Value obtained from manufacturer's msds. Unless otherwise specified data
extracted from RTECS - Register of Toxic Effect of chemical Substances
No significant acute toxicological data identified in literature search.
Asthma-like symptoms may continue for months or even years after exposure to the material ceases. This may be due to a non-allergenic condition known
as reactive airways dysfunction syndrome (RADS) which can occur following exposure to high levels of highly irritating compound. Key criteria for the
diagnosis of RADS include the absence of preceding respiratory disease, in a non-atopic individual, with abrupt onset of persistent asthma-like symptoms
within minutes to hours of a documented exposure to the irritant. A reversible airflow pattern, on spirometry, with the presence of moderate to severe
bronchial hyperreactivity on methacholine challenge testing and the lack of minimal lymphocytic inflammation, without eosinophilia, have also been included
in the criteria for diagnosis of RADS. RADS (or asthma) following an irritating inhalation is an infrequent disorder with rates related to the concentration
of and duration of exposure to the irritating substance. Industrial bronchitis, on the other hand, is a disorder that occurs as result of exposure due to high
concentrations of irritating substance (often particulate in nature) and is completely reversible after exposure ceases. The disorder is characterised by
dyspnea, cough and mucus production.
The material may produce severe irritation to the eye causing pronounced inflammation.
No evidence of carcinogenic properties. No evidence of mutagenic or teratogenic effects.
Insulation wools dissolve more readily in body fluids than most other MMVFs and thus do not persist in the lung. Large fibres (e.g. rock wool, specialapplication fibre glasses, RCF1, amosite and crocidolite asbestos) generally persist longer than small fibres (e.g. insulation fibre glasses, slag wool,
and stone wool) and thus are of generally greater toxicity, with effects varying from lung inflammation to cancers.
No significant acute toxicological data identified in literature search.
The substance is classified by IARC as Group 3:
NOT classifiable as to its carcinogenicity to humans.
Evidence of carcinogenicity may be inadequate or limited in animal testing.
polyethylene pyrolyzate
Asthma-like symptoms may continue for months or even years after exposure to the material ceases. This may be due to a non-allergenic condition known
as reactive airways dysfunction syndrome (RADS) which can occur following exposure to high levels of highly irritating compound. Key criteria for the
diagnosis of RADS include the absence of preceding respiratory disease, in a non-atopic individual, with abrupt onset of persistent asthma-like symptoms
within minutes to hours of a documented exposure to the irritant. A reversible airflow pattern, on spirometry, with the presence of moderate to severe
bronchial hyperreactivity on methacholine challenge testing and the lack of minimal lymphocytic inflammation, without eosinophilia, have also been included
in the criteria for diagnosis of RADS. RADS (or asthma) following an irritating inhalation is an infrequent disorder with rates related to the concentration
of and duration of exposure to the irritating substance. Industrial bronchitis, on the other hand, is a disorder that occurs as result of exposure due to high
concentrations of irritating substance (often particulate in nature) and is completely reversible after exposure ceases. The disorder is characterised by
dyspnea, cough and mucus production.
No significant acute toxicological data identified in literature search.
WARNING: For inhalation exposure ONLY: This substance has been classified by the IARC as Group 1: CARCINOGENIC TO HUMANS
SILICA CRYSTALLINE QUARTZ
The International Agency for Research on Cancer (IARC) has classified occupational exposures to respirable (<5 um) crystalline silica as being
carcinogenic to humans . This classification is based on what IARC considered sufficient evidence from epidemiological studies of humans for the
carcinogenicity of inhaled silica in the forms of quartz and cristobalite. Crystalline silica is also known to cause silicosis, a non-cancerous lung disease.
Intermittent exposure produces; focal fibrosis, (pneumoconiosis), cough, dyspnoea, liver tumours.
* Millions of particles per cubic foot (based on impinger samples counted by light field techniques).
NOTE : the physical nature of quartz in the product determines whether it is likely to present a chronic health problem. To be a hazard the material must
enter the breathing zone as respirable particles.
Acute Toxicity
Carcinogenicity
Skin Irritation/Corrosion
Reproductivity
Continued...
Chemwatch: 50-4857
Page 7 of 8
Version No: 2.1.1.1
Issue Date: 11/06/2015
Print Date: 12/06/2015
APP Modified Bitumen Waterproofing Membrane
Serious Eye
Damage/Irritation
STOT - Single Exposure
Respiratory or Skin
sensitisation
STOT - Repeated Exposure
Mutagenicity
Aspiration Hazard
– Data required to make classification available
– Data available but does not fill the criteria for classification
– Data Not Available to make classification
Legend:
CMR STATUS
Not Applicable
SECTION 12 ECOLOGICAL INFORMATION
Toxicity
DO NOT discharge into sewer or waterways.
Persistence and degradability
Ingredient
Persistence: Water/Soil
Persistence: Air
polyethylene
LOW
LOW
Bioaccumulative potential
Ingredient
Bioaccumulation
polyethylene
LOW (LogKOW = 1.2658)
Mobility in soil
Ingredient
Mobility
polyethylene
LOW (KOC = 14.3)
SECTION 13 DISPOSAL CONSIDERATIONS
Waste treatment methods
Recycle wherever possible or consult manufacturer for recycling options.
Consult State Land Waste Management Authority for disposal.
Bury residue in an authorised landfill.
Recycle containers if possible, or dispose of in an authorised landfill.
Product / Packaging
disposal
SECTION 14 TRANSPORT INFORMATION
Labels Required
Marine Pollutant
HAZCHEM
NO
Not Applicable
Land transport (ADG): NOT REGULATED FOR TRANSPORT OF DANGEROUS GOODS
Air transport (ICAO-IATA / DGR): NOT REGULATED FOR TRANSPORT OF DANGEROUS GOODS
Sea transport (IMDG-Code / GGVSee): NOT REGULATED FOR TRANSPORT OF DANGEROUS GOODS
SECTION 15 REGULATORY INFORMATION
Safety, health and environmental regulations / legislation specific for the substance or mixture
bitumen road
making(8052-42-4) is found
on the following regulatory
lists
calcium
carbonate(1317-65-3) is
found on the following
regulatory lists
fibreglass
reinforcements(65997-17-3)
is found on the following
regulatory lists
polyethylene(9002-88-4) is
found on the following
regulatory lists
talc(14807-96-6) is found on
the following regulatory
lists
"Australia Exposure Standards","International Agency for Research on Cancer (IARC) - Agents Classified by the IARC Monographs","Australia Hazardous
Substances Information System - Consolidated Lists"
"Australia Exposure Standards"
"Australia Hazardous Substances Information System - Consolidated Lists"
"International Agency for Research on Cancer (IARC) - Agents Classified by the IARC Monographs"
"Australia Exposure Standards","International Agency for Research on Cancer (IARC) - Agents Classified by the IARC Monographs","Australia Hazardous
Substances Information System - Consolidated Lists"
Continued...
Chemwatch: 50-4857
Page 8 of 8
Version No: 2.1.1.1
APP Modified Bitumen Waterproofing Membrane
Issue Date: 11/06/2015
Print Date: 12/06/2015
silica crystalline quartz(14808-60-7) is found
on the following regulatory
lists
"Australia Exposure Standards","International Agency for Research on Cancer (IARC) - Agents Classified by the IARC Monographs","Australia Hazardous
Substances Information System - Consolidated Lists"
National Inventory
Status
Australia - AICS
Y
Canada - DSL
Y
China - IECSC
Y
Europe - EINEC / ELINCS /
NLP
N (polyethylene)
Japan - ENCS
N (fibreglass reinforcements)
Korea - KECI
Y
New Zealand - NZIoC
Y
Philippines - PICCS
Y
USA - TSCA
Y
Legend:
Y = All ingredients are on the inventory N = Not determined or one or more ingredients are not on the inventory and are not exempt from listing(see specific
ingredients in brackets)
SECTION 16 OTHER INFORMATION
Other information
Ingredients with multiple cas numbers
Name
CAS No
calcium carbonate
1317-65-3, 13397-26-7, 146358-95-4, 15634-14-7, 198352-33-9, 459411-10-0, 471-34-1, 63660-97-9, 72608-12-9, 878759-26-3
silica crystalline - quartz
122304-48-7, 122304-49-8, 12425-26-2, 1317-79-9, 14808-60-7, 70594-95-5, 87347-84-0
Classification of the preparation and its individual components has drawn on official and authoritative sources as well as independent review by the Chemwatch Classification committee using
available literature references.
A list of reference resources used to assist the committee may be found at:
www.chemwatch.net
The (M)SDS is a Hazard Communication tool and should be used to assist in the Risk Assessment. Many factors determine whether the reported Hazards are Risks in the workplace or other
settings. Risks may be determined by reference to Exposures Scenarios. Scale of use, frequency of use and current or available engineering controls must be considered.
This document is copyright.
Apart from any fair dealing for the purposes of private study, research, review or criticism, as permitted under the Copyright Act, no part may be reproduced by any process without written
permission from CHEMWATCH.
TEL (+61 3) 9572 4700.
end of SDS