SOLENOID APPLICATION REVIEW WORKSHEET
Contact Information:
Date (mm/dd/yy):
/
/
Organization:
Contact Person:
Title:
Email:
Phone #:
Address:
City:
State/Province:
Postal Code:
Country:
Customer Type:
☐OEM
☐End-User
☐Distributor
Market Application:
☐Medical
☐Bioprocessing
☐Industrial
☐Other:
NOTE: All information in the application review worksheet is intended to help us specify the correct product for your application. Please complete
form to the best of your ability for proper evaluation of your application. Information is for internal use only and will not be shared with other entities
without permission from the contact person listed above or a designated company representative.
Application General Description: (Please tell us how you intend to use our valve):
NOTE: Not all of the below preferences or options are available with all valve models.
Industry Certifications, Compliances, and/or Standards Required:
☐CE
☐RoHS
☐REACH
☐WEEE
☐IP
☐Other:
Product Lines/Models of Interest:
Legacy:
☐904
☐955
☐958
Versagrip:
☐1100
☐1300
☐1350
Manual Override Required:
☐Yes
☐No
Tube Slot Config.:
☐Normally-Closed ☐Normally-Open
☐Cassette (Normally-Closed)
Material Preference:
☐Aluminum
☐Black Acetal
Mounting Orientation:
☐Horizontal
☐Vertical
☐Conflict Minerals
☐960
☐1400
☐1450
☐Preferred, not required
☐Dual-Slot (Toggle)
☐Stainless Steel
☐Other:
Application Details:
Intended Operating Environment (Lab/Surgery Room/Production Floor, etc.):
Expected Ambient Temperature:
☐°F
☐°C
Available Power:
VDC x
Amps (Recommend 24VDC x 3 Amps)
(Upon Completion Please Email to [email protected])
Solenoid Application Worksheet
ENG-012-C
Page 1 of 2
Updated: 2015-Nov-30
Application Specifications:
Tubing 1: MFR*:
Catalog/Model #*:
Tubing 1: Material*:
Size: ID*
Tubing 2: MFR:
OD*
Durometer**
Catalog/Model #:
Tubing 2 Material:
Size: ID
Fluid/Media Pressure or Vacuum Range*:
OD
-
Maximum Media Pressure Required to Seal*:
Durometer**
☐PSI
☐Bar
☐mmHg
☐PSI
☐Bar
☐mmHg
*These fields helps us size a valve for your application. These are required.
**Acro valves are intended for use with tubing in the 50-70 Shore A Durometer range.
Fluid/Media Type:
Media Temp. Range:
☐°F ☐°C
-
Desired Flow Rate:
Cycle Rate Nominal:
☐cycles/sec ☐cycles/min ☐cycles/hour
Cycle Rate Maximum:
☐cycles/sec ☐cycles/min ☐cycles/hour
☐seconds
Estimated Maximum Actuated Time:
☐None
PLC used with Valve:
☐Yes: Brand:
☐minutes
☐hours
Model:
Please add any other details that may be help us find a valve for you:
Supporting Accessories:
Solenoid Driver Board1:
☐VDB (Versagrip)
Desired Trigger Voltage: ☐3-24 VDC (VDB)
☐None (will provide own driver)
1
All of our solenoid pinch valves require a solenoid driver which is not supplied unless requested. Bimba|Acro Drivers are
designed to optimize valve performance while reducing overall power consumption. We offer drivers as an accessory or
customers can provide their own drive circuitry.
Position Sensing:
☐Yes
☐No
Sensor/Switch Type:
Legacy:
☐Digital Hall2
Versagrip:
☐Optical
☐Analog Hall
☐Mechanical
☐Optical (904)
2
We typically only provide NPN (sinking) signal output – contact us if you have other needs.
Additional Valve-to-Board Cabling Required3:
Special Cabling Needs:
☐12 inch ☐1 Meter ☐3 Meter
☐Other:
3
Versgrip Pinch Valves come standard with 12” valve-to-board wiring. Legacy valves come standard with 12” leads and connector
designed to interface with additional cabling for 900R Driver Board. Custom/Modified cabling is available upon request.
(Upon Completion Please Email to [email protected])
Solenoid Application Worksheet
ENG-012-C
Page 2 of 2
Updated: 2015-Nov-30