I:Deal ® Reference Card
Please go to www.paniniportal.com to register your scanner, purchase supplies,
obtain technical support or determine your scanner configuration.
3
External Components
The major components of the
Panini I:Deal scanner are:
4
2
5
1. Feeding tray
1
2. LED status indicator
3. Exit pocket
4. Top cover
5. Top cover release button
LED Status Lights
LED
Description
OFF
Device disconnected or software
not connected.
Preparing Documents for Processing
YELLOW
BLINKING
Device connected, software
connected but pocket flaps
are closed.
To reduce the possibility of transport errors and damage
to the unit, you should perform the following steps prior
to feeding the documents:
YELLOW
SOLID
Device connected, software
connected, pocket flaps open.
1. Remove all folds and creases in the document.
GREEN
Device is ready to begin feeding
(device connected, software
connected, pocket flaps open and
feeding enabled).
2. Remove any paper clips, staples, pins,
rubber bands, etc. from the document.
GREEN
BLINKING
Machine is processing documents.
RED
BLINKING
Document jam or misalignment.
RED
SOLID
Firmware being updated.
For detailed operation instructions please refer to the I:Deal Operator Manual. © 2010 Panini S.p.A., All Rights Reserved.
PANINI SpA
Via Po 39
10124 Torino, Italy
Phone: +39.011.8176011
Panini North America
577 Congress Park Drive
Dayton, OH 45459
Phone: +1.937.291.2195
Panini Limitada
Rua Joaquim Floriano, 871 – 11ºA
CEP 04534-013 São Paulo – Brazil
Phone: +55.11.31685521
Feeding Documents
Cleaning
1. Open the exit pocket flaps by lifting up on the
flap handle.
The I:Deal™ has been designed as a minimal
maintenance device. As such no regular cleaning
schedule has been defined. However, occasional
cleaning of the device can help achieve optimal results.
2. Insert document face up with the MICR line aligned
to the right side of the scanner into the right side of
the feeding tray (as indicated by the check icon).
3. Once the document is inserted, the machine will
detect the presence of the document and will begin
feeding. The device will automatically align the
document to the proper position regardless of the
angle or alignment in which the document is inserted
into the unit.
4. The document is scanned and, depending on the
scan mode selected by the application, will either
scan and stop in the exit pocket (which holds up to
10 documents) or scan and return to the feeding
tray for easy removal.
Clearing Jams
When a jam occurs, the paper path must be cleared.
Before cleaning remember to disconnect the USB and
power cables from the device.
1. Cleaning Inside of Unit: Remove paper dust and
small debris from device by using low pressure
canned air or a dusting brush designed for use on
electronic equipment.
2. Cleaning Outside of Unit: The outside cabinetry
can be cleaned to remove finger marks and dust
with a damp cloth and mild soap.
3. Cleaning the Contact Image Sensors: Open the
top cover and manually flip the CIS by rotating the
assembly toward the rear of the machine, then
lift the arm with the green bar on the right side.
Remove any debris and dust. Clean the Contact
Image Sensors with a soft, lint-free cloth dampened
with isopropyl alcohol or with eye glass cleaner.
1. The paper path can be easily accessed simply by
opening the cover and extracting the jammed
document by gently pulling it out with your fingers.
2. When clearing a jam, clear the paper path and
rollers from any documents, paper dust or debris.
3. Close cover to resume operation. Ensure the cover
is fully closed.
For detailed operation instructions please refer to the I:Deal Operator Manual. © 2010 Panini S.p.A., All Rights Reserved.
Written by PANINI.
PANINI and I:Deal are trademarks
or registered trademarks of PANINI S.p.A.
Specifications subject to change without previous notice.
This material may not be reproduced without the
express written consent of PANINI S.p.A.
www.panini.com