A2 1000 Series
Aktra II Cutoff Floodlight, 1000W HID
Type:
Job:
Approvals:
Catalog Number:
-
Series/Source -Wattage
-
Optics
(Reflector)
-
Voltage
Overall Dimensions
-
Mounting
For Reference Only
Options
(Factory Installed)
Finish
Accessories
(Field Installed)
Date:
Page 1 of 6
Specifications
Housing
Mastfitter Mount (M)
Side View
-
The Aktra II 1000 floodlight features a cast aluminum alloy housing with integral heat
dissipating fins and heavy-duty hinges. Standard unit constructed to IP54.
30.0”
(76.2cm)
Optics (Reflector)
17.75”
(45.09cm)
4”
(10.16cm)
Aktra reflector system. High purity anodized aluminum reflectors assure maximum efficiency.
A secondary internal reflector element reflects high angle rays back into the beam to
achieve high beam utilization. Meets IES definition of cutoff distribution.
Lamp Access
Hinged lens frame allows convenient lamp access.
Lens
End View
Clear tempered glass lens is secured to cast aluminum door frame by 10 retaining clips and
sealed with a gasket.
19.75”
(50.17cm)
Socket
Pre-wired grip-type mogul base socket, 4KV rated for MH, 5KV for HPS. Glass end of the
lamp is held in precise photometric alignment and protected from breakage by a Stabilux
socket.
Ballast
High power factor ballast with reliable starting down to -29°C (-20°F) for Metal Halide
lamps, -34°C (-30°F) for Pulse Start Metal Halide lamps, and -40°C (-40°F) for High
Pressure Sodium. Ballast has Class H, 180°C (356°F) rated insulation. Crest factor does
not exceed 1.8. Capacitor and HPS ignitor are separated from the ballast core and coil to
maximize life by minimizing heat.
22.5”
(57.15cm)
Lens
Aiming
22.5”
(57.15cm)
Cutoff distribution achieved at 62.5° (2 times mounting height). Aiming above 63° provides
semi-cutoff and non-cutoff distribution.
Mounting
Fixture may be specified with a cast aluminum mastfitter, suitable for mounting to a 2-3/8”
O.D. vertical tenon; or formed plate steel yoke. Yoke mount allows mounting directly to any
flat surface.
Yoke Mount (Y)
Side View
Finish
31.0”
(78.74cm)
Standard finish shall be dark bronze UltraClad polyester powder coating, 2.5 mil nominal
thickness, electrostatically applied and oven cured. All components shall be thoroughly
cleaned by a 5 stage pre-treatment process including iron phosphate bath and non-chromic
acid etching stages, ensuring optimum performance characteristics. Other colors may be
specified.
30.0”
(76.2cm)
17.75”
(45.09cm)
5.0”
(12.7cm)
Listings
ETL/cETL listed to the UL 1598 standard, suitable for Wet Locations. The quality systems of
this facility have been registered by UL to the ISO 9001 Series Standards.
Warranty / Terms and Conditions
Bottom View - Yoke Mount, see page 5 for details.
Gardco luminaires feature a 5 year limited warranty. See Warranty Information on
www.sitelighting.com for complete details and exclusions. Polycarbonate lenses carry a 1
year warranty only.
Some luminaires use fluorescent or high intensity discharge (HID) lamps that contain small
Hg amounts of mercury. Such lamps are labeled ‘Contain Mercury’ and/or with the symbol ‘Hg’.
Weight 96 lbs (43.54 kgs)
EPA data shown on page 3.
© 2013 Koninklijke Philips Electronics N.V. All rights reserved.
Specifications are subject to change without notice.
G200-118/0313
Lamps that contain mercury must be disposed of in accordance with local requirements.
Information regarding lamp recycle and disposal can be found at www.lamprecycle.org.
A2 1000 Series
Aktra II Cutoff Floodlight, 1000W HID
Type:
Job:
Page 2 of 6
Series/Source-Wattage
Metal Halide
Voltage
Optics (Reflector)
r A
r A2M-1000
r C
Pulse Start
r M r 208
(Standard)
r Y Yoke Mount
Mastfitter Mount
r 277
r 480
High Pressure Sodium
r QV(2)
r A2S-1000
(1) For acceptable performance, note position orientation specific nature of
Pulse Start lamps. Consult factory.
Options (Factory Installed)
r 120
r 240
r D
r A2P-1000 (1)
Mounting
(2) Allows field selection of 120/208/240/277 voltage. (No 480V). Certain
options may require voltage selection as well.
Finish
Accessories (Ordered Separately)
r BL Bi-Level dimming
r TDB
Textured Dark Bronze
r F1-KIT
Single Fuse Kit (120/277V)
r CSR
Hot Quartz Restrike
r TGR
Textured Gray
r F2-KIT
Double Fuse Kit (208/240/480V)
r LQ
Hot/Cold Quartz Restrike
r TBK
Textured Black
r PX-1-TL r LQ1
Separately Wired (120V) Quartz Restrike
r F1 r TWHT
Textured White
Heavy-Duty Cross Arm bracket with 2-3/8” pipe stub,
Galvanized finish
Single Fuse (120/277V)
Double Fuse (208/240/480V)
Textured Satin Aluminum
r FB-1-TL
r F2 r TSA
Heavy-Duty Flat Base mount,
Galvanized finish
r TLR Twist Lock Receptacle (photocell by others)
r TGN
Textured Green
r AL-10-A2
Auxiliary Polymer Lens
r 50HZ 50 Hz ballast operation
r A2-AIM
A2 Aiming Device
r WB-1
Wall bracket for mounting to flat vertical surface (bullhorn)
r WB-5
Surface Mounted Wiring box
r PM-1-HD
Heavy-Duty Wood pole mounting kit for single fixture with one U-arm
r PM-2-HD
Heavy-Duty Wood pole mounting kit for two fixtures with two U-arms
r PM-3-HD
Heavy-Duty Wood pole mounting kit for three fixtures with three U-arms
r PM-4-HD
Heavy-Duty Wood pole mounting kit for four fixtures with four U-arms
r RAL(*)
Special Tiger Drylac powdercoat finish (*) = specify color
(*) Specify RAL color number from
RAL color chart. Consult factory for
assistance in color selection.
© 2013 Koninklijke Philips Electronics N.V. All rights reserved.
Specifications are subject to change without notice.
www.philips.com/luminaires
G200-118/0313
A2 1000 Series
Aktra II Cutoff Floodlight, 1000W HID
Type:
Job:
Page 3 of 6
Distribution Guide & Ballast Data 1
Source
Type(2)
Catalog
Number
Reflector Lamp(3)
Field Angle
Beam Angle
Type Envelope Based on 10% Based on 50%
.ies
File Name
Ballast
Type (4)
ANSI
Code
Line Current
Line
120 / 208 / 240 / 277 / 480 Watts
MH
A2M-1000
A2M-1000
A2M-1000
A
C
D
BT37
BT37
BT37
129H x 22V
103H x 90V
80H x 28V
75H x 8V
62H x 27V
53H x 14V
a2m100a.ies
a2m100c.ies
a2m100d.ies
CWA
CWA
CWA
M47 / H36
M47 / H36
M47 / H36
9.2 / 5.6 / 4.7 / 4.1 / 2.4
9.2 / 5.6 / 4.7 / 4.1 / 2.4
9.2 / 5.6 / 4.7 / 4.1 / 2.4
1080
1080
1080
PS
A2P-1000
A2P-1000
A2P-1000
A
C
D
BT37
BT37
BT37
129H x22V
103H x 90V
80H x 28V
75H x 8V
62H x 27V
53H x 14V
a2p100a.ies
a2p100c.ies
a2p100d.ies
CWA
CWA
CWA
M141
M141
M141
9.0 / 5.2 / 4.5 / 3.9 / 2.4
9.0 / 5.2 / 4.5 / 3.9 / 2.4
9.0 / 5.2 / 4.5 / 3.9 / 2.4
1080
1080
1080
HPS
A2S-1000
A2S-1000
A2S-1000
A
C
D
E25
E25
E25
117H x 20V
100H x 89V
90H x 72V
62H x 7V
60H x 28V
63H x 14V
a2s100a.ies
a2s100c.ies
a2s100d.ies
CWA
CWA
CWA
S52
S52
S52
9.5 / 5.5 / 4.8 / 4.2 / 2.5
9.5 / 5.5 / 4.8 / 4.2 / 2.5
9.5 / 5.5 / 4.8 / 4.2 / 2.5
1100
1100
1100
(1) The Aktra II 1000 accommodates a variety of other
wattages and lamps. Consult factory.
(2) MH = Metal Halide, PS = Pulse Start Metal Halide, HPS
= High Pressure Sodium.
(3) Horizontal clear lamps recommended for optimum
photometric performance.
(4) CWA = Constant Wattage Autotransformer.
Distribution Patterns
Photometric data calculated at 50’ mounting height.
A2M-1000-A
A2M-1000-C
0MH 1MH 2MH 3MH
0MH
Z
0° P
LA
NE
°
90
P
X
L
A
CE AIM
NT ING
ER
LIN
E
N
3
E
2
1
.5
.25
2MH
1
.5
3MH
.25
A2S-1000-C
0MH 1MH 2MH 3MH
1MH
1
.5
.25
EPA
Effective Projected Area in Ft2
3.4
© 2013 Koninklijke Philips Electronics N.V. All rights reserved.
Specifications are subject to change without notice.
www.philips.com/luminaires
G200-118/0313
2MH
3MH
3
2
1
.5
.25
4MH
1MH
3
2MH
2
3MH
1
.5
.25
4MH
A2S-1000-D
0MH 1MH 2MH 3MH
0MH
3
2
0MH
1MH
3
2
4MH
A2S-1000-A
0MH 1MH 2MH 3MH
0MH
1MH
Y
A2M-1000-D
0MH 1MH 2MH 3MH
2MH
3MH
4MH
0MH 1MH 2MH 3MH
0MH
0MH
1MH
1MH
2MH
3MH
4MH
3
2MH
2
.5
1
3MH
.25
4MH
A2 1000 Series
Aktra II Cutoff Floodlight, 1000W HID
Type:
Job:
Page 4 of 6
Option details (Factory Installed)
BL = Bi-Level
Note: Suitable for HPS in any aiming
position. Consult factory when specifying
dimming with Metal Halide.
Bi-Level provides high/low level
of lamp output with 50% power
consumption. Zero crossover
network avoids strobing and
lamp dropout.
CSR = Hot Quartz Restrike
CSR - Quartz restrike using a current sensing relay; extinguishes auxiliary lamp when main arc
strikes.
LQ = Hot/Cold Quartz Restrike
LQ - Provides LiteMatic operation for fixtures with 120V or multi-tap ballasts.
LQ1 - Separately wired, externally controlled emergency lighting from a separate power
source.
LQ1 = Separately Wired (120V) Quartz Restrike
LiteMatic Operation
Note: Standard 150 watt (120V)
double contact bayonet base socket.
Combined Quartz wattage may not
exceed HID lamp wattage.
Normal
Start: Main
and Quartz
lamps both
energized.
LQ1 requires an Interlock (by others) to
ensure HID and Quartz source are not
operated at once.
F1 = Single Fuse (120V/277V)
Main Lamp Reaches
Approximately 40% of
Rated Output: Quartz lamp
automatically extinguishes
(combined lamp currents
never exceed that of main
lamp at 100% output).
When Arc
Extinguished:
Auxiliary
quartz lamp
automatically
energized when
power is restored.
Main Lamp
Reaches 40% of
Rated Output:
Quartz lamp
automatically
extinguishes
Consists of 1 or 2 fuse holders
and 1 or 2 KTK 30 amp fuses.
F2 = Double Fuse (208V/240V/480V)
Note: If ordering QV ballast, voltage must
be specified.
TLR = Photocontrol Receptacle
Photocontrol twistlock receptacle only (Photocontrol by others).
50 HZ = 50 Hz Ballast Operation (Consult Factory)
Specified for applications (outside the United States) where 50 Hertz
operation is standard.
Accessory details (Field Installed - Shipped Separately)
F1 Kit = Single Fuse Kit (120V/277V)
F2 Kit = Double Fuse Kit (208V/240V/480V)
PX-1-TL = Heavy duty Cross-arm Bracket
4.75”
4.5”
1.5”
1.375”
Consists of 1 or 2 fuse holders and
1 or 2 KTK 30 amp fuses.
Steel angle bracket with
2” pipe stub. Four gussets
provide additional mounting
stability.
“L” base.
Hot dipped galvanized.
For installing floodlights on
wooden or steel cross-arms.
1.875”
Top View
Front View
© 2013 Koninklijke Philips Electronics N.V. All rights reserved.
Specifications are subject to change without notice.
www.philips.com/luminaires
G200-118/0313
6.25”
2-3/8” O.D.
PipeTenon
(15.88cm)
11”
(27.94cm)
4.5”
9/16”
Dia. Hole
(5 Places
Typical)
(11.43cm)
6”
(15.24 cm)
3.63”
(15.88cm)
A2 1000 Series
4
2
Aktra II Cutoff Floodlight, 1000W HID
3
Type:
1
REV
Job:
DESCRIPTION
DATE
BY
A
1.90 WAS 1.55, 3.80 WAS 3.10, ADDED LABELS (2X)
12-10-92
LAB
B
MODELLEDANDREDRAWNSW,REPLACED2LABELS
WITHSINGLELABELPN523908,ADD"5005H34"TOMATL.
SPEC, CHARTED ASSEMBLY, ADD ASSY WIP 523959
5-8-08
McA
PCN#
CHK BY
20324
CF 5-12-08
Page 5 of 6
Accessory details continued (Field Installed - Shipped Separately)
12.00
FB-1-TL = Flat Base Mount
Steel construction, with 2” pipe stub
and four gussets for heavy-duty
support.
6.00
9.38
6.25”
(15.88cm)
3.80
For installing
.25 (3X) floodlight to flat horizontal surfaces.
1.90
A
10.5” sq.
(26.67cm)
.50
B
2
11.75” sq.
(29.85cm)
1.50
SEENOTE
1AND2
BENDUP65°
AL-10-A2
= Auxiliary Polymer Lens
Auxiliary lens for Aktra II Series floodlights.
PART NO. 523908
O
W
N
Aiming device can be sighted from either
side of the fixture. See Installation Instructions
for details.
BE
N
0°
D
W
N
A2-AIM
= A2 Aiming Device
9
90
°
.
D
D
O
AIMING DEVICE MOUNTED
RIGHT SIDE OF FIXTURE
SIGHT THRU THIS HOLE
N
D
AIMING DEVICE MOUNTED
LEFT SIDE OF FIXTURE
SIGHT THRU THIS HOLE
.
BE
C
2.16
1/4” thick impact-resistant polymer lens,
45°
furnished with mounting hardware and
135°
standoffs.
Provides additional protection of the glass
lens. Useful life is limited by UV discoloration
from sunlight, mercury or metal halide
lamps.
°
17/32"
Dia.
Hole
(4 Places
Typical)
Hot dipped galvanized.
4.69
D
2-3/8” O.D.
Pipe Tenon
B
WB-1 = Wall Bracket (Bullhorn)
N
W
N
APPLYLABELTOAIMINGDEVICEAFTERITISFORMED.
Use in conjunction with WB-5 for surface 1.
2-3/8”
2. OBSERVEPROPERORIENTATIONOFLABELANDALIGN
ARROWSWITHHOLESASSHOWN
mounted wiring.
Pipe
O
W
90
°
1.69
.56
.50
1.34
Used in conjuntion with WB-1 for surface SYM
CL
conduit feed. Tapped top, back
and EXCEPT
bottom for 3/4” pipe or conduit.
LABEL
4
1.81
5.63”
ITEM NO. (14.29cm)
PART NO.
1
505709
square
2
523908
.67
WB-5 = Surface Mounted Wiring Box
NOTE:
90
°
BENDUP90°
(21.59cm)
(4 Places
T ypical)
D
D
O
8.50”
9/16”
Dia. Hole
D
N
D
BE
N
BE
.12
90.00°
Cast aluminum wall bracket for vertical
surfaces only. Designed to permit
7.50
mounting of floodlights on flat vertical
surfaces.
3DVIEWSHOWN
FORREFERENCEONLY
NOTTOSCALE
DONOTSCALETHISDRAWING
DWNBY
DATE
CHK BY
DATE
APPROVED BY
DATE
LAB
3/4” NPT
CF
(Top, Bottom and Back)
Cast aluminum wall bracket for vertical
surfaces only. Designed to permit
mounting of floodlights on flat vertical
surfaces.
UNLESSOTHERWISESPECIFIED:
Dimensions are in inches
andtolerancesare:
.03
.XX±________
.005
.XXX±________
1°
ANGLES±________
.015THRU6INCHES
FRACTIONS±________
Machine Surface
Use in conjunction with WB-5 for surface
CONTROLLED DOCUMENT
mounted wiring.
Check ERP System Screen
for Latest Revision
3
Tenon
DESCRIPTION
QTY
(5” useable
AIMING,DEVICE-A2-1000 length) 1
LABEL,A2-1000-AIMING-DEVICE
1
Roughnesstobe:
6.88”
125
(17.46cm)
square
NOTE:DoNotScaleDrawing
THE INFORMATION CONTAINED ON THIS
DRAWING IS THE EXCLUSIVE PROPERTY
OF WIDE-LITE, AND MAY NOT BE COPIED,
COMMUNICATED OR USED BY ANYONE
WITHOUT THE EXPRESS PREMISSION OF
AUTHORIZED WIDE-LITE PERSONNEL.
AE
8-12-92
Wiring
Inspection
Plate
P.O.
BOX 606 (78667)
5-8-08
5-8-08
.032 THICK
ALUMINUM
5005 H34 B
SCALE
PHONE512-392-5821FAX512-753-1172
NAME
Pt.No.
1:1
523959
2
AIMINGDEVICE
A2-1000
ASSEMBLED WITH LABEL
DWGNO.
B
3.25" Deep
PAGE
(8.25cm)
C-17001
1 OF 1
1
Galvanized steel heavy-duty wood pole mounting kits are suitable for mounting up to four luminaires
with mastfitters to 6.0”-12.0” O.D. wood poles. Shipped as components for field assembly.
PM-1-HD Heavy-duty wood pole mounting kit for single luminaire, with 1 U-arm
shipping weight: 15 lbs (6.80 kgs)
PM-2-HD Heavy-duty wood pole mounting kit for two luminaires, with 2 U-arms
PM-1-HD
shipping weight: 20 lbs (9.07 kgs)
PM-2-HD
PM-3-HD Heavy-duty wood pole mounting kit for three luminaires, with 3 U-arms
shipping weight: 26 lbs (11.79 kgs)
PM-4-HD Heavy-duty wood pole mounting kit for four luminaires, with 4 U-arms
shipping weight: 31 lbs (14.06 kgs)
© 2013 Koninklijke Philips Electronics N.V. All rights reserved.
Specifications are subject to change without notice.
www.philips.com/luminaires
G200-118/0313
12.0” (30.48cm)
2-3/8” O.D. tenon
(typical)
PM-3-HD
A
1611 CLOVIS R. BARKER ROAD
SANMARCOS,TX78666
MATERIAL
PM-4-HD
REV
B
A2 1000 Series
Aktra II Cutoff Floodlight, 1000W HID
Type:
Job:
Page 6 of 6
Yoke Mount detail
5.0”
(12.70cm)
Bottom View
0.56” Dia.
(1.42cm)
CL
0.75”
(1.90cm)
2.5”
(6.35cm)
3.5” Radius
(8.89cm)
5.0”
(12.70cm)
CL
Direction of
Major Light
Path
0.56”
(1.42cm)
3.5”
(8.89cm)
0.75”
(1.90cm)
Notes
© 2013 Koninklijke Philips Electronics N.V. All rights reserved.
Specifications are subject to change without notice.
G200-118/0313
Philips Lighting Company
200 Franklin Square Drive
Somerset, NJ 08873
Phone: 855-486-2216
Philips Lighting Company
281 Hillmount Road
Markham ON, Canada L6C 2S3
Phone: 855-486-2216
www.philips.com/luminaires
www.philips.com/luminaires