MJH LED Co2 Jet
Manual
PRODUCTION INTRODUCTION
This machine is our unique stage effect product, it is whole new exterior design,
consummate produce technical, original technical performance, make it is in the lead
position among all others of its class. With our company experience in special effects for
many years and extract the strongpoint of stage effect equipment. We manufacture this
more powerful, and more Compatibility, easy operational product.
CHECKING BEFORE OPENING BOX
Please check the box whether it is in good condition before opening it. If find the box is
broken in transport please inform the transport company in time and keep the broken box as
proof so we can claim to transport company for compensation
The packing list below:
1.
1 pc led co2 jets
2.
1 pc dmx signal cable
3.
1 pc hose for co2
4.
1 pc manual
1
TECHNICAL PARAMETER
Voltage: AC 220 V / 50 Hz (110 V available)
Power: 100 W Control mode: DMX control
Working pressure: 5 MPa DMX Channel: 2
Size: 460 (H) x330(L)x330(W)
Weight: 11.6KG
Effect Height : 10 M
Working pressures MPa
INSTRUCTIONS:
INSTALLATION INSTRUCTIONS
INSTALL AS THE FOLLOWING PLEASE:
1. Putting the machine on the corresponding position;
2. Connect the pipeline with quick connector in the machine（Push back the sleeve, point the
pipeline into the connector of the machine, then release the sleeve）;
3. Connect the pipeline with gas cylinder;
4. Lying down the gas cylinder to let the end of it higher a little (if siphon cylinder, no need
this);
5. Connect the machines with controller though control cables, connect units with power con
cable or plug into power socket;
6. Turn on power of controller and units;
7. If everything well, open the valve of the gas cylinder, and the equipment is ready for
show now;
8. When uninstall, close the valve of co2 gas cylinder first, press button of controller to
make machines spray co2 again to let the remaining gas out, then turn off power, take
down the pipeline.
Notice:
1. Let the CO2 tank lie down and the bottom a little high than top, otherwise the gas will not
spray out (if siphon cylinder, no need this);
2. Make sure all units connected with cylinder and controller well.
3. The machine uses AC220V/50Hz (110V available) Voltage.
4. Don’t install equipment when power on!
5. Please make sure the connection reliable before your turn on the power of controller.
OPERATION METHOD
After installing, please operating machine as the following:
1.
Setting dmx address:
It is controlled by dmx, each unit need 2 dmx channel, the dmx address should be set as
001. 003, 005, 007 … (if start from 001). You can set the LED color light before spraying
(by push the bar) or in the spraying.
Note: Color display-please check the led color value table
2. Operation: Turn on the power. Set a program as your want, press the button of controller,
the machines sprays co2 gas as your want.
3. When finishing, close the valve of co2 gas cylinder first, press button of controller to make
machines spray co2 again to let the residual gas out which is stayed in the hose and
machine, then turn off the power, and take down the pipeline.
4.
Clean the machines after usage.
NOTICE
To spray co2 fog continuously no more than 2 second.
The interval time of two shots is not less than 5 second.
DMX Channel:
DMX Channel
1st Channel
2rd Channel
Function
Change the color of led lamp
Open the valve
LED Color Value
DMX Value
Color
30-60
60-90
90-120
120-150
150-180
180-210
210-255
Green
Red
Blue
Yellow
Purple
Sky Blue
White
TROUBLESHOOTING
The program of machine is not working: please check the dmx address of machines and
controller are correct.
1. If it can’t work: check the power supply if connecting right, or the co2 tank is full of enough
liquid co2.
2. If there is no co2 fog to spray: check if it is enough co2 gas in the tank, or check whether the
tank is turned on, or the gas tank is laid inclined.
WARRANTY:
1 year free warranty with whole equipments.
1. The following accident does not within the scope of free services:
2. Damaged by improper transport, install, use by user.
3. Disassemble the products by yourselves caused damage.
4. Abnormal voltages, and fire etc external problem causes damage.
5. Damaged by other force majeure, such as lightning, earthquakes etc.
4