TABLE OF CONTENTS
CHAIN SLING USAGE ····················································································2, 3
ORDERING SLINGS AND CHAIN STYLES ·······················································4
GRADE 80 WORKING LOAD LIMITS······························································5, 6
GRADE 80 CHAIN AND ATTACHMENTS······················································7-17
EUROPEAN GRADE 80 CHAIN ATTACHMENTS ·······································18-23
GRADE 100 CHAIN AND ATTACHMENTS··················································24-33
GRADE 120 CHAIN ADVANTAGES, ATTACHMENTS································34-35
ENDURANCE HIGH PERFORMANCE CHAIN ·················································36
COIL CHAIN, DOUBLE LOOP CHAIN··························································37-39
MISCELLANEOUS CHAIN, CHAIN HOOKS, ATTACHMENTS ···················40-50
PROOF COIL·································································································51-55
TIE DOWNS, BINDER CHAIN·······································································56-58
GRADE 70 CHAIN AND HOOKS·······································································59
BINDERS······································································································60, 64
1
CHAIN USAGE
ASME B30.9c-2000
Standards on Alloy Steel Chain Slings
Selection, Use, and Maintenance
These Specifications apply to slings made from Grade
80 alloy chain manufactured and tested in accordance
with NACM Welded Steel Chain Specifications —1990. If
chain other than that is used, it shall be used in accordance with the
recommendations of the manufacturer of the chain.
Rated Loads of Alloy Steel Chain Slings
Rated loads for alloy steel chain slings shall conform to
the values shown in Table 1 of the ASME SP. B30.9
Standards on Alloy Steel Chain Slings, Section ASME
B30.9c-2000. Rated loads shown in Table 1 are based
on a design factor of 4.
Sling Identification
Alloy steel chain slings covered by this Standard shall
have permanently affixed durable identification stating
size, manufacturer’s grade, rated load and angle upon
which the rating is based, reach, number of legs, and
sling manufacturer.
Effects of Environment
When the chain sling becomes heated to a temperature
in excess of 600º F (316º C), rated loads shall be reduced in accordance with the chain manufacturer’s recommendations regarding usage both while heated and
after being heated. The chain manufacturer should be
consulted when chain slings are to be used in temperatures of –40º F (–40º C) or below. The strength of slings
can be affected by chemically active environments as
sling materials may be susceptible to damage from
caustic or acid substances or fumes; strongly oxidizing
environments attack all common sling materials. The
manufacturer should therefore be consulted before
slings are used in chemically active environments.
Attachments
Hooks, rings, oblong links, pear–shaped links, welded or
mechanical coupling links or other attachments shall
have a rated load at least equal to that of alloy steel
chain with which they are used. In those special cases
where particular usage
makes this impractical, the sling shall be marked with a
rated load consistent with the least working load rating of
any component.
Standard attachments should be of a size recommended
by the sling manufacturer. All welded components in the
sling assembly shall be proof load tested as components
or as part of the sling assembly.
Makeshift fasteners, hooks, or links formed from bolts,
rods, etc., or other such attachments shall not be used.
Nonstandard end fittings designed by a qualified person
may be used. Where used, handles shall be welded to
the master link or hook prior to heat treating.
Hook characteristics shall meet the requirements of
ASME/ANSI B30.10.
Inspection Classification
(A) Initial Inspection. Prior to use, all new, altered,
modified, or repaired slings shall be inspected by a
designated person to insure compliance with the
applicable provisions of Sections 9–1.1 through 9–
1.5 of this Standard.
(B) Inspection procedure for chain slings in regular
service is divided into two general classifications
based upon the interval at which inspection should
be performed. The intervals in turn are dependent
upon the degree of exposure of the sling components to wear and deterioration. The two general
classifications are herein designated as frequent
and periodic with respective intervals between inspections as defined below.
(1) Frequent Inspection. Visual examinations by the
user or other designated personnel with records
not required.
(a) Normal service — monthly
(b) Severe service — daily to weekly
(c) Special or infrequent service — as recommended by a qualified person before and after
each occurrence.
(2) Periodic Inspection. Visual inspection by a designated person making a record of the inspection or of apparent conditions to provide basis
for a continuing evaluation.
(a) Normal service — yearly
(b) Severe service — monthly–quarterly
(c) Special or infrequent service — as recommended by a qualified person before the first
such occurrence and as directed by the qualified person for any subsequent occurrences.
Frequent Inspection
Slings shall be inspected for defects and damage at intervals as defined in para 9–1.6.1(b)(1) of Standards. In
addition, visual observations should be conducted during
regular service for any damage or evidence of malfunction that appears between regular inspections. Any deficiencies such as listed shall cause the
sling to be set aside for periodic inspection.
(A) Check Chain and attachments for wear, nicks,
cracks, breaks, gouges, stretch, bends, weld splatter, discoloration
from excessive temperature, and throat opening of
hooks.
(1) Chain links and attachments should hinge
freely with adjacent links.
(2) Latches on hook, if present, should hinge
freely and seat properly without evidence of
permanent distortion.
Periodic Inspection
Complete link by link inspections of the slings shall be
performed at intervals as defined in para. 9–1.6.1(b)(2)
of Standards.
Any deficiencies, such as listed, shall be examined and
determination made as to whether they constitute a hazard. These
inspections shall include the requirements of para. 9–
1.6.2 and, in addition, items such as the following:
(A) Each link and each attachment shall be examined
individually, taking care to expose inner link surfaces of the chain and chain attachments to inspect for those items defined in para. 9–1.6.2.
2
CHAIN USAGE (CONTINUED)
(1) Worn links should not exceed values given in
Table 2 of Standards or that which is specifically recommended by the manufacturer.
(2) Sharp transverse nicks and gouges should be
rounded out by grinding and the depth of the
gouge or rounded out portion should not exceed values given in Table 2 of Standards.
(3) Hooks should be inspected in accordance with
ASME/ANSI B30.10.
(4) If present, latches on hooks should seat properly, rotate freely, and show no permanent
distortion.
Proof Test
Prior to use, the welded components of all new slings
shall be proof tested by the component or sling manufacturer to twice the rated load.
All repaired or reconditioned slings that require heat
treating or welding shall be proof tested to twice the rated
load, with written records kept of such testing.
The proof load for multiple leg slings should be applied to
the individual legs and shall be twice the rated load of a
single leg sling. Mechanically assembled slings need not
be proof tested provided all welded components have
been proof tested.
Repairs
(A) Any hazardous condition disclosed by the inspection requirements of para. 9–1.6.1 shall be corrected before use of the chain or sling is resumed.
(B) Repairs shall be made only by the chain manufacturer or qualified personnel.
(C) When repairs are made, the following criteria shall
be followed:
(1) Alloy steel chain and coupling links used for
repair shall conform to the strength requirements and other requirements of the Standard. Cracked, broken, or bent links shall
not be repaired; they shall be replaced.
(2) When repaired, a sling shall be permanently
marked to identify the repairing
(3) Attachments which are used for repair shall
conform to the strength requirements and
other requirements of this Standard.
Cracked, broken, or bent attachments shall
not be repaired; they shall be replaced.
Operating Practices
a Slings having suitable characteristics for the
type of load, hitch, and environment shall be
selected in accordance with the requirements
of Section 9–1.4.
b The weight of load shall be within the rated load
of the sling.
c Slings shall not be shortened or lengthened by
knotting, twisting, or other methods not approved by the sling manufacturer.
d Slings that appear to be damaged shall not be
used unless inspected and accepted as usable
under Section 9–1.6.
e The sling shall be hitched or rigged in a manner
providing control of the load.
f Sharp corners in contact with the sling should
be padded with material of sufficient strength to
minimize damage to the sling.
g Portions of the human body should be kept
from between the sling and the load, from between the sling and the crane hook or hoist
hook.
h Personnel should stand clear of suspended
load.
i Personnel shall not ride the sling.
j Shock loading should be avoided.
k Slings should not be pulled from under a load
when the load is resting on the sling.
l Slings should be stored in an area where they
will not be subjected to mechanical damage,
corrosive action, moisture, extreme heat, or
kinking.
m Twisting and kinking the legs shall be avoided.
n The load applied to the hook should be centered in the base (bowl) of hooks to prevent
point loading on the hook, unless the hook is
designed for point loading.
o During lifting, with or without load, person shall
be alert for possible snagging.
p In a basket hitch, the load should be balanced
to prevent slippage.
q The sling’s legs should contain or support the
load so that the load remains under control.
r Multiple leg slings shall be selected when used
at the specific angles. Operation at other angles shall be limited to rated loads of the next
lower angle given in the table or calculated
trigonometrically (see para. 9– 2.2.1(d)) so as
to not introduce into the leg itself a load in direct tension greater than that permitted.
s Slings should be long enough so that the rated
load is adequate when the angle of the legs is
taken into consideration.
t Slings should not be dragged on the floor or
over an abrasive surface.
u When used in a choker hitch arrangement,
slings shall be selected to prevent load developed on any portion of the sling from exceeding the rated load of the sling components.
from An American National Standard
Safety Standard for Cableways,
Cranes, Derricks, Hoists, Hooks, Jacks, and Slings
ASME B30.9c-2000
Addenda to ASME B30.9–1990 Slings
The American Society of Mechanical Engineers
United Engineering Center, 345 East 47th Street
New York, N. Y. 10017
NOTE:
LiftPRO by NESCO, Inc. assumes no responsibility for the misuse or misapplication of any of its products.
Products are provided with the express understanding that the
purchaser and/or user are thoroughly familiar with the correct
application and proper use. Warnings and definitions are provided
as an aid to the user in understanding correct application and
proper use. These charts are not a substitute to proper training.
3
ORDERING SLINGS AND CHAIN STYLES
Ordering LiftPRO
Alloy Mechanical Chain Slings
1. Determine size of chain needed to lift the load
2. Determine number of legs as dictated by
weight or balance considerations
TYPE
SOO
SOS
SOG
SSS
SGG
SGS
3. Determine reach of sling, which is measured
from bearing point to bearing point
Chain Slings are Manufactured
with a 4:1 Design Factor
TYPE
DOS
DOG
DOUBLE TYPE SLINGS
TYPE
Double Chain with Master Link and Sling Hooks
TOS
TOG
Double Chain with Master Link and Sling Hooks
Chain Slings have 4:1 Design Factor
TYPE
SINGLE TYPE SLINGS
Single Chain with Master Link Each End
Single Chain with Master Link and Sling Hook
Single Chain with Master Link and Grab Hook
Single Chain with Sling Hook on Each End
Single Chain with Grab Hook on Each End
Single Chain with Grab Hook and Sling Hook
Chain Slings have 4:1 Design Factor
TRIPLE TYPE SLINGS
Triple Chain with Master Link and Sling Hooks
Triple Chain with Master Link and Sling Hooks
Chain Slings have 4:1 Design Factor
QUADRUPLE TYPE SLINGS
TYPE
SINGLE & DOUBLE TYPE SLINGS
QOS
Quadruple Chain
with Master Link and Sling Hooks
SOS-B
Adjustable Single Chain
with Master Link and Sling Hooks
QOG
Quadruple Chain
with Master Link and Sling Hooks
DOS-B
Adjustable Double Chain
with Master Link and Sling Hooks
Chain Slings have 4:1 Design Factor
Chain Slings have 4:1 Design Factor
4
GRADE 80 CHAIN WORKING LOAD LIMITS
SINGLE TYPE SLINGS
Grade 80
Chain
Size
(In)
9/32
3/8
1/2
5/8
3/4
7/8
1
Oblong Master Link (In)
WLL* in Lbs.
90
Nom.
Inside Inside Degree
Dia.
Width Length
Angle
1/2
2-1/2
5
3,500
3/4
2-3/4
5-1/2
7,100
1
3-1/2
7
12,000
1
3-1/2
7
18,100
1-1/4
4-3/8
8-3/4
28,300
1-1/2
5-1/4 10-1/2
34,200
1-3/4
6
12
47,700
* Working Load Limits
Chain Slings have 4:1 Design Factor
SINGLE
Single
Choker
Hitch
2,625
5,325
9,000
13,575
21,225
25,650
35,775
DOUBLE - 2 LEGS
Attachment, One End
Single Basket
60
45
30
Nom. Degree Degree Degree
Dia.
Angle
Angle
Angle
1/2
6,100
4,900
3,500
3/4
12,300 10,000
7,100
1
20,800 17,000 12,000
1-1/4
31,300 25,600 18,100
1-1/2
49,000 40,000 28,300
1-3/4
59,200 48,400 34,200
2
82,600 67,400 47,700
* Working Load Limits
Chain Slings have 4:1 Design Factor
Grade 80
Chain
Size
(In)
9/32
3/8
1/2
5/8
3/4
7/8
1
Grade 80
90
Chain Size
Degree
(In)
WLL*
9/32
3,500
3/8
7,100
1/2
12,000
5/8
18,100
3/4
28,300
7/8
34,200
1
47,700
* Working Load Limits
4:1 Design Factor
5
GRADE 80 CHAIN WORKING LOAD LIMITS
DOUBLE - 2 LEGS
Oblong Master Link (In)
Grade 80
Chain Size
(In)
9/32
3/8
1/2
5/8
3/4
7/8
1
60
45
30
Inside Inside Degree Degree Degree
Width Length Angle
Angle
Angle
2-1/2
5
6,100
4,900
3,500
2-3/4
5-1/2 12,300 10,000
7,100
3-1/2
7
20,800 17,000 12,000
4-3/8
8-3/4 31,300 25,600 18,100
5-1/4
10-1/2 49,000 40,000 28,300
6
12
59,200 48,400 34,200
7
14
82,600 67,400 47,700
* Working Load Limits
Chain Slings have 4:1 Design Factor
Nom.
Dia.
1/2
3/4
1
1-1/4
1-1/2
1-3/4
2
TRIPLE - 3 LEGS
Oblong Master Link (In)
Grade 80
Chain
Size
9/32
3/8
1/2
5/8
3/4
7/8
1
45
60
Inside Inside Degree Degree
Angle
Width Length Angle
2-3/4
5-1/2
9,100
7,400
3-1/2
7
18,400 15,100
4-3/8
8-3/4 31,200 25,500
5-1/4 10-1/2 47,000 38,400
6
12
73,500 60,000
7
14
88,900 72,500
8
16
123,900 101,200
* Working Load Limits
Chain Slings have 4:1 Design Factor
Nom.
Dia.
3/4
1
1-1/4
1-1/2
1-3/4
2
2-1/4
30
Degree
Angle
5,200
10,600
18,000
27,100
42,400
51,300
71,500
QUAD - 4 LEGS
Oblong Master Link (In)
Grade
80
Chain
9/32
3/8
1/2
5/8
3/4
7/8
1
6
60
45
30
Nom. Inside Inside
Degree Degree Degree
Dia. Width Length
Angle
Angle
Angle
3/4
2-3/4
5-1/2
9,100
7,400
5,200
1
3-1/2
7
18,400 15,100 10,600
1-1/4 4-3/8
8-3/4
31,200 25,500 18,000
1-1/2 5-1/4
10-1/2
47,000 38,400 27,100
1-3/4
6
12
73,500 60,000 42,400
2
7
14
88,900 72,500 51,300
2-1/4
8
16
123,900 101,100 71,500
* Working Load Limits
Chain Slings have 4:1 Design Factor
GRADE 80 CHAIN ATTACHMENTS
Eye Sling Hook
• Individually proof tested
• Painted orange
• Raised markings to assist proper application
• Replacement latch and pin kits available
Eye Sling Hook w ithout Latch Specifications
Chain size WLL*
(in.) (m m ) (lbs.)*
7/32 5.5 2,100
9/32 7 3,500
3/8 10 7,100
1/2 13 12,000
5/8 16 18,100
3/4 20 28,300
7/8 22 34,200
1
26 47,700
1-1/4 32 72,300
Product Product
Code
Code Latch
w Latchw /o Latch Kit
558544 458544 595461
558322 458722 595523
558325 458725 595525
558328 458728 595528
558329 458729 595529
558330 458730 595530
558332 595532 595532
558333 595533 595533
558335 458735 595535
B
1.62
2.06
2.63
3.06
3.50
3.88
4.31
5.31
D
3.31
3.50
4.33
5.50
6.34
7.83
8.59
9.59
11.28
E
1.44
1.50
1.88
2.25
2.63
3.00
3.38
4.00
4.66
G
4.30
5.25
6.64
8.16
9.66
11.38
12.72
14.23
17.00
Dim ensions (inches)
H
I
K
L
0.38 0.78 1.25 0.75
0.44 0.73 1.59 0.75
0.56 0.95 2.19 0.94
0.75 1.17 2.56 1.13
0.88 1.44 2.63 1.31
1.00 1.69 3.44 1.50
1.09 1.94 3.88 1.69
1.22 2.14 4.25 1.88
1.50 2.62 4.64 2.31
M
3.06
3.75
4.78
5.69
6.50
7.81
8.75
9.88
11.50
N
1.25
1.19
1.44
1.78
2.03
2.50
2.78
3.13
3.88
O
1.00
1.20
1.45
1.94
2.38
2.83
3.22
3.55
4.25
P
0.86
1.05
1.28
1.66
2.19
2.51
2.84
3.09
3.89
S
1.11
1.06
1.31
1.63
1.75
2.19
2.38
2.78
3.41
Wt.
(lbs.)
0.66
1.10
1.90
4.00
7.30
12.00
18.10
22.60
47.00
Clevlok Sling Hook
• Attaches quickly to chain
• Individually proof tested
• Painted orange
• Raised markings to assist proper application
• Replacement latch and pin kits available
Clevlok Sling Hook (Eye Style) w ithout Latch Specifications
Chain size
(in.) (m m )
9/32
7
3/8
10
1/2
13
5/8
16
3/4
20
WLL*
(lbs.)*
3,500
7,100
12,000
18,100
28,300
Product
Product
Code
Code
w ith Latch w /o Latch
658318
658338
658319
658339
658320
658340
658321
658341
658322
658342
Latch
Kit
595523
595525
595528
595529
595530
D
3.5
4.34
5.50
6.28
7.83
G
5.16
6.67
8.00
9.69
11.69
7
H
0.33
0.45
0.59
0.75
0.88
Dim ensions (inches)
I
L
M
0.73 0.36 3.44
0.95 0.51 4.47
1.17 0.63 5.27
1.44 0.75 6.08
1.69 0.91 7.34
O
1.20
1.45
1.94
2.38
2.83
P
1.05
1.28
1.66
2.19
2.56
R
1.06
1.31
1.56
1.75
2.19
Wt.
(lbs.)
1.20
2.30
4.33
8.10
12.70
GRADE 80 CHAIN ATTACHMENTS
Hammerlok Coupling
Ham m erlok Coupling Link Specifications
Chain size
(in.)
(m m )
7/32
5.5
9/32
7
3/8
10
1/2
13
5/8
16
3/4
20
7/8
22
1
26
1-1/4
32
WLL*
(lbs.)*
2,100
3,500
7,100
12,000
18,100
28,300
34,200
47,700
72,300
Product
Code
664021
664028
664038
664050
664062
664075
664089
664100
664125
Weight
A
0.25
0.31
0.48
0.66
0.78
0.94
1.05
1.25
1.53
B
1.41
1.94
2.41
3.40
4.06
4.78
5.25
6.00
6.81
C
.60
.86
1.04
1.48
1.78
2.11
2.28
2.62
2.96
D
0.44
0.55
0.81
1.18
1.43
1.74
1.89
2.36
2.70
E*
1.32
1.57
2.20
3.04
3.69
4.16
5.19
6.08
7.58
.12
.26
.59
1.42
2.35
3.67
5.98
9.47
16.61
Eye Foundry Hook
• Up to a 6" throat opening
• “I” beam body for grip when removing from load
• CM Hammerlok’s work well when attaching to chain
• Sizes to 1-1/4" with working load limits up to 72,300 lbs.
Foundry Hook
Chain size
(in.) (m m)
9/32
7
3/8
10
1/2
13
5/8
16
3/4
20
7/8
22
1
26
1-1/4
32
WLL* Product
(lbs.)* Code
3,500 474498
7,100 474499
12,000 474500
18,100 474501
28,300 474502
34,200 474503
47,700 474504
72,300 474505
B
1.56
2.00
2.50
3.00
3.50
4.00
4.50
5.13
D
4.75
5.75
6.75
7.81
9.13
10.14
11.13
12.84
E
2.50
3.00
3.50
4.00
4.50
5.00
5.50
6.00
G
6.45
7.88
9.38
10.97
12.81
14.23
15.84
18.03
Dimensions (inches)
H
I
K
L
0.47
1.00
1.56
0.63
0.63
1.27
1.88
0.75
0.75
1.50
2.22
1.00
0.88
1.81
2.63
1.25
1.00
2.20
3.00
1.50
1.13
2.25
3.38
1.75
1.25
2.59
3.75
2.13
1.38
3.17
4.25
2.38
8
M
4.75
5.75
6.88
8.06
9.25
10.38
11.56
12.88
N
2.50
3.00
3.50
4.00
4.50
5.00
5.50
6.00
O
1.23
1.50
1.75
2.03
2.56
2.78
3.03
3.81
R
0.25
0.31
0.38
0.44
0.50
0.56
0.62
0.75
Wt.
(lbs.)
2.4
4.5
7.1
11.6
20.0
26.0
36.8
58.4
GRADE 80 CHAIN ATTACHMENTS
Clevlok Grab Hook
• Designed without lugs for applications where lugs are not wanted
• CM’s clevlok design for easy assembly to chain
• Replacement pins available
• Painted orange
Clevlok Grab Hook
Chain size WLL* Product Load Retainer
(in.) (m m ) (lbs.)* Code
Pin
Pin
B
D
E
G
H
K
L
M
P
T
Wt.
.81
.6
9/32
7
3,500 559232 595780 602326 1.36 1.91 0.36 3.70 .33 1.04
.36 2.29 .76
3/8
10
7,100 559235 595782 495821 1.90 2.78 0.47 4.81 .45 1.49
.51 2.87 1.03 1.06 1.3
1/2
13 12,000 559238 595782 495822 2.31 3.62 0.59 6.35 .59 1.98
.63 3.78 1.51 1.38 2.5
5/8
16 18,100 559239 495783 659232 2.87 4.41 0.75 7.74 .75 2.39
.75 4.82 1.80 1.69 4.4
Clevlok Cradle Grab Hook
• Attaches quickly to chain
• CM’s unique cradle grab design
• Replacement pins available
• Painted orange
• Raised markings to assist proper application
Clevlok Cradle Grab Hook
Chain size WLL* Product
(in.) (m m ) (lbs.)*
Code
H
K
9/32
7
3,500
659222
1.31 1.78 .359 3.00 .33
B
D
E
G
.98
.36 1.63
3/8
10
7,100
659225
1.81 2.56 .469 4.08 .45
1.41
.51 2.11 1.06 1.75 1.18
1/2
13
12,000
659228
2.16 3.25 .594 5.27 .59
1.88
.63 2.88 1.28 2.13 2.70
5/8
16
18,100
659229
2.69 4.08 .750 6.53 .75
2.38 0.75 3.56 1.59 2.50 4.60
9
L
M
P
.72
T
Wt.
1.19 .44
GRADE 80 CHAIN ATTACHMENTS
Eye Cradle Grab Hook
• CM’s unique cradle grab design
• Painted orange
• Raised markings to assist proper application
Eye Cradle Grab Hook
Chain size
(in.) (m m )
7/32 5.5
9/32
7
3/8
10
1/2
13
5/8
16
3/4
20
7/8
22
1
26
WLL*
(lbs.)*
2,100
3,500
7,100
12,000
18,100
28,300
34,200
47,700
Product
Code
559318
559325
559337
559350
559362
559575
559387
559100
B
1.19
1.38
1.78
2.28
2.75
3.19
3.75
4.31
D
1.75
1.81
2.63
3.34
4.08
5.23
5.69
7.00
E
0.36
0.36
0.45
0.59
0.75
0.88
1.00
1.19
Dim ensions (inches)
G
H
I
K
2.69 0.38 1.19
0.96
3.44 0.38 1.19
0.99
4.67 0.50 1.75
1.48
5.86 0.63 1.88
1.98
7.13 0.75 2.25
2.63
8.99 0.88 2.88
3.50
9.63 1.00 3.00
3.75
12.44 1.22 3.88
4.31
L
0.63
0.63
0.78
1.03
1.25
1.44
1.75
1.88
M
1.63
2.36
3.11
3.94
4.78
6.25
6.50
8.09
P
0.70
0.70
1.06
1.30
1.59
1.88
2.12
3.12
Wt.
(lbs.)
0.35
0.4
1.06
2.26
4.36
8.82
10.40
20.90
Sorting Hook
• Designed for efficient handling of flat plates, large
cylindrical shapes and lifting loops
• 5:1 design factor
• Offered with or without handle
• Handle feature allow easy removal from loads
• When tip loading the working load drops 2 tons
(sticking the point into a pipe or tube, etc.
Sorting Hook
Product
Code
M129
M129H
WLL
Tip
Tons
2
2
WLL
Bottom
Tons
7.5
7.5
A
In.
3
3
B
In.
1.44
1.44
C
In.
0.78
0.78
D
In.
7.34
7.34
Dim ensions (inches)
E
F
G
H
In.
In.
In.
In.
3.75 1.28
1.25
4.13
3.75 1.28
1.25
4.13
10
I
In.
10.09
10.09
J
In.
n/a
2.13
K
In.
n/a
4.63
L
In.
n/a
9.56
M
In.
7.38
7.38
Wt.
lb.
6.8
7
GRADE 80 CHAIN ATTACHMENTS
Clevlok Lodelok
• Will fit grade 80 or grade 100
• Open design permits multi-hardware use
• Interlocking tip gives added protection
• New “I” beam no catch point design
• Designed to meet ASTM A952 & EN1677
Clevlok Lodelok
Chain size
WLL*
(in.) (m m ) (lbs.)*
Product
Latch
Code
Kit
D
G
H
J
K
L
F
P
M
Wt.
9/32
7
4,300
616005
656005
3.89 6.37 0.35 1.00 1.19 0.36
1.56
1.00
4.68
2.62
3/8
10
8,800
616010
656010
5.03 8.20 0.47 1.16 1.25 0.51
2.25
1.25
6.11
4.93
1/2
13
15,000
616015
656015
6.68 10.07 0.59 1.50 1.63 0.63
2.81
1.75
7.25
9.32
5/8
16
22,600
616020
656020
8.04 11.62 0.71 1.74 1.88 0.75
3.19
2.00
8.36
14.70
Eye Lodelok
• Open design permits multi hardware use
• Interlocking tip gives added protection
• Designed for efficient handling of flat plates, large cylindrical
shapes and lifting loops
• New “I” beam no catch point design
• Designed to meet ASTM A952 & EN1677
• For welded 7/32” chain sling use 9/32” eye hook
Eye Lodelok
Chain size
WLL*
(in.) (m m ) (lbs.)*
Product
Code
Latch
Kit
C
G
H
K
Wt.
9/32
7
4,300
626005
656005
2.00
1.31 5.43
B
M
1.00 3.89 1.563
P
D
Fm in
1.47
0.63
1.19
2.64
3/8
10
8,800
626010
656010
2.50
1.78 7.41
1.25 5.03 2.250
2.00
0.75
1.25
4.86
1/2
13
15,000
626015
656015
3.44
2.38 9.38
1.75 6.68 2.813
2.59
1.00
1.63
10.46
5/8
16
22,600
626020
656020
3.94
2.62 10.71 2.00 8.04 3.125
2.92
1.25
1.88
16.52
11
GRADE 80 CHAIN ATTACHMENTS
Swivel Lodelok
• Permits positioning of the load before lift
• Open design permits multi hardware use
• Interlocking tip gives added protection
• New “I” beam no catch point design
• Designed to meet ASTM A952 & EN1677
• For welded 7/32” chain sling use 9/32” eye hook
Sw ivel Lodelok
Chain size
WLL*
(in.)
(m m )
(lbs.)*
Code
Kit
A
B
M
K
H
Wt.
9/32
7
4,300
676005
656005
1.50
1.33
6.79
1.00 3.89 1.563
1.19
0.50
2.61
3/8
10
8,800
676010
656010
1.75
1.63
8.77
1.25 5.03 2.250
1.25
0.63
5.09
1/2
13
15,000
676015
656015
2.00
1.76
10.54 1.75 6.68 2.813
1.63
0.75
11.03
5/8
16
22,600
676020
656020
2.75
2.38
12.80 2.00 8.04 3.125
1.88
1.00
18.09
Product
Latch
P
D
F m in.
Hammer Lodelok
• Easily attaches chain to positive locking Lodelok hook
• Factory replacement pin
• Interlocking tip gives added protection
• For welded 7/32" chain sling use 9/32" eye hook
Ham m er Lodelok——100% Proof Tested
Chain size
WLL*
Product
(in.)
(m m )
(lbs.)*
Code
Latch
Kit
G
B
M
P
9/32
7
4,300
666005
656005
6.84
0.54
0.71
5.44
3.89 1.563 0.500 1.19
2.06
3/8
10
8,800
666010
656010
9.11
0.91
1.16
7.33
5.03 2.250 0.709 1.25
4.80
1/2
13
15,000
666015
656015
11.88
1.10
1.43
9.38
6.68 2.813 0.859 1.63 10.00
5/8
16
22,600
666020
656020
13.55
1.32
2.09
10.68
8.04 3.130 0.770 1.88 15.30
12
D
Fm in
H
K
Wt.
GRADE 80 CHAIN ATTACHMENTS
Hook Latch Kit, Plate Hook
Plate Hook:
• Made from alloy material
• Designed to handle plate steel
• Available as components or attached to a certified sling
Chain Size Product
ins.
Code
9/32
595523
3/8
595525
1/2
595528
5/8
595529
3/4
595530
7/8
595532
Chain Size
ins.
mm
9/32
7
3/8
10
1/2
13
5/8
16
3/4
20
7/8
22
Omegalok Connector
• Attaches chain to master links and other components with
engineered flats
• Raised markings to assist proper application
• Replacement pin kits available
• Clevlok heads for quick and easy attachment to chain
Clevlok Sling Hook (Eye Style) w ithout Latch Specifications
Chain size
(in.) (m m )
9/32
7
3/8
10
1/2
13
5/8
16
WLL*
(lbs.)*
3,500
7,100
12,000
18,100
Product
Code
244128
244138
244150
244162
B
1.36
1.90
2.31
2.87
D
2.30
2.82
3.52
4.46
Dim ensions (inches)
E
G
H
L
0.98 2.81
0.33 0.36
1.25 3.57
0.45 0.51
1.56 4.44
0.59 0.63
2.00 5.45
0.75 0.78
13
M
1.45
1.77
2.26
2.72
T
0.43
0.57
0.70
0.88
Wt.
(lbs.)
0.40
1.02
1.92
3.20
WLL
(lbs.)
3,600
7,050
11,400
17,800
25,600
34,900
Product
Code
462528
462537
462550
462562
462575
462587
W
2.500
2.750
3.500
5.000
5.750
6.000
GRADE 80 CHAIN ATTACHMENTS
Foundry Sorting Hook
Chain
Size
0.28
0.28
0.28
0.38
0.38
0.38
0.50
0.50
WLL*
(lbs.)*
500
800
1,300
1,600
2,500
3,500
4,500
6,000
Chain
Size
0.28
0.28
0.28
0.38
0.38
0.38
0.50
WLL*
(lbs.)*
450
900
1,400
2,000
3,000
4,000
5,500
WLL*
(lbs.)*
250
350
650
850
1,200
1,500
2,000
2,250
2,750
3,000
3,500
4,000
5,000
Product
Code A
JAA031
JAA038
JAA050
JAA063
JAA075
JAA088
JAA100
JAA113
JAA125
JAA138
JAA150
JAA175
JAA200
Foundry Sorting Hook
Product Material
Inside Inside I.D.
Bowl
Tip
Code Diameter A Reach B
Eye C Opening D Length E
FSA050
0.50
6.00
0.75
2.50
0.75
FSA063
0.63
8.50
0.75
3.50
1.50
FSA075
0.75
8.50
0.75
3.50
1.50
FSA081
0.81
8.50
0.88
3.50
1.50
FSA100
1.00
8.50
1.00
4.00
1.75
FSA113
1.13
8.50
1.00
4.00
2.00
FSA125
1.25
8.50
1.25
4.00
2.00
FSA150
1.50
8.50
1.25
5.00
1.50
Foundry Sorting Hook - Short Version
Product Material
Inside Inside I.D.
Bowl
Tip
Code Diameter A Reach B
Eye C Opening D Length E
FSA050S
0.50
6.00
0.75
3.00
1.50
0.63
6.00
0.75
3.00
1.50
FSA063S
FSA075S
0.75
6.00
0.75
3.00
1.50
FSA088S
0.88
6.00
0.88
3.00
1.50
FSA100S
1.00
6.00
1.00
3.00
1.50
1.13
6.00
1.00
3.00
1.50
FSA113S
FSA125S
1.25
6.00
1.25
3.00
1.50
Product
Code B
JBA031
JBA038
JBA050
JBA063
JBA075
JBA088
JBA100
JBA113
JBA125
JBA138
JBA150
JBA175
JBA200
Standard Alloy J - Hooks
Product Material Inside Inside I.D. Bow l
Code C
Dia. A
Reach B
Eye C
Open D
JCA031
0.31
5.00
0.75
1.25
JCA038
0.38
6.00
0.75
1.50
JCA050
0.50
8.00
0.75
2.00
JCA063
0.63
9.00
1.00
2.50
JCA075
0.75
10.00
1.00
3.00
JCA088
0.88
12.00
1.00
3.50
JCA100
1.00
14.00
1.25
4.00
JCA113
1.13
15.00
1.25
4.50
JCA125
1.25
16.00
1.50
5.00
JCA138
1.38
17.00
1.50
5.50
JCA150
1.50
18.00
2.00
6.00
JCA175
1.75
20.00
2.50
7.00
JCA200
2.00
24.00
3.00
8.00
14
Tip
Lgth. E
0.25
0.38
0.50
0.63
0.75
0.88
1.00
1.12
1.25
1.38
1.50
1.75
2.00
GRADE 80 CHAIN ATTACHMENTS
Grade 100 Oblong Master Rings
• Used for mechanical and welded sling assemblies
• 100% proof tested
• Custom sizes available upon request
Oblong Master Ring Specifications, (With Flat) Specifications
Size
(in.)
3/8
1/2
5/8
3/4
7/8
1
1-1/4
1-3/8
1-1/2
1-5/8
1-3/4
2
2-1/4
2-1/2
2-3/4
3-1/4
Product Code For Chain Size (in.)
(m m )
1 Leg
2 Leg
589614
589615
1/4
589616
1/4
589617
3/8
3/8
589618
589619
1/2, 5/8
1/2
589620
3/4
5/8
589621
589622
7/8
3/4
589623
589624
1
7/8
589625
1-1/4
1
589626
1-1/4
589627
589628
589629
WLL
(lbs.)
3,300
7,000
11,400
12,300
17,200
29,900
35,200
45,300
68,000
70,400
84,900
102,600
143,100
160,000
220,200
275,300
Dim ensions (ins.)
L
B
D
3.9
2.4
.43
4.7
2.8
.55
5.5
3.2
.67
5.9
3.5
.75
6.3
3.7
.87
7.5
4.3
.99
7.9
4.7
1.2
9.5
5.5
1.3
9.9
5.9
1.5
9.9
5.9
1.6
11.8
7.1
1.8
11.8
7.9
2.0
11.8
7.9
2.2
13.8
7.9
2.4
15.8
9.9
2.8
15.8
9.9
3.2
Weight
.44
.88
1.8
2.2
3.3
5.1
7.7
11.7
15.4
17.6
26.5
33.1
46.3
57.3
94.8
125.6
Oblong Master Ring w ith Sub-Assem bly Specifications
Size
(in.)
3/4
7/8
1
1-1/4
1-5/8
2
2-1/4
2-1/2
2-3/4
3-1/4
Product
Code WLL (lbs.) WLL (lbs.)
4:1 Design 5:1 Design
589630
13,750
11,000
589631
22,000
17,600
589632
26,625
21,300
589633
44,000
35,200
589634
71,500
57,200
589635
96,250
77,000
589636
137,625
110,100
589637
206,375
165,100
589638
275,250
220,200
589639
344,125
275,300
L1
10.2
11.8
13.4
14.2
16.9
19.7
22.0
24.0
26.8
26.8
L
5.9
6.3
7.5
7.9
9.9
11.8
11.8
13.8
15.8
15.8
Dim ensions
B
D
3.5
.75
3.7
.87
4.3
.98
4.7
1.2
5.9
1.6
7.9
2.0
7.9
2.2
7.9
2.4
9.9
2.8
9.9
3.1
15
(ins.)
1
4.3
5.5
5.9
6.3
7.1
7.9
10.2
10.2
11.0
11.0
Weight
b
2.4
3.2
3.5
3.7
4.1
4.3
5.5
5.5
6.3
6.3
d
.55
.67
.75
.87
1.1
1.3
1.5
1.8
2.0
2.2
4.0
6.8
7.0
14.3
33.1
50.7
72.7
101.4
156.5
200.6
GRADE 80 HOOKS
Safety Hooks
BK Safety Hook (Eye Type)
• Equipped with stainless steel springs
• Heat number identification for traceability
• Latch closes automatically under load
• Hook will not open under load
BK Safety Hook (Eye Type)
Chain size
(in.)
(mm)
7/32
6
9/32
7
5/16
8
3/8
10
1/2
13
5/8
16
3/4
20
7/8
22
1
26
WLL*
(lbs.)*
2,100
3,500
4,500
7,100
12,000
18,100
28,300
34,200
47,700
Product
code
511100
511110
511110
511120
511130
511140
511141
511142
511149
Model
Number
BK-5/6-8
BK-7/8-8
BK-7/8-8
BK-10-8
BK-13-8
BK-16-8
BK-18/20-8
BK-22-8
BK-26-8
L
4.30
5.40
5.40
6.60
8.20
10.00
11.40
12.60
13.60
B
1.10
1.40
1.40
1.70
2.10
2.50
2.70
3.10
3.90
Dimensions (inches)
E
F
0.87
0.39
0.99
0.43
0.99
0.43
1.30
0.51
1.60
0.63
2.00
0.79
2.40
0.87
2.80
0.95
3.10
1.00
G
0.55
0.67
0.67
0.98
1.10
1.50
1.70
1.90
2.00
H
0.750
0.910
0.910
1.100
1.500
1.900
2.200
2.400
2.700
Wt. Ea.
(lbs.)
0.97
1.70
1.70
3.30
6.20
12.30
17.40
24.70
32.00
G
0.55
0.67
0.67
0.83
1.10
1.20
1.40
1.60
H
0.670
0.790
0.790
0.970
1.200
1.500
1.900
2.200
Wt. Ea.
(lbs.)
0.88
1.40
1.40
2.60
4.40
9.00
16.50
22.00
OBK Safety Hook with Grip Latch (Eye Type)
• Equipped with stainless steel springs
• Heat number identification for traceability
• Grip latch locks into point of hooks
• Latch is protected and will act as a gauge to signal unsafe
bent hook or latch
OBK Safety Hook with Grip Latch (Eye Type)
Chain size
(in.)
(mm)
7/32
6
9/32
7
5/16
8
3/8
10
1/2
13
5/8
16
3/4
20
7/8
22
WLL*
(lbs.)*
2,100
3,500
4,500
7,100
12,000
18,100
28,300
34,200
Product
code
511004
511010
511010
511020
511030
511040
511045
511006
Model
Number
OBK-5/6-8
OBK-7/8-8
OBK-7/8-8
OBK-10-8
OBK-13-8
OBK-16-8
OBK-18/20-8
OBK-22-8
L
4.10
5.10
5.10
6.40
7.70
9.30
11.50
13.20
16
B
1.00
1.30
1.30
1.70
2.00
2.40
2.80
3.40
Dimensions (inches)
E
F
0.87
0.35
0.99
0.39
0.99
0.39
1.30
0.49
1.60
0.59
2.00
0.75
2.40
1.10
2.80
0.95
GRADE 80 SAFETY HOOKS
Safety Hooks
BKL Safety Hook with Bronze Bushings (Swivel Eye Type)
• Equipped with stainless steel springs
• Heat number identification for traceability
• Latch closes automatically under load
• Hook will not open under load
• Release trigger will only operate when hook is unloaded
• Bushing allows hook to swivel before load is applied
Chain size
(in.)
(mm)
7/32
6
9/32
7
5/16
8
3/8
10
1/2
13
5/8
16
3/4
20
WLL*
(lbs.)*
2,100
3,500
4,500
7,100
12,000
18,100
28,300
BKL Safety Hook with Bronze Bushings (Swivel Eye Type)
Dimensions (inches)
Product
Model
code
Number
L
B
E
F
511250
BKL-5/6-8
5.90
1.10
0.91
0.43
511260
BKL-7/8-8
7.20
1.40
1.10
0.47
511260
BKL-7/8-8
7.20
1.40
1.10
0.47
511270
BKL-10-8
8.60
1.70
1.50
0.59
511280
BKL-13-8
10.90
2.10
1.70
0.75
511290
BKL-16-8
13.20
2.50
2.30
0.87
589325 BKL-18/20-8 14.50
2.70
1.70
1.00
G
0.55
0.67
0.67
0.99
1.10
1.50
2.90
H
0.750
0.910
0.910
1.100
1.500
1.900
1.000
Wt. Ea.
(lbs.)
1.50
2.40
2.40
4.20
8.40
15.60
23.80
BKLK Safety Hook with Ball Bearings (Swivel Eye Type)
• Equipped with stainless steel springs
• Heat number identification for traceability
• Latch closes automatically under load
• Hook will not open under load
• Release trigger will only operate when hook is unloaded
• Ball bearing allows hook to swivel before load is applied
BKLK Safety Hook with Ball Bearings (Swivel Eye Type)
Chain size
(in.)
(mm)
7/32
6
9/32
7
5/16
8
3/8
10
1/2
13
5/8
16
3/4
20
WLL*
(lbs.)*
2,100
3,500
4,500
7,100
12,000
18,100
28,300
Product
code
511323
511324
511324
511325
511326
511327
589326
Model
Number
L
BKLK-5/6-8
5.80
BKLK-7/8-8
7.20
BKLK-7/8-8
7.20
BKLK-10-8
8.50
BKLK-13-8
10.90
BKLK-16-8
13.20
BKLK-18/20-8 14.50
17
B
1.10
1.40
1.40
1.70
2.10
2.50
2.70
Dimensions (inches)
C
E
F
0.87
1.30
0.43
1.10
1.40
0.47
1.10
1.40
0.47
1.30
1.60
0.59
1.60
1.90
0.75
2.00
2.40
0.87
1.70
2.30
2.20
G
0.55
0.67
0.67
0.99
1.10
1.50
2.90
H
0.750
0.910
0.910
1.100
1.500
1.900
1.000
Wt. Ea.
(lbs.)
1.50
2.40
2.40
4.20
8.40
15.90
23.80
GRADE 80 CHAIN EUROPEAN ATTACHMENTS
18
GRADE 80 CHAIN EUROPEAN ATTACHMENTS
Grade 80 Chain Approved for Overhead Lifting
19
GRADE 80 CHAIN EUROPEAN ATTACHMENTS
20
GRADE 80 CHAIN EUROPEAN ATTACHMENTS
21
GRADE 80 CHAIN EUROPEAN ATTACHMENTS
22
GRADE
GRADE 80
80 CHAIN
CHAIN EUROPEAN
EUROPEAN ATTACHMENTS
ATTACHMENTS
23
GRADE 100 CHAIN WORKING LOAD LIMITS
SINGLE TYPE SLINGS
Grade 100
Chain
Size
(In)
9/32
3/8
1/2
5/8
3/4
Oblong Master Link (In)
Nom.
Dia.
1/2
3/4
1
1
1-1/4
SINGLE
WLL* in Lbs.
Single
90
Inside Inside
Choker
Degree
Width Length
Hitch
Angle
2-1/2
5
4,300
2,625
2-3/4
5-1/2
8,800
5,325
3-1/2
7
15,000
9,000
3-1/2
7
22,600
13,575
4-3/8
8-3/4
35,300
21,225
* Working Load Limits
DOUBLE - 2 LEGS
Attachment, One End
90
Grade 100
Degree
Chain Size
WLL*
(In)
9/32
4,300
3/8
8,800
1/2
15,000
5/8
22,600
3/4
35,300
* Working Load Limits
4:1 Design Factor
Grade 100
Chain
Size
(In)
9/32
3/8
1/2
5/8
3/4
Single Basket
60
45
30
Nom. Degree Degree Degree
Dia.
Angle
Angle
Angle
1/2
7,400
6,100
4,300
3/4
15,200 12,400
8,800
1
26,000 21,200 15,000
1-1/4
39,100 32,000 22,600
1-1/2
61,100 49,900 35,300
* Working Load Limits
Chain Slings have 4:1 Design Factor
24
GRADE 100 CHAIN WORKING LOAD LIMITS
DOUBLE - 2 LEGS
Oblong Master Link (In)
Grade 100
45
60
Chain Size Nom. Inside Inside Degree Degree
(In)
Angle
Dia. Width Length Angle
9/32
1/2
2-1/2
5
7,400
6,100
3/8
3/4
2-3/4
5-1/2
15,200 12,400
1/2
1
3-1/2
7
26,000 21,200
5/8
1-1/4 4-3/8
8-3/4
39,100 32,000
3/4
1-1/2 5-1/4
10-1/2 61,100 49,900
* Working Load Limits
Chain Slings have 4:1 Design Factor
30
Degree
Angle
4,300
8,800
15,000
22,600
35,300
TRIPLE - 3 LEGS
Oblong Master Link (In)
Grade
100
Chain
9/32
3/8
1/2
5/8
3/4
60
45
Inside Inside Degre Degree
Width Length
e
Angle
2-3/4 5-1/2 11,200 9,100
3-1/2
7
22,900 18,700
4-3/8 8-3/4 39,000 31,800
5-1/4 10-1/2 58,700 47,900
6
12
91,700 74,900
* Working Load Limits
Chain Slings have 4:1 Design Factor
Nom.
Dia.
3/4
1
1-1/4
1-1/2
1-3/4
30
Degree
Angle
6,400
13,200
22,500
33,900
53,000
QUAD - 4 LEGS
Oblong Master Link (In)
Grade 100
Chain Size
(In)
9/32
3/8
1/2
5/8
3/4
25
60
45
Inside Inside Degree Degree
Width Length Angle
Angle
2-3/4
5-1/2
11,200 9,100
3-1/2
7
22,900 18,700
4-3/8
8-3/4
39,000 31,800
5-1/4
10-1/2 58,700 47,900
6
12
91,700 74,900
* Working Load Limits
Chain Slings have 4:1 Design Factor
Nom.
Dia.
3/4
1
1-1/4
1-1/2
1-3/4
30
Degree
Angle
6,400
13,200
22,500
33,900
53,000
GRADE 100 CHAIN ATTACHMENTS
Grade 100 Oblong Master Rings
• Used for mechanical and welded sling assemblies
• 100% proof tested
• Custom sizes available upon request
Oblong Master Ring Specifications, (With Flat) Specifications
Size
(in.)
3/8
1/2
5/8
3/4
7/8
1
1-1/4
1-3/8
1-1/2
1-5/8
1-3/4
2
2-1/4
2-1/2
2-3/4
3-1/4
Product Code For Chain Size (in.)
(m m )
1 Leg
2 Leg
589614
589615
1/4
589616
1/4
589617
3/8
3/8
589618
589619
1/2, 5/8
1/2
589620
3/4
5/8
589621
589622
7/8
3/4
589623
589624
1
7/8
589625
1-1/4
1
589626
1-1/4
589627
589628
589629
WLL
(lbs.)
3,300
7,000
11,400
12,300
17,200
29,900
35,200
45,300
68,000
70,400
84,900
102,600
143,100
160,000
220,200
275,300
Weight
Dim ensions (ins.)
L
B
D
3.9
2.4
.43
4.7
2.8
.55
5.5
3.2
.67
5.9
3.5
.75
6.3
3.7
.87
7.5
4.3
.99
7.9
4.7
1.2
9.5
5.5
1.3
9.9
5.9
1.5
9.9
5.9
1.6
11.8
7.1
1.8
11.8
7.9
2.0
11.8
7.9
2.2
13.8
7.9
2.4
15.8
9.9
2.8
15.8
9.9
3.2
.44
.88
1.8
2.2
3.3
5.1
7.7
11.7
15.4
17.6
26.5
33.1
46.3
57.3
94.8
125.6
Oblong Master Ring w ith Sub-Assem bly Specifications
Size
(in.)
3/4
7/8
1
1-1/4
1-5/8
2
2-1/4
2-1/2
2-3/4
3-1/4
Product
Code
589630
589631
589632
589633
589634
589635
589636
589637
589638
589639
WLL
(lbs.)
4:1
13,750
22,000
26,625
44,000
71,500
96,250
137,625
206,375
275,250
344,125
WLL (lbs.)
5:1 Design
11,000
17,600
21,300
35,200
57,200
77,000
110,100
165,100
220,200
275,300
L1
10.2
11.8
13.4
14.2
16.9
19.7
22.0
24.0
26.8
26.8
L
5.9
6.3
7.5
7.9
9.9
11.8
11.8
13.8
15.8
15.8
Dim ensions
B
D
3.5
.75
3.7
.87
4.3
.98
4.7
1.2
5.9
1.6
7.9
2.0
7.9
2.2
7.9
2.4
9.9
2.8
9.9
3.1
26
(ins.)
1
4.3
5.5
5.9
6.3
7.1
7.9
10.2
10.2
11.0
11.0
Weight
b
2.4
3.2
3.5
3.7
4.1
4.3
5.5
5.5
6.3
6.3
d
.55
.67
.75
.87
1.1
1.3
1.5
1.8
2.0
2.2
4.0
6.8
7.0
14.3
33.1
50.7
72.7
101.4
156.5
200.6
GRADE 100 CHAIN ATTACHMENTS
Hammerlok Coupling Links
• Proven design
• Forged from Alloy Steel
• 100% proof tested
• Designed to meet ASTM A952 & EN1677
HA1000 Ham m erlok Coupling Link Specifications
Stud
Assy
Product
Load Pin
Chain size
WLL*
Product
(in.)
(m m )
(lbs.)*
Code
A
B
C
D
E Min.
F
code
code
9/32
7
4,300
667028
0.365
0.435
1.98
0.71
0.541
1.69
598028
596028
3/8
10
8,800
667038
0.502
0.591
3.00
1.16
0.910
2.50
598038
596038
.84
1/2
13
15,000
667050
0.678
0.780
3.80
1.43
1.097
3.19
598050
596050
1.87
5/8
16
22,600
667062
0.804
0.905
4.54
1.74
1.317
3.88
598062
596062
3.13
3/4
20
35,300
667075
0.973
1.071
5.36
2.09
1.516
4.69
598075
596075
5/75
Product Weight
.28
Eye Foundry Hook
• Proven design
• Forged from Alloy Steel
• Large open throat makes attachment easy
• 100% proof tested
• Designed to meet ASTM A952 & EN1677
• For welded 7/32” chain sling use 9/32” eye hook
Foundry Hook
Chain size
(in.) (mm)
9/32
7
3/8
10
1/2
13
5/8
16
3/4
20
Working
LL*
(lbs.)*
4,300
8,800
15,000
22,600
35,300
Product
code
474798
474799
474800
474801
474802
B
1.56
2.00
2.50
3.00
3.50
D
4.75
5.75
6.75
7.81
9.13
E
2.50
3.00
3.50
4.00
4.50
G
6.45
7.88
9.38
10.97
12.81
Dimensions (inches)
H
I
K
L
0.47 1.00 1.56 0.63
0.63 1.27 1.88 0.75
0.75 1.50 2.22 1.00
0.88 1.81 2.63 1.25
1.00 2.20 3.00 1.50
27
M
4.75
5.75
6.88
8.06
9.25
N
2.50
3.00
3.50
4.00
4.50
O
1.23
1.50
1.75
2.03
2.56
R
0.25
0.31
0.38
0.44
0.50
Wt.
each
(lbs.)
2.4
4.5
7.1
11.6
20.0
GRADE 100 CHAIN ATTACHMENTS
Clevlok Sling Hook
• New streamlined design
• Forged from Alloy Steel
• Improved cast steel latch
• 100% proof tested
• Designed to meet ASTM A952 & EN1677
Clevlok Sling Hook*
Chain size
(in.) (mm)
9/32
7
3/8
10
1/2
13
5/8
16
WLL*
(lbs.)*
4,300
8,800
15,000
22,600
w Latch w/o Latch
Product Product
Code
Code
658718 658738
658719 658739
658720 658740
658721 658741
Latch
Kit
658718
658719
658720
658721
D
3.53
4.34
5.12
5.98
G
5.22
6.56
7.72
8.96
Dimensions (inches)
H
J
K
L
0.35 1.00 0.75 0.36
0.47 1.16 0.95 0.51
0.59 1.50 1.10 0.63
0.71 1.74 1.27 0.75
M
1.09
1.25
1.69
1.88
P
0.94
1.21
1.35
1.56
R
3.56
4.46
5.24
6.07
Wt.
each
(lbs.)
1.40
2.57
4.08
6.37
* A vailab le f r o m st o ck wit h/ wit ho ut lat ch. R ep lacement lat ch kit s ar e also availab le. U ser must d et er mine if lat ch is r eq uir ed o n ho o k.
Eye Sling Hook
• New streamlined design
• Forged from Alloy Steel
• 100% proof tested
• Designed to meet ASTM A952 & EN1677
• For welded 7/32" chain use 9/32" eye hook
Eye Sling Hook*
Chain size
(in.) (mm)
9/32 7
3/8
10
1/2
13
5/8
16
3/4
20
WLL*
(lbs.)*
4,300
8,800
15,000
22,600
35,300
w Latch
Product
code
558622
558625
558628
558729
558730
w/o Lth.
Product
code
458622
458625
458628
458729
458730
Latch
Kit
595523
595525
595528
595529
595530
B
1.6
2.1
2.6
3.1
3.50
D
3.50
4.33
5.50
6.34
7.83
E
1.5
1.9
2.3
2.6
3.00
G
5.25
6.64
8.16
9.66
11.38
H
0.44
0.56
0.75
0.88
1.00
I
0.73
0.95
1.17
1.44
1.69
K
1.59
2.19
2.56
2.63
3.44
L
0.75
0.94
1.13
1.31
1.50
M
3.75
4.78
5.69
6.50
7.81
N
1.19
1.44
1.78
2.03
2.50
O
1.20
1.45
1.94
2.38
2.83
* A vailab le f r o m st o ck wit h/ wi t ho ut lat ch. R ep lacement l at ch kit s ar e also avai lab le. U ser must d et er mine if l at ch i s r eq uir ed o n ho o k.
28
P
1.05
1.28
1.66
2.19
2.51
S
1.06
1.31
1.63
1.75
2.19
GRADE 100 CHAIN ATTACHMENTS
Clevlok Cradle Grab Hook
• New streamlined design
• Forged from Alloy Steel
• 100% proof tested
• Designed to meet ASTM A952 & EN1677
Clevlok Cradle Grab Hook
Chain size
(in.)
(mm)
9/32
7
3/8
10
1/2
13
5/8
16
WLL*
(lbs.)*
4,300
8,800
15,000
22,600
Product
code
659722
659725
659728
659729
D
2.18
2.72
3.32
4.18
G
3.38
4.33
5.27
6.54
H
0.38
0.47
0.65
0.79
Dimensions (inches)
J
K
L
0.80
0.95
0.36
1.16
1.27
0.51
1.24
1.54
0.63
1.53
1.92
0.75
M
0.38
0.47
0.65
0.79
P
0.82
1.02
1.18
1.41
R
1.86
2.47
3.05
3.75
Wt.
each
(lbs.)
0.63
1.3
2.1
4.2
P
1.76
1.04
1.51
1.80
1.88
Wt.
each
(lbs.)
0.55
1.39
3.05
4.36
9.00
Eye Cradle Grab Hook
• Proven design
• Forged from Alloy Steel
• Large open throat makes attachment easy
• 100% proof tested
• Designed to meet ASTM A952 & EN1677
• For welded 7/32” chain sling use 9/32” eye hook
Eye Cradle Grab Hook
Chain size
(in.)
(mm)
9/32
7
3/8
10
1/2
13
5/8
16
3/4
20
WLL*
(lbs.)*
4,300
8,800
15,000
22,600
35,300
Product
code
559725
559737
559750
559762
559775
B
1.38
1.78
2.28
2.75
3.19
D
1.91
2.78
3.63
4.41
5.23
E
0.36
0.47
0.59
0.75
0.88
Dimensions (inches)
G
H
I
K
3.70
0.38
1.06
1.04
4.81
0.50
1.38
1.49
6.19
0.63
1.81
1.98
7.62
0.75
2.13
2.39
8.99
0.88
2.88
3.50
29
L
0.63
0.78
1.03
1.25
1.44
M
12.57
13.28
14.22
15.06
6.25
GRADE 100 CHAIN ATTACHMENTS
Clevlok Lodelok Hook
• Will fit grade 80 or grade 100
• Open design permits multi hardware use
(Chain, Nylon & Wire Rope)
• Interlocking tip gives added protection
• Forged from Alloy Steel
• New “I” beam no catch point design
• 100% proof tested
• Designed to meet ASTM A952 & EN1677
Clevlok Lodelok Hook
Chain size
(in.)
(mm)
9/32
7
3/8
10
1/2
13
5/8
16
WLL*
(lbs.)*
4,300
8,800
15,000
22,600
Product
code
616005
616010
616015
616020
D
3.89
5.03
6.68
8.04
G
6.37
8.20
10.07
11.62
Dimensions (inches)
J
K
L
1.00
1.19
0.36
1.16
1.25
0.51
1.50
1.63
0.63
1.74
1.88
0.75
H
0.35
0.47
0.59
0.71
M
1.56
2.25
2.81
3.19
P
1.00
1.25
1.75
2.00
R
4.68
6.11
7.25
8.36
Wt.
each
(lbs.)
2.62
4.93
9.32
14.70
Eye Lodelok Hook
• Open design permits multi hardware use
(Chain, Nylon & Wire Rope)
• Interlocking tip gives added protection
• Forged from Alloy Steel
• New “I” beam no catch point design
• 100% proof tested
• Designed to meet ASTM A952 & EN1677
• For welded 7/32" chain sling use 9/32" eye hook
Eye Lodelok Hook
Chain size
(in.)
(mm)
9/32
7
3/8
10
1/2
13
5/8
16
WLL*
(lbs.)*
4,300
8,800
15,000
22,600
Product
code
626005
626010
626015
626020
A
2.00
2.50
3.44
3.94
B
1.31
1.78
2.38
2.62
C
5.43
7.41
9.38
10.71
30
Dimensions (inches)
D
E
F min
1.00
3.89 1.563
1.25
5.03 2.250
1.75
6.68 2.813
2.00
8.04 3.125
G
1.47
2.00
2.59
2.92
H
0.63
0.75
1.00
1.25
J
1.19
1.25
1.63
1.88
Wt.
each
(lbs.)
2.64
4.86
10.46
16.52
GRADE 100 CHAIN ATTACHMENTS
Swivel Lodelok Hook
• Permits positioning of load before lift
• Open design permits multi hardware use
(Chain, Nylon & Wire Rope)
• Interlocking tip gives added protection
• Forged from Alloy Steel
• New “I” beam no catch point design
• 100% proof tested
• Designed to meet ASTM A952 & EN1677
• For welded 7/32" chain sling use 9/32" eye hook
Swivel Lodelok Hook
Chain size
(in.)
(mm)
9/32
7
3/8
10
1/2
13
5/8
16
WLL*
(lbs.)*
4,300
8,800
15,000
22,600
Product
code
676005
676010
676015
676020
Replacement
Latch And
Hook Kits
A
1.50
1.75
2.00
2.75
B
1.33
1.63
1.76
2.38
Dimensions (inches)
C
D
E
F min
6.79
1.00
3.89
1.563
8.77
1.25
5.03
2.250
10.54
1.75
6.68
2.813
12.80
2.00
8.04
3.125
Replacement Latch Kits
– Eye Sling Hooks
Kit includes all hardware for
Chain
Current Style Latch
size
Product Code
(in.)
7/32
—
9/32
595523
3/8
595525
1/2
595528
5/8
595529
3/4
595530
Clevlok Sling Hooks.
– Eye Sling Hooks
Kit includes all hardware for
Chain
Current Style Latch
size
Product Code
(in.)
9/32
4X658718
3/8
4X658719
1/2
4X658720
5/8
4X658721
31
G
1.19
1.25
1.63
1.88
H
0.50
0.63
0.75
1.00
Wt.
each
(lbs.)
2.61
5.09
11.03
18.09
GRADE 100 CHAIN ATTACHMENTS
Master Oblong Link
• Designed for Herc-Alloy 1000 chain and components
• Gray powder coated finish
• Used for mechanical and welded sling assemblies
• Meets or exceeds the requirements of ASTM A952
• 100% proof tested
Oblong Master Link
Trade
size
(in.)
13/32
1/2
3/4
1
1 1/4
1 1/2
1 3/4
Product
code
555231
555232
555235
555238
555240
555243
555246
Working
load limit*
(lbs.)*
5,400
8,600
17,600
30,000
45,200
70,600
105,900
Link Size (Inches)
Diameter
Inside
Inside
material
length
width
A
B
C
0.406
3.000
1.500
0.512
5.000
2.500
0.750
5.500
2 .750
1.024
7.000
3.500
1.260
8.750
4.375
1.500
10.500
5.250
1.750
12.000
6.000
Type & Size of Chain Sling
on which used
Single
Double
Triple
Quad
type
type
type
type
S&C
7/32
7/32
—
—
9/32
9/32
7/32
7/32
3/8
3/8
9/32
9/32
1/2 or 5/8
1/2
3/8
3/8
3/4
5/8
1/2
1/2
—
3/4
5/8
5/8
—
—
3/4
3/4
Weight
each
(lbs.)
0.33
0.81
2.08
4.59
9.31
15.6
24.4
Oblong Master Link Sub-Assembly*
for triple and quad branch chain slings
Trade
Working
Oblong Master
Master Coupling
size
Product load limit*
Link Size (In.)
Link Size (In.)
(in.)
code
(lbs.)*
A
B
C
D
E
F
1/2
555274
7,000
0.512
3.000
1.500
0.344
0.625
1.125
3/4
555275
11,200
0.750
5.500
2.750
0.468
0.875
1.563
1
555276
22,900
1.000
7.000
3.500
0.656
1.250
2.250
1 1/4
555277
39,000
1.250
8.750
4.375
0.906
1.750
3.125
1 1/2
555278
58,700
1.500
10.500
5.250
1.125
2.250
4.000
13/4
555279
91,700
1.750
12.000
6.000
1.250
2.375
4.375
*Consisting of oblong master link and two welded master coupling links.
32
Triple
Size
7/32
9/32
3/8
1/2
5/8
3/4
Quad
Size
7/32
9/32
3/8
1/2
5/8
3/4
Weight
each
(lbs.)
1.04
2.08
4.59
9.16
15.66
24.44
GRADE 100 CHAIN ATTACHMENTS
Shortening Hook Specifications
For securing suspended chains, shortening chains and adjusting chains to form a loop which
must not tighten. Full load of the chain may be used.
Chain Size Product
ins.
Code
9/32
15111
3/8
15102
1/2
15104
5/8
15106
3/4
15108
e
b
a
d1
d2
g
lb/pc
3.46
4.53
5.79
6.97
8.27
1.97
2.68
3.54
4.33
5.28
1.54
1.97
2.52
3.15
3.70
0.94
1.22
1.54
1.85
2.20
0.43
0.55
0.59
0.67
0.94
0.35
0.51
0.59
0.67
0.83
1.10
2.16
4.62
8.98
15.6
33
GRADE 120 CHAIN ADVANTAGES
ADVANTAGES
OF GRADE 120:
1. 50% Higher Work Load Limits
compared to Grade 80. Allowing a downsizing of chains.
2. Weight Reduction—
Downsizing of chains results in
lower weights for chain slings.
3. Improved Wear Resistance—
Due to the special form of the
profile chain, a larger contact
area is achieved between the
bearing surfaces of the links.
This is a real advantage in
abrasive environments.
4. Bending Resistance The G120 profile chain has up
to 38% higher moment of
resistance compared to regular round-link chains of the
same diameter. Therefore, the
chain can withstand bending
forces better than round-link
chains.
5. Color-Coded Corrosion
Protection—G120 has a powder coated finish in blue providing easy identification and
corrosion protection.
6. 6. G120 Meet or Exceeds
NACM/ASTM-Test Requirements.
Chain
Size
WLL
Breaking
LL (lbs.)
Product
Code
Nominal
Thickness
d
Pitch
t
Width
Inside
b1 min.
Width
Outside
b2 max.
Weight
9/32
5,200
20,800
NI 720
.276 (7 mm)
.846
.378
1.134
.907
3/8
10,600
42,400
NI 1020
.394 (10 mm)
1.280
.532
1.457
1.814
1/2
17,900
71,600
NI 1320
.512 (13 mm)
1.634
.717
1.894
3.225
Chain
Size
ins.
WLL (lbs.) at Various Angles
1-Leg
3 & 4-Leg
2-Leg
90 °
30 °
45 °
60 °
30 °
45 °
60 °
9/32
5,200
5,200
7,400
9,000
7,800
11,000
13,500
3/8
10,600
10,600
15,000
18,400
15,900
22,500
27,500
1/2
17,900
17,900
25,300
31,000
26,900
38,000
46.500
Actual Chain
Temp.
- 40 ° to 400 ° F.
Reduction Factor
1
For asymmetrical load distribution,
use sling leg value for all angles or 2-leg slings;
Use 2-leg values for all 3 and 4-leg slings
Angle
30 °
45 °
60 °
30 °
45 °
60 °
Load factor with
symmetrical load
distribution
1
1.4
1.7
1.5
2.1
2.6
1
1
1
1
1.4
1.7
Reduction Factor
1
34
0.7
0.5
GRADE 120 CHAIN LINKS AND HOOKS
Product
Code
M1320
M1820
M2620
Enlarged Master Links M-G120
Master Link For Single Leg Slings Or End Link
Single Leg
WLL
Sling Ins.
(lbs.)
d
t
w
s
9/32
5,200 0.551 4.724 2.756 0.394
3/8
10,600 0.787 6.299 3.740 0.551
1/2
17,900 1.063 7.480 4.331 0.787
Weight
lb./pc.
0.97
2.67
5.84
Enlarged Master Link Assemblies VM-G120
Master Link Assemblies for Multi-Leg Slings
Product Consisting Dbl. Leg 3 & 4 Leg WLL
Weight
Code
of
Sling ins.Sling ins.60kg/lb e
lb/pc
VM720 M18+2B13
9/32
9,000 8.425 3.42
VM10720 M26+2B16
3/8
9/32 18,400 10.236 7.43
VM131020 M32+2B20
1/2
3/8 31,000 12.402 13.23
VM1320 M36+2B26
1/2 46,500 16.34 24.52
d
.787
1.063
1.300
1.5
M-Link
t
w
6.299 3.740
7.480 4.331
9.055 5.118
10.827 5.906
Connex-Connecting Link C-G120
For Master Link To Chain Or Chain To Components
Product WLL
b
Weight
Code
(lbs.)
e
c
s
d
Max.
g
lb./pc.
C720
5,200 2.008 .433 .516 .354 1.831 .642
.26
C1020 10,600 2.772 .630 .787 .496 2.579 .846
.73
C1320 17,900 3.740 .827 .945 .657 3.307 1.024 1.54
Eye Sling Hook HS-G120
General Purpose Hook With Forged Safety Latch
Product
Code
HS720
HS1020
HS1320
WLL
Weight
(lbs.)
e
h
a
d1
d2
g1
b
lb./pc.
5,200 3.976 1.102 .748 0.984 0.43 1.024 3.465 1.10
10,600 5.158 1.299 1.024 1.339 0.630 1.220 4.272 2.38
17,900 6.260 1.654 1.299 1.693 0.75 1.535 5.264 4.03
Self Locking Shortening Hook XS-G120
Shortening Applications Where Chain Must Be Secure
Product WLL
Weight
Code
(lbs.)
e
b
d1
d2
g
lb./pc.
XS720 5,200 4.685 3.039 .984
.472 .394
1.98
XS1020 10,600 5.787 3.976 1.280 .630 .512
3.31
XS1320 17,900 7.303 4.949 1.575 .787 .669
6.17
Grab Hook P-G120
May Be Used As A Shortening Device
Product WLL
Code
(lbs.)
e
b
d1
P720
5,200 2.776 2.291 .787
P1020 10,600 3.465 2.988 .866
P1320 17,900 4.449 3.976 1.024
35
d2
.453
.591
.709
g
.413
.512
.669
Weight
lb./pc.
.46
1.43
3.00
ENDURANCE HIGH PERFORMANCE CHAIN
Endurance Chain Mesh Slings
Specialty Slings for rugged applications—Widely used in metalworking shops, and stevedoring when abrasive conditions or hot environments damage and destroy synthetic slings.
Chain
Size
(in.)
7/32
9/32
3/8
1/2
Parts
of
Chain
3
4
5
6
3
4
5
6
3
4
5
6
2
3
4
Sling
Width
1-1/2
2
2-1/2
3
2-1/8
2-3/4
3-3/8
4
3-1/4
4-3/8
5-3/8
6-1/2
3
4-1/2
6
Terminal Dimensions (ins.)
D
2-3/4
3
3-1/2
3-3/4
2-3/4
3
3-1/2
3-3/4
3-1/2
4-3/8
4-3/8
5-1/4
3-1/2
4-3/8
5-1/4
IL
4-1/8
4-1/2
5-1/4
5-5/8
4-1/8
4-1/2
5-1/4
5-5/8
5-1/4
6-1/2
6-1/2
7-7/8
5-1/4
6-1/2
7-7/8
TL
6-3/4
7-1/8
8
8-1/4
6-3/4
7-1/8
8
8-1/4
6-7/8
8-1/8
8-3/8
9-3/4
6-7/8
8-3/8
9-3/4
TW
4-3/4
5
5-1/2
5-3/4
4-3/4
5
5-1/2
5-3/4
6
6-3/8
7-3/8
8-1/4
5
6-3/8
7-3/4
CL
9
9-3/8
10-1/8
10-5/8
9
9-3/8
10-1/8
10-5/8
CW
7-1/8
7-1/4
7-3/4
8-1/4
7-1/8
7-1/4
7-3/4
8-1/4
T
3/8
3/8
3.8
3.8
1/2
1/2
1/2
1/2
3/4
3/4
3/4
3/4
1
1
1
H
1-1/4
1-1/4
1-1/4
1-1/4
1-3/4
1-/34
1-3/4
1-3/4
2-1/4
2-1/4
2-1/4
2-1/4
3-1/8
3-1/8
3-1/8
NOTE: Length tolerance + or - 2 chain links so plane is maintained.
36
5 Ft. Type 2 Weight/Ft.
Weight (lbs.)
(lbs.)
10
1.3
12
1.8
14
2.2
17
2.7
14
2.2
18
3.0
22
3.7
26
4.5
30
4.4
41
5.8
55
7.3
59
8.8
33
5.2
50
7.7
62
10
COIL CHAIN—STRAIGHT
37
COIL CHAIN—TWISTED
38
DOUBLE LOOP CHAIN
39
DOUBLE LOOP CHAIN—SPECIAL WELL CHAIN
40
TRAILER SAFETY CHAIN
41
TRAILER SAFETY CHAIN
42
JACK CHAIN—SINGLE
43
JACK CHAIN—DOUBLE
44
LOCK LINK CHAIN—SINGLE LOOP
45
MACHINE CHAIN—STRAIGHT
46
MACHINE CHAIN—TWIST
47
PASSING LINK CHAIN
48
PLUMBERS CHAIN
49
STEEL SASH CHAIN
50
PROOF COIL—REGULAR LINK
51
PROOF COIL—LONG LINK
52
PROOF COIL—PAILS, REELS
53
PROOF COIL—PAILS, REELS
54
PROOF COIL—DRUMS, PAILS
55
TIEDOWNS—HIGH TEST CHAIN
56
TIEDOWNS—TOW, BINDER CHAIN
57
TIEDOWNS—TOW, BINDER CHAIN
58
GRADE 70 CHAIN AND HOOKS
Grade 70 Chain
Grade 70 Chain
Chain
size
(ins.)
1/4
5/16
3/8
7/16
1/2
WLL
(lbs.)
3,500
4,500
7,100
6,900
12,000
Half Drum
Product
Code
UPC
678531
32636
678532
32798
678533
32834
678534
32905
678535
33029
Weight
(lbs.)
per 100
Std. Drum Lge. Drum Feet Per Container
Product
Product
Half
Std.
Lge.
Code
Code
Drum Drum Drum
678541
678541
400
800
1,400
678542
678542
275
550
900
678543
678543
200
400
650
678544
678544
150
300
450
678545
678545
100
200
350
74
100
156
204
259
Grade 70 Clevis Grab Hook
Grade 70 Clevis Grab Hook
Chain
size
(ins.)
5/16
3/8
WLL
(lbs.)
4,700
6,600
Product
Code
M805T
M806T
W
.38
.45
D
2.31
2.63
H
.44
.50
L
4.0
4.5
P
.39
.49
R
2.34
2.66
Weight
(lbs.)
per 100
.75
1.10
Grade 80 Alloy Clevis Grab Hook
Grade 80 Alloy Clevis Grab Hook
Chain
size
1/4
5/16
3/8
7/16
1/2
5/8
WLL
(lbs.)
3,500
4,500
7,100
6,900
12,000
18,100
Product
Code
M804A
M805A
M806A
M807A**
M808A
M810A
W
5/16
3/8
29/64
1/2
19/32
3/4
D
H
1-15/16
3/8
2-9/32
7/16
2-5/8
1/2
3
9/16
3-7/16 21/32
4-5/16 25/32
** Grade 63
59
L
3-1/4
3-31/32
4-1/2
5-1/32
5-23/32
6-7/8
P
R
21/64 1-7/8
25/64 2-3/8
1/2
2-5/8
1/2
3
19/32 3-5/16
3/4 3-15/16
Weight
(lbs.)
.38
.62
.96
1.46
2.02
3.75
Std. Ind.
Pack
30
30
30
20
10
10
LOAD BINDER SAFE OPERATING PROCEDURES
Load Binder Safe Operating Procedures
WARNING!!!
Death / injury can occur from improper use
or maintenance of tie-down equipment.
To avoid injury:
•
•
•
•
•
•
•
•
•
Inspect before use - remove from service if cracked, work, or deformed.
Do not overload - load binders develop approximate working load with hand effort.
Do not use handle extender on load binder(s).
Do not use binder components for overhead lifting.
Load binding systems store energy which can release suddenly.
Operate only by hand from a firm standing position.
Operate handle cautiously.
Stay clear of handle path; handle may release suddenly.
Follow Operating Instructions.
Operating Instructions:
•
•
•
•
•
•
•
•
•
Follow DOT Federal Motor Carrier Safety regulations 392.9, 393.100, and 393.102.
Inspect before use. Replace worn and deformed binders. Lubricate pivot and swivel points for
optimum performance.
Do not operate with anyone on load.
Always apply binder in a straight line hook to hook manner without bending and such that handle goes down when securing load.
Tighten binders before moving and recheck frequently.
Do not exceed Working Load Limit shown on binder.
Do not use cheater bar or handle extension as such use can overload binder system and result
in injury.
Secure handle down with a positive retaining method.
Release handle / load with extreme care. Make sure all personnel are clear. Lever binder handles can snap back over center. Use open palm under handle and push up.
60
SCC LOAD BINDERS
SCC Load Binders
SCC loadbinders meet all DOT/CVSA/CHP requirements. Special hook construction supports the
load of the chain and will not bind. Loadbinders are heat treated and proof tested with forged heat
treated hooks. The Working Load Limit is permanently marked on handle. Ratchet binders feature
special links with controlled flash weld. All SCC ratchet load binders are painted with yellow enamel.
Not approved for overhead lifting.
The SCC QuikBinder™ is easier to install than standard ratchet load binders. The 3-position pawl
offers the user a choice of ratchet extension, ratchet take-up or a “free spin” setting for fast adjustment in either direction. A load can be secured in half the time. It is available in two popular sizes
and features a vinyl coated barrel for a strong, comfortable grip.
The folding handle make SCC’s QuikBinder™ safer (no handle sticking out) and more convenient to
use. Simply fold the handle down after the load is secure or when storing the QuikBinder™ on your
cab rack. Just as strong but faster, safer and more functional than standard ratchet binders.
The QuikBinder™ can be locked to the chain with a long shank padlock, making it tough to tamper
with the binder, assembly or the load. Padlocks with programmable combinations are available.
SCC QUICKBINDER™ of SCC Chain
Product
Code
H5125-4158
H5125-4258
For Chain Size
S7
5/16
3/8
S4
3/8
1/2
Working
Load Lim it
(lbs.)
5,400
9,200
Take Up
(ins.)
8.0
8.0
Handle
Length
(ins.)
9.5
9.5
61
Weight
(lbs).
11.40
13.90
CM Forged LEVER LOAD BINDERS
CM Forged Load Binders
•
•
•
•
•
•
•
•
•
Dixie Industries lever load binders are made to the highest manufacturing standards. All binders
meet or exceed CVSA Cargo Securement Guidelines and FMSCA.
Hooks are forged from micro-alloy steel and are designed to yield before catastrophic failure.
Each forged part is permanently marked with a date code providing traceability to heat of steel.
Dixie / CM name forged on all parts. Tells you where and whom you can ask for help or information.
Dixie Industries keeps all files and test information supporting the products they manufacture for ten
years. Load binders without the name of the manufacture are not traceable!
All hooks swivel. Fully articulated movement allow straight line pull, both hooks - a Dixie Innovation.
Short reach hooks allow you to grab 1 more chain link for tighter take-up - another Dixie Innovation!
Under heavy loads, traditionally designed lever binders have a tendency to spread at the ears, jamming the clevis mechanism. Dixie Industries' unique tongue design operates 180 degrees from traditional binders avoiding any possibility of spreading or jamming the mechanism.
Forged "ball" on the end of the handle for a more sure hand gripping surface. A hole is provided at
the end of the handle for securement as per new DOT requirements. The handle angle is designed
to allow room for a gloved hand grip.
All components are made in the USA - American workers forging American steel, assembling American products in their American plant in Chattanooga, TN.
Product
Code
48304
48305
48306
48769
For Chain Size
G30
1/4
3/8
1/2
3/8
G43
1/4
3/8
1/2
3/8
G70
5/16
3/8
3/8
Working
Load Lim it
(lbs.)
2,600
5,400
9,200
7,100
Take
Up
(ins.)
3.75
4.50
4.75
4.50
Handle
Length
(ins.)
11.25
16.12
16.62
16.62
62
Weight
(lbs).
3.0
8.1
10.6
8.1
CM FORGED RATCHET BINDERS
CM Forged Ratchet Binders
•
•
•
•
•
•
•
•
•
•
•
•
Dixie ratchet binders are built to exceed the highest military and professional specifications, including
CVSA Cargo Securement Guidelines, Federal Highway, and DOT requirements.
Dixie forges each ratchet component from pure alloy steel bar.
Ratchet binders provide superior ergonomics to the traditional lever binder by requiring less physical
strength to attach and remove.
The handle is purposely designed loose using self-locking one-way bolts. This loose design allows
mud, snow, ice or any other clogging substance to be easily removed from the ratchet mechanism
by striking with a hammer or other tool.
To insure quality, each individual ratchet binder, as part of the manufacturing process, is proof tested
to 50% of the Minimum Breaking Strength (MBS) according to NACM criteria.
All 1 inch ratchet binders feature oversized eyebolts and barrels providing additional support material
for wear and tear.
Dixie ratchet gears are permanently welded to the barrel while many others are simply roll pinned.
With our ratchet, there is no pin to fall out.
Dixie upset forged all our barrels, providing deeper and more consistent threads for longer life.
Acme threads provide fasted take up, stay put, and won't back off.
Hooks forged from micro-alloy steel, designed to yield before catastrophic failure.
MADE IN USA - All our products are forged with USA, our name, product tract codes on each forged
parts, and Working Load Limit (WLL) as required by many laws and manufacturing best practices.
Dixie proudly stands beside you for the working life of our product.
Forged Ratchet Binders
Product
Code End Fittings
48364
Hook/Hook
Eye/Eye
48811 (no hooks)
Eye/Eye
48363 (no hooks)
48810
Hook/Hook
48360
Hook/Hook
48365
Hook/Hook
48366
Hook/Hook
48367
Hook/Hook
G30
1/4
G43
1/4
G70
-
Working
Load Lim it
(lbs.)
2,600
-
-
-
5,400
3/8
3/8
3/8
1/2
5/8
3/8
3/8
3/8
1/2
5/8
For Chain Size
5/16
3/8
5/16
3/8
1/2
13,000
5,400
7,100
5,400
9,200
13,000
63
CM RATCHET BINDERS
CM Ratchet Binders
• Single handle fits both size ratchets, reduces cost
• Loss Prevention, difficult to remove from load
• Reduce overall weight, no need for additional handles
Body and Handle Ordered Separately. Additional End
Fittings Available. Load Security: properly tensioned
ratchet barrel, with the handle removed, provides
greater load security, making it less likely for your load
to be stolen. Reduce your overall weight - no need for
additional handles.
Rem ovable Handle Ratchet Binder
Rem ovable Handle Ratchet Binder
Product
Code
46565
46566
46565H
End
Fittings
Body only
Body only
Handle only
Chain Grade & Sizes
(in.)
G30
G43
G70
3/8
3/8
5/16
1/2
1/2
3/8
N/A
N/A
N/A
WLL (lbs.)
5,400
9,200
N/A
Handle Barrel OD (in) Screw Take Up
(in.)
Product Length (Dia. x Length) Dia. (in.)
G30
G43
G70
Code
(in.)
46565
N/A
3/8
3/8
5/16
46566
N/A
1/2
1/2
3/8
46565H
14
N/A
N/A
N/A
64
WLL
(lbs.)
5,400
9,200
N/A