1065 CLASSROOM MULTIMEDIA
U W F
O X
- I
N F O R M A T I O N
&
I
N S T R U C T I O N A L
T
E C H N O L O G Y
OPERATING INSTRUCTIONS
To Play a DVD/CD or VHS:
1. Turn on all the media equipment in the cabinet. (JVC VCR player, ONKYO AV Receiver, and
Sony DVD player)
2. (Only when playing a DVD) Press the BD/DVD button on the ONKYO receiver. BD/DVD should
be displayed on the front of the receiver.
3. (Only when playing a VHS) Press the VCR/DVR button on the ONKYO receiver. VCR/DVR
should be displayed on the front of the receiver.
4. For the audio, adjust the volume control knob accordingly.
Experiencing problems?
1. I cannot hear any audio. (1. Check to make sure the volume is turned up enough. 2. Below the
Power button there are options for speakers “A” and “B”. Only speakers “A” button should be
pressed in.)
2. I turned on the projector and switched the input to S-VIDEO but all I can see is a blue screen.
(Possible answer: Make sure all the media equipment is turned on and the receiver is set to the
correct output.)
3. The projector is on and all the equipment in the cabinet is on with the right settings but I am still
getting a blue screen. (Possible Answer: Try pressing the VIDEO button on the projector remote.
Pressing it more than once will cycle it between VIDEO and S-VIDEO. Select S-VIDEO.)
4. The DVD player will not turn on. (Possible Answer: The ONKYO AV Receiver might have to be
turned on first in order to power the DVD player.)
** If you require further assistance, please call the Helpdesk @ x2719 or (832-2719), or visit us at room
#1719.
Important: Remember to TURN OFF all units after use!
(Projector power button must be pressed twice to turn off)
1065 CLASSROOM MULTIMEDIA
U W F
O X
- I
N F O R M A T I O N
&
I
N S T R U C T I O N A L
T
E C H N O L O G Y
OPERATING INSTRUCTIONS
To Display the Computer Screen from the Data Projector:
1. Turn on the Hitachi Data Projector. Then press the Computer button on the Hitachi Data
Projector remote until Computer 1 is displayed on the bottom of the projection screen.
2. Turn on the Computer. If the projector is on the right input, the computer screen will be displayed
on the projection screen.
3. For audio, turn on the ONKYO AV Receiver in the media cabinet. Select CD as the input source
and adjust the volume control knob accordingly.
Experiencing problems?
1. I cannot hear any audio. (1. Make sure the CD input is selected on the ONKYO AV Receiver. 2.
Check to make sure the volume is turned up on both the Audio Center and the computer and not
muted on the computer. 3. Below the Power button there are options for speakers “A” and “B”.
Only speakers “A” button should be pressed in.)
2. The projector and the computer are on, but I am still getting a blue screen on the projection screen.
(Possible Answer: Try pressing the Computer button on the Hitachi projector remote. Pressing it
more than once will cycle it between RGB1 and RGB2. Select RGB1.)
** If you require further assistance, please call the Helpdesk @ x2719 or (832-2719), or visit us at room
#1719.
Important: Remember to TURN OFF all units after use!
(Projector power button must be pressed twice to turn off)
1065 CLASSROOM MULTIMEDIA
U W F
O X
- I
N F O R M A T I O N
&
I
N S T R U C T I O N A L
T
E C H N O L O G Y
OPERATING INSTRUCTIONS
To Display the Elmo Document Camera on the Projection Screen:
1. Turn on the ONKYO Av Receiver and press the AUX button on the receiver. AUX should now
be displayed on the front of the receiver.
2. Turn on the Elmo Document Camera. The power switch can be found on the left side of the
camera.
3. Turn on the Hitachi Video/Data Projector (it takes about 15 seconds to turn on) and make sure the
video input is set to VIDEO. To do this, press the VIDEO button on the Hitachi remote and
cycle through until Video appears on the bottom of the projection screen.
** If you require further assistance, please call the Helpdesk @ x2719 or (832-2719), or visit us at room
#1719.
Important: Remember to TURN OFF all units after use!
(Projector power button must be pressed twice to turn off)