Installation Instructions for
980TWIL20CH
Twilight 12, 20
HS44_410_
1.1
Chandeliers
GENERAL PRODUCT INFORMATION:
This product can mount to either a 4" square electrical box with
round plaster ring or an octagon electrical box.
This product is suitable for indoor dry locations only.
This product can be dimmed with a low-voltage electronic dimmer.
CAUTION - RISK OF FIRE
This product requires installation by a qualified
electrician. Before installing be sure to read all
instructions and TURN THE POWER TO THE
ELECTRICAL BOX OFF.
Install the Canopy
1A
1C
BACKPLATE
CROSSBAR
CANOPY
4
1
1
CAP NUT
BACKPLATE
NUT
1
Remove the two cap nuts to lift the backplate out of the
canopy.
4
1B
Screw the crossbar assembly onto the backplate to form an
“X” and secure it to the backplate with a nut.
1D
5
THREADED NIPPLE
3
NUT
#8-32 SCREW
6
6
2
1/4"
CROSSBAR
5
2
Screw the threaded nipple onto the crossbar so that 1/8” to
1/4” is exposed on the other side of the crossbar.
3
Secure the threaded nipple in position by tightening the nut
against the crossbar.
1
5
Connect the fixture to a suitable ground in accordance with
local electrical codes.
6
Mount the crossbar assembly to the electrical box with two
#8-32 screws.
1E
NOTE: The 12 light version does not have a hub plate. If
installing a 12 light, skip to section 4.
5
Install the Hub Plate (20 Light Only)
7
2A
8
OUTER CAP
NUT
1
WASHER
INNER CAP
NUT
1
CAP NUT
7
Connect the canopy white wire to the neutral power line wire
with a wire nut.
8
1
Connect the canopy black wire to the hot power line wire
with a wire nut.
Remove the two inner cap nuts and washers.
2B
STEM
1F
2
THREADED
RODS
HUB PLATE
CAP NUTS
10
10
9
Place all wires and wire nut connections properly inside the
canopy housing.
10
3
Slide the canopy housing onto the backplate threaded rods and
secure it in place by tightening the two cap nuts completely to
the threaded rods.
1G
2MM ALLEN
WRENCH
M3 SET
SCREW
11
11
POWER POST
STEM
Push the stem completely into the canopy’s center power post,
and tighten the two bottom two M3 set screws with the
provided 2 MM Allen wrench.
To raise the chandelier height: Determine the desired
length of the stem, remove the stem from the power
post, and follow the instructions on the next page.
2
WASHER
CAP NUT
3
2
Slide the hub plate center hole completely onto the stem.
3
Align the hub plate holes with the inner power posts. Secure
the hub plate in place by tightening the cap nuts and washer
completely to the power posts.
Install the Fixture Arms for 20 Light
3A
S
M
S
5
L
NOTE: This section is for the installation of the arms
for the 20 light version. Skip to the section 4 for the 12
light version.
S
L
M
S
S
HUB PLATE
M
L
1
Insert the arm of a long socket assembly into one of the
bottom hub holes and tighten the M3 set screw with the
provided 1.5 MM Allen wrench.
2
Feed the stripped portion of the long socket assembly wire
into the provided metal sleeve, and into the nearest "L" port
onto the hub plate. Tighten the M4 set screw with the 2 MM
Allen wrench.
3
Repeat steps 1 & 2 for the remaining four long socket assembly
wires.
4
Repeat steps 1 through 3, using the medium socket assembly
wires middle hub, and the "M" posts on the hub plate.
5
Repeat steps 1 through 3, using the short socket assembly wire
top hub and the "S" posts on the hub plate.
4
S
S
L
M
L = Long Socket Assembly Wire
M = Medium Socket Assembly Wire
2
L
M
S
S
S
S = Short Socket Assembly Wire
2
"L" POST
WIRE
ASSEMBLY
METAL
SLEEVE
WIRE
ASSEMBLY
5
HUB
M4 SET
SCREW
2MM ALLEN
WRENCH
4
3
ARM
3
Shortening the Chandelier (Optional)
3B
CUT
HERE
A
Review the steps above for installing the fixture arms before
continuing.
B
Cut the stem down from the top with an appropriate cutter
(like a hacksaw), and deburr the cut end with a file or grinder.
C
Lay the stem on a flat surface. Attach a short socket arm to
the bottom hub, and pull the wire on the arm to the top end
of the stem. Cut the wire down to that length.
D
Remove the arm from the hub, and lay it next to the other
short arms. Measure and cut the remaining wires to the same
length and strip the last 1/4” of each wire.
E
Repeat steps A-D above for the medium-length arms on the
middle hub, and the long arms on the top hub.
F
Return to step 11 on the previous page and continue with the
installation.
3C
6
M4 SET SCREW
2 MM ALLEN
WRENCH
6
If necessary, loosen the set screw on the hub with an Allen
wrench to adjust the hub. Re-tighten the set screw after
adjustment.
4
Install the Fixture Arms for 12 Light
4A
S
L
4
NOTE: This section is for the 12 light version only.
L
2
L
L
1
Insert the arm of a long socket assembly into one of the
bottom hub holes and tighten the M3 set screw with the
provided 1.5 MM Allen wrench.
2
Feed the stripped portion of the long socket assembly wire
into the provided metal sleeve, and into the nearest "L" port
onto the canopy. Tighten the M4 set screw with the 2 MM
Allen wrench.
3
Repeat steps 1 & 2 for the remaining eight long socket
assembly wires.
4
Repeat steps 1 through 3, using the short socket assembly wire
top hub and the "S" posts on the canopy.
CANOPY
5
S
S
L
L = Long Socket Assembly Wire
L
L
L
S
S = Short Socket Assembly Wire
2
“L" POST
WIRE
ASSEMBLY
METAL
SLEEVE
WIRE
ASSEMBLY
4
HUB
M4 SET
SCREW
2MM ALLEN
WRENCH
3
ARM
5
Shortening the Chandelier (Optional)
4B
CUT
HERE
A
Review the steps above for installing the fixture arms before
continuing.
B
Cut the stem down from the top with an appropriate cutter
(like a hacksaw), and deburr the cut end with a file or grinder.
C
D
E
Lay the stem on a flat surface. Attach a short socket arm to
the bottom hub, and pull the wire on the arm to the top end
of the stem. Cut the wire down to that length.
Remove the arm from the hub, and lay it next to the other
short arms. Measure and cut the remaining wires to the same
length and strip the last 1/4” of each wire.
Repeat steps A-D above for the long-length arms on the
middle hub, and the long arms on the top hub.
4C
5
M4 SET SCREW
2 MM ALLEN
WRENCH
5
If necessary, loosen the set screw on the hub with an Allen
wrench to adjust the hub. Re-tighten the set screw after
adjustment.
6
Install the Lamps & Glass Shade
Install the Flite paper (Optional)
5A
6A
CURVED SECTION
SOCKET
LAMP
1
SLOT
NOTE: Use only your fingers and a soft cloth to install
the lamp.
Use MAX 10 Watt Bi-Pin Xenon (Xelogen)
Lamp With Each Socket.
For each socket, push the lamp pins completely into the socket
holes.
1
5B
SPRING CLIP
GLASS SHADE
2
1
2
Push the glass shade completely onto the spring clip.
Additional spring clips are available in the accessories bag.
7
Wrap the Flite Paper (if provided with the fixture) around the
lamp and insert the curved section into the slot and slide it to
lock it in place.
SAVE THESE INSTRUCTIONS!
7400 Linder Ave, Skokie, IL 60077
800.323.3226 - 847.626.6300
www.lbllighting.com
© 2013 LBL Lighting.All rights reserved.The "LBL Lighting" graphic is a
registered trademark of LBL Lighting. LBL Lighting reserves the right to
change specifications for product improvements without notification.
A Generation Brands Company
8