1. Installation
2. Main Control Panel
3. Maintenance
4. Function Key Quick Reference
Installation:
1. Place the magnetic holder's at the side of the tank. For the Nano place about 10cm
below the water level. Conch II / III place below the water level between 15CM ~ 20CM.
2. Install Wave Maker on the Magnetic Holder.
3. To connect, attach the Waves Maker to the Controller Box together with the waterproof
connector. Check the nut’s of the waterproof connector and tightened it.
4. Power transformer connected to AC power followed by, connecting the DC output line to
Controller box. Please check all cable connections are intact.
 Please Note: If you encounter problems with the equipment and the Control Box LED Flash,
Only Disconnect DC connector form Controller Box and reconnect after three seconds and
then system will start back to normal operation.
 Caution: Magnetic holder made of ultra-powerful magnets, must be handle with proper
care to Prevent injuries!
CONCH ADVANCE WAVE MAKER CONTROLLER
5. LCD Display
Display all adjustable functions and time information.
6. Function Key Panel
Different Mode Function control, pulse time adjust and Wireless setting buttons.
7. LED indicator
Display System action and the error message．
8. Wave Maker connector
Waves Maker pump waterproof connector
9. DC Power connector
DC power supply connector.
CONCH ADVANCE WAVE MAKER CONTROLLER BACK SIDE
10. Light Sensor
The back side of the control box with a Lights sensor, users can double-sided adhesive tape will be
fixed on the fish tank, and Lights sensors will face the luminosity within the induction aquarium (day
mode Half speed / night mode. Half speed).
．
11. Magic Velcro
For fixed the Controller.
12. Barcode sticker
Warranty basis on the serial number barcode.
Main Control Panel
1. Async / Sync / LongRun /Sequence 1>2>3>4 Button
Each system controller can be controlled via wireless, Can be set four groups, each group
can set up an unlimited number of Wave Makers. Run as synchronization / asynchronously
/ long run or Sequence 1>2>3>4 . Since the optimal functioning of the single Wave Maker
radius is 80cm, such as for aquarium width exceeding 80cm can be installed 2~4 sets Wave
Maker in the same direction to run synchronously, or 2~4 sets Wave Maker installed and set
to run asynchronously relative direction．
Each time Press ‘Mode’key can be to change synchronization / asynchronously / long Run
or Sequence 1>2>3>4.
(Fish tank for each user are different and the layout there are differences, so the user
should should itself aquarium environment settings)
2. Time Select
Under Sync / Async Mode, Press ‘Mode’key once time the display will be show in time
figures different locations flashing, from right to left (from 00.01 start)
Press the ‘up’ and ‘down’ keys to change 0-9, press the ‘Time Select’ key position and
move it to the left of the figures of the time using the up and down arrow keys to mobilize．
Under ‘Sequence 1>2>3>4’ Mode Press ‘Time Select’select M1 ~ M4 Wave Maker run time
using the up and down arrow keys to adjust the pause interval from 1 to 99 seconds, and
there will be two seconds between each made waves made waves this function 1st to 2nd
Wave Maker at least adjustment time for one second .3rd or 4th Wave Maker adjustable for
0 seconds 0 seconds will be treated, such as tone did not then between 3 rd to 4th Wave
Maker 2 seconds will be automatically deleted..
3. Press ‘Time Select’ Key hold 3seconds will goto ‘Auto Adjust’Mode, Press ‘Time
Select’ Key again to quit.
This function the system automatically will start by the set time had been add 0.01 seconds per
Canadian run five times, allowing users to see the effect and then press ‘Time Select’Key once
to stop automatic regulation. If the result is less than ideal, the available Select Time for finetuning. (Recommended to use the second wave: usually the first wave will soon appear, but the
effect is relatively stiff water less balanced, such as one meter fish tank fish tank about 0.64
seconds -1.5 m about 0.74 seconds time of the second wave of the first waves x2 for further
fine-tuning, more large force and effect and made waves box soft water can flow throughout the
fish tank.)
4. Effect & Feed Button Normal/Nature/Tidal/Reefs/Shallow/Feed
Press 'Effect & Feed' button mode can be changed into a Nature Effect, Nature to run the
simulation rules of nature, Tidal Effect to simulate the moon's tide and lead to low tide, but
the pulse duration pulse time regulator is still regulated by time prevail. Reefs Effect is base
on the flow pulse coral longer dwell time to increase the water flow to simulated coral reef
environment, Shallow Effect currents random pattern to make a special length delivery
nearshore turbulence effects.
When Tidal Effect, First time need to press Mode (Hold 3 seconds) to setup Tidal data.
'+' or '-' FullNoon day, 'Time'=real time, press Mode one time to select input. And press
Mode (Hold 3 seconds) to quit Tidal setup.
5. Press ‘Effect & Feed’ hold 3seconds goto Feed Mode, LCD show the feed time
Wave Maker will stop running for 10 minutes and the countdown time is displayed on the LCD,
the reply before feeding mode automatically after 10 minutes. Wave Maker stopped running the
meantime would like to reply to the previous mode, press the ‘Effect & Feed’ key 3 seconds you
can leave the feeding mode.
6. Motor Speed.
The key can be adjusted with the ‘up’ and ‘down’ keys to select Wave Maker power between
50%~100%.
7. Master Slave key, To setup Master or Slave.
Each channel systems can be set only one Master host and Slave1 - Slave4 each slave can
set infinite sets. Theoretically will be able to work properly as long as the effective wireless
range.
8. Wireless Channel key, Setup form 00~99 Channel.
Wireless signals may be affected by the interference of sympathy, in response to various
environmental set different channels to reduce interference to increase the stability of the
system.
9. Night Mode
Automatically go into night mode when the light sensor head no light irradiation system to
run at half speed, the display will appear as ‘Night’．
10. LED Indicator
Under normal circumstances working conditions made LED in red．
However, in Wave Maker pump problem occurs, the indicator will be displayed flashes red,
User should turn off the power and check the relevant examination methods Please refer to
the maintenance section.
Maintenance and repair:
Error Table
Power
Control Box
Supply LED
LED
Wave Maker
ON
ON
RUNNING
RUNNING NONON
ON
NORMAL
ON
ON
NOT RUN
ON
ON
OFF
FLASH
OFF
OFF
NOT RUN
NOT RUN
NOT RUN
Normal
Check Impeller Stuck or Control Box
Check Water Proof Connector Between Control Box and Wave Maker
# Check Impeller Stuck and Water Proof Connector Between Control Box and
Wave Maker
* Either Power Supply or Control Box Problem
* Power Supply Problem
## Before Check and Clean the System, Disconnect the Connector Between Control Box and Power Supply First.
# After Check and Clean. Re-connect the Connector Between Control Box and Power Supply, System will Running Normally.
* Send to Dealer check, After confirm which parts problem then send it with warranty card to our service center.
If you encounter problems with the equipment and the indicator blinks RED light, Only pull out DC
connector form Controller Box and reconnect after three seconds and then system will start back to
normal operation.
Steps to be taken, in the event the system fails to operate and wave lights still flashing on the Controller
Box:
11.
Check the power supply and the controller box for the indicator lights, as it should be ON.
If the lights are ON, the power supply and the controller is in working condition. If there is no
indicator light on the controller box, the power supply or the controller box is faulty.
You should send your equipment back to the local distributor or dealer for servicing.
12. If there is electric supply, unplug the power supply, and check the Wave Maker’s Impeller.
Clean the impeller and turn the propeller by hand to check the rotation is working normal.
Reconnect the power to Controller Box, after three seconds then it should perform to its normal
operating system