INTRODUCTION
The water level indicator employs a simple mechanism to detect and indicate
the water level in a tank or any other container. The level sensing is done by a
pair of probes, the resistance between which depends upon the water level in the
tank. These probes can be placed in two ways on the walls of the tank or
container
The purpose of the water level indicator is to caution a person that a water tank
has been filled up to a particular level. This circuit exploits the simple fact that
water is a good conductor of electricity. The system is capable of indicating the
water level in two ways- visual (by the means of an LED) and audible (by the
means of a sound generated by a piezoelectric buzzer). The placement of two
probes (with connections from the circuit) inside the water tank determines the
minimum detectable level (MDL). When the water reaches this height in the
tank (or any other fluid container), the buzzer is activated and the LED is turned
on. Number of ICs used: None.
Working:
1. Both the probes can be placed at different points on the wall lying at the same
level/height from the bottom. This height determines the minimum detectable
water level, or
2. The probes can be placed at different points lying at two different heights
from the tank bottom. In this case, the probe which is placed higher than the
other determines the minimum detectable water level.
When the water-level is below the minimum detectable level (MDL), there is
infinite impedance between the two probes. Hence, transistor T2 remains in the
cut-off mode and does not conduct. However when water-level reaches MDL or
is above it, the connection between the probes gets completed (through the
conducting medium o water) and the base voltage of T2 increases. This causes
the base-emitter junction of T2 to get forward biased and the piezoelectric
buzzer is turned on to generate an alarm sound. The path from the emitter of T2
through resistance R3 is responsible for forward biasing the base of transistor
T1. This switches T1 from cut-off to conduction mode, thereby driving the red
LED to glow. Hence at each instance when water reaches the MDL, both the
buzzer and LED indicate this simultaneously.
CIRCUIT DIAGRAM
PART LIST:
Semiconductors:
T1 - BC547 transistor
T2 - BC107 transistor
D1 - 1N4003
D2 - Red LED
Resistors (all ¼-watt, ±5% carbon):
R1 - 470 kilo-ohm
R2 - 220 ohm
R3 - 3.3 kilo-ohm
Capacitors
C1
- 50μF (or 47μF), 16V
Piezoelectric Buzzer
Printed Circuit Board (PCB
COMPONENT DESCRIPTION
Diode:
There is a lot of confusion in text books and on the web about CURRENT
FLOW.
WHICH WAY DOES CURRENT FLOW?
Current is a flow of electrons. These electrons are negatively charged particles
and they are attracted to the POSITIVE of the supply. This means they flow
from NEGATIVE to POSITIVE.
The first inventors and discoverers of electricity did not know this.
They thought electricity flowed from POSITIVE to NEGATIVE. So, they made
a CONVENTION (statement) that electricity (CURRENT) flows from
POSITIVE to NEGATIVE.
They were wrong. But hundreds of text books had already been written, so we
have TWO situations.
The answer is simple.
When we discuss electrical and electronic circuits, we use the old convention,
called CONVENTIONAL CU When discussing ELECTRON-FLOW we use
NEGATIVE to POSITIVE.
We keep ELECTRON FLOW arrows within the component we are talking
about (such as a radio-valve or transistor-model) and do not put electron-flow
arrows on the rest of the circuit.
We have to do this to prevent CONFUSION.
Here is the answer:
Don't use any text-books that say current flow is electron-flow as they are
omitting CONVENTIONAL CURRENT FLOW and this will confuse you.
We are discussing this point because a diode is an ELECTRONIC device. In
other words it involves the flow of electrons because CURRENT will only flow
in one direction through a diode.
In all of our discussions we have used CONVENTIONAL CURRENT FLOW
as we are talking to beginners in electronics and not PHYSICS students.
A diode is a very simple device and it has a lot of applications. We will cover
some of its uses and explain exactly how it works in very simple terms.
A diode is a device that passes current in only one direction. It is a bit like a
water-valve that prevents water back-flowing into the mains from your
property. Or a valve in a pump that prevents the water flowing back down a
well.
There are many types of diodes to handle small currents, large currents, high
frequencies and high voltages. And there are diodes made from different
materials, but they can all be described in a simple way. And that's what we will
do.
A diode has two leads. These are called ANODE and CATHODE.
The cathode end is identified in a circuit diagram and on the body of the device.
It may be identified with a line, chamfer or dimple or a symbol. There must be
something on the diode that identifies this lead and you have to look for it.
A diode does NOT have a positive or negative end. You see this mistake in so
many discussions. A diode will have a positive voltage on the anode and a
slightly lower (positive) voltage on the cathode. It will not have a positive on
the anode and negative on the cathode.
Incorrect marking with "+" and "-"
In the following diagram only the CATHODE is identified with the letter k (for
kathode). The other lead is the ANODE.
Correct marking with "k"The most common type of diode is made from
SILICON. It can also be made from GERMANIUM. You need to look in the
datasheet to find the composition of the diode you are using.
A diode does not "turn on" or "conduct" until a small voltage is present on its
ANODE END.
As mentioned above, a diode does not start to TURN ON until a small voltage is
present on its ANODE lead.
For a Germanium diode, this voltage is approx 0.3v.
For a Schottkey diode, this voltage is 0.3v
For a Silicon diode, this voltage is 0.7v.
LEDS
A LED lamp is a light-emitting diode (LED) product that is assembled into a
lamp (or light bulb) for use in lighting fixtures. LED lamps have a lifespan and
electrical efficiency that is several times better than incandescent lamps, and
significantly better than most fluorescent lamps, with some chips able to emit
more than 100 lumens per watt.
Like incandescent lamps and unlike most fluorescent lamps (e.g. tubes and
CFL), LED lights come to full brightness without need for a warm-up time; the
life of fluorescent lighting is also reduced by frequent switching on and off.
Initial cost of LED is usually higher. Degradation of LED die and packaging
materials reduces light output to some extent over time.
With research into organic LEDs (OLED) and polymer LEDs (PLED), cost per
lumen and output per device have been improving so rapidly according to what
has been called Haitz's law, analogous to Moore's law for semiconductor
devices.
Some LED lamps are made to be a directly compatible drop-in replacement for
incandescent or fluorescent lamps. An LED lamp packaging may show the
lumen output, power consumption in watts, color temperature or description
("warm white") and sometimes the equivalent wattage of an incandescent lamp
of similar luminous output.
LEDs do not emit light in all directions, and their directional characteristics
affect the design of lamps. The light output of single LEDs is less that that of
incandescent and compact fluorescent lamps; in most applications multiple
LEDs are used to form a lamp, although high-power versions (see below) are
becoming available.
LED chips need controlled direct current (DC) electrical power; an appropriate
power supply is needed. LEDs are adversely affected by high temperature, so
LED lamps typically include heat dissipation elements such as heat sinks and
cooling fins.
RESISTORS
A resistor is a passive two-terminal electrical component that implements
electrical resistance as a circuit element.
The current through a resistor is in direct proportion to the voltage across the
resistor's terminals. This relationship is represented by Ohm's law:
Where I is the current through the conductor in units of amperes, V is the
potential difference measured across the conductor in units of volts, and R is the
resistance of the conductor in units of ohms.
The ratio of the voltage applied across a resistor's terminals to the intensity of
current in the circuit is called its resistance, and this can be assumed to be a
constant (independent of the voltage) for ordinary resistors working within their
ratings.
Resistors are common elements of electrical networks and electronic circuits
and are ubiquitous in electronic equipment. Practical resistors can be made of
various compounds and films, as well as resistance wire (wire made of a highresistivity alloy, such as nickel-chrome). Resistors are also implemented within
integrated circuits, particularly analog devices, and can also be integrated into
hybrid and printed circuits.
The electrical functionality of a resistor is specified by its resistance: common
commercial resistors are manufactured over a range of more than nine orders of
magnitude. When specifying that resistance in an electronic design, the required
precision of the resistance may require attention to the manufacturing tolerance
of the chosen resistor, according to its specific application. The temperature
coefficient of the resistance may also be of concern in some precision
applications. Practical resistors are also specified as having a maximum power
rating which must exceed the anticipated power dissipation of that resistor in a
particular circuit: this is mainly of concern in power electronics applications.
Resistors with higher power ratings are physically larger and may require heat
sinks. In a high-voltage circuit, attention must sometimes be paid to the rated
maximum working voltage of the resistor. While there is no minimum working
voltage for a given resistor, failure to account for a resistor's maximum rating
may cause the resistor to incinerate when current is run through it.
Practical resistors have a series inductance and a small parallel capacitance;
these specifications can be important in high-frequency applications. In a lownoise amplifier or pre-amp, the noise characteristics of a resistor may be an
issue. The unwanted inductance, excess noise, and temperature coefficient are
mainly dependent on the technology used in manufacturing the resistor. They
are not normally specified individually for a particular family of resistors
manufactured using a particular technology. A family of discrete resistors is
also characterized according to its form factor, that is, the size of the device and
the position of its leads (or terminals) which is relevant in the practical
manufacturing of circuits using them.
CAPACITORS:
A capacitor (originally known as a condenser) is a passive two-terminal
electrical component used to store energy electrostatic ally in an electric field.
The forms of practical capacitors vary widely, but all contain at least two
electrical conductors separated by a dielectric (insulator); for example, one
common construction consists of metal foils separated by a thin layer of
insulating film. Capacitors are widely used as parts of electrical circuits in many
common electrical devices.
When there is a potential difference across the conductors, an electric field
develops across the dielectric, causing positive charge to collect on one plate
and negative charge on the other plate. Energy is stored in the electrostatic field.
An ideal capacitor is characterized by a single constant value, capacitance. This
is the ratio of the electric charge on each conductor to the potential difference
between them. The SI unit of capacitance is the farad, which is equal to one
coulomb per volt.
The capacitance is greatest when there is a narrow separation between large
areas of conductor, hence capacitor conductors are often called plates, referring
to an early means of construction. In practice, the dielectric between the plates
passes a small amount of leakage current and also has an electric field strength
limit, the breakdown voltage. The conductors and leads introduce an undesired
inductance and resistance.
Capacitors are widely used in electronic circuits for blocking direct current
while allowing alternating current to pass. In analog filter networks, they
smooth the output of power supplies. In resonant circuits they tune radios to
particular frequencies. In electric power transmission systems they stabilize
voltage and power flow.
A capacitor consists of two conductors separated by a non-conductive region.
The non-conductive region is called the dielectric. In simpler terms, the
dielectric is just an electrical insulator. Examples of dielectric media are glass,
air, paper, vacuum, and even a semiconductor depletion region chemically
identical to the conductors. A capacitor is assumed to be self-contained and
isolated, with no net electric charge and no influence from any external electric
field. The conductors thus hold equal and opposite charges on their facing
surfaces, and the dielectric develops an electric field. In SI units, a capacitance
of one farad means that one coulomb of charge on each conductor causes a
voltage of one volt across the device.
An ideal capacitor is wholly characterized by a constant capacitance C, defined
as the ratio of charge ±Q on each conductor to the voltage V between them.
Because the conductors (or plates) are close together, the opposite charges on
the conductors attract one another due to their electric fields, allowing the
capacitor to store more charge for a given voltage than if the conductors were
separated, giving the capacitor a large capacitance.
Sometimes charge build-up affects the capacitor mechanically, causing its
capacitance to vary. In this case, capacitance is defined in terms of incremental
changes:
9-0-9 TRANSFORMER
AC-240VtoAC-9V
RM0513 is a general purpose chassis mounting mains transformer. Transformer
has 240 V primary windings and centre tapped secondary winding. The
transformer has flying colored insulated connecting leads (Approx 100 mm
long). The Transformer act as step down transformer reducing AC- 240 V
to
AC 9V.
The Transformer gives two outputs of 18 V, 9 V and 0 V. The Transformer’s
construction is written below with details of Solid Core and
Winding.
The transformer is a static electrical device that transfers energy by inductive
coupling between its winding circuits. A varying current in the primary winding
creates a varying magnetic flux in the transformer's core and thus a varying
magnetic flux through the secondary winding. This varying magnetic
flux induces a varying electromotive force (E.M.F) or voltage in the secondary
winding. The transformer has cores made of high permeability silicon steel. The
steel has a permeability many times that of free space and the core thus serves
to greatly reduce the magnetizing current and confine the flux to a path which
closely couples the windings.
The solid core uses one of the common design of laminated core is made from
interleaved stacks of E - shaped steel sheets capped with I - shaped pieces,
leading to its name of 'E - I transformer’. Such a design tends to exhibit more
losses, but is very economical to manufacture.
Windings are arranged concentrically to minimize flux leakage. The effect of
laminations is to confine eddy currents to highly elliptical paths that enclose
little flux, and so reduce their magnitude. Thinner laminations reduce losses, but
are more laborious and expensive to construct. Thin laminations are generally
used on high-frequency transformers, with some of very thin steel laminations
able to operate up to 10 KHz.
PCB FABRICATION
The first step of assembling is to produce a printed circuit board. The
fabrication of the program counter plays a crucial role in the electronic field.
The success of the circuit is also dependent on the PCB. As far as the cost is
concerned, more than 25% of the total cost is for the PCB design and
Fabrication.
The board is designed using a personal computer. The layout is drawn using the
software “Adobe PageMaker 6.5”. The layout is printed in a “buffer sheet”
using a laser procedure. First, a negative screen of the layout is prepared with
the help of a professional screen printer. Then the copper clad sheet is kept
under this screen. The screen printing ink is poured on the screen and brushed
through the top of the screen. The printed board is kept under shade for few
hours till the ink becomes dry.
The etching medium is prepared with the un-hydrous ferric chloride water. The
printed board is kept in this solution till the exposed copper dissolves in the
solution fully. After that the board is taken out and rinsed in flowing water
under a tap. The ink is removed with solder in order to prevent oxidation.
Another screen, which contains component side layout, is prepared and
the same is printed on the component side of the board. A paper epoxy laminate
is used as the board. Both the component and the track layout of the peripheral
PCB is given at the end of this report
© Copyright 2026 Paperzz