Written test to follow safe manual handling training

This course is designed as an introduction to safe lifting for use by
employers with their employees
It does not negate the need for the employer to
a. Carry out and record risk assessments for manual handling if the company
employs more than 5 staff
b. Provide practical training to staff on manual handling and assess these staff to
ensure they have understood the systems in place and the methods to be used
when carrying out manual handling tasks in their own place of work
It will cover
1. Manual handling risk factors and how injuries can occur;
2. How to carry out safe manual handling, including good handling technique;
3. Appropriate systems of work for the individual's task and environment;
4. Use of mechanical aids
5. Examples of practical work to allow the trainer to identify and put right anything
the trainee is not doing safely.
Part 5 above will be assessed by the management of the trainee’s workplace
Instructions
The trainee should read through the text and then be given practical training in safe
lifting basic and any particular lifting operations that relate to specific work carried
out in the workplace (e.g. lifting bags of fertiliser, mower units, hole changing etc.).
After suitable training and reading of the this training text the trainee should attempt
a short test on safe lifting and then assuming he/she passes this written test and has
been given a suitable level of practical instruction that covers the work expected of
the trainee and has passed a written test that checks the trainees knowledge both
trainer and trainee should sign the record of training and a copy should be given to
the trainee and a copy returned in the trainees training records.
Information for the employer
What should a manual handling training course involve?
The relevant legislation is the Manual Handling Operations Regulations 1992 (as
amended). With regards to training, the guidance to the Regulations states:
"Section 2 of the Health and Safety at Work Act 1974 and regulations 10 and 13 of
the Management of Health and Safety at Work Regulations 1999 require employers to
provide their employees with health and safety information and training. This should
be supplemented as necessary with more specific information and training on manual
handling injury risks and prevention, as part of the steps to reduce risk required by
regulation 4(1) (b) (ii) of the Regulations.
"The risk of injury from a manual handling task will be increased where workers do
not have the information or training necessary to enable them to work safely. For
example, if they do not know about any unusual characteristics of loads or about the
system designed to ensure their safety during manual handling, this may lead to
injury. It is essential that where, for example, mechanical handling aids are available,
training is provided in their proper use.
"The provision of information and training alone will not ensure safe manual handling.
The first objective in reducing the risk of injury should be to design the manual
handling operations to be as safe as is reasonably practicable. This will involve
improving the task, the working environment and reducing the load weight as
appropriate. Where possible the manual handling operations should be designed to
suit individuals, not the other way round. Effective training has an important part to
play in reducing the risk of manual handling injury. It should not be regarded as a
substitute for a safe system of work.
"Employers should make sure that their employees understand clearly how manual
handling operations have been designed to ensure their safety. Employees, their
safety representatives and safety committees should be involved in developing and
implementing manual handling training, and monitoring its effectiveness. This will
include, for example, checking that any training is actually being put into practice and
that accident rates have reduced. As with assessors, if in-house personnel are used to
act as trainers, suitable checks should be made to ensure that they have understood
the information given to them and have reached an adequate level of competence.
HSE does not publish prescriptive guidance on what a 'good' manual handling training
course should include or how long it should last. However, in general, courses should
be suitable for the individual, tasks and environment involved, use relevant examples
and last long enough to cover all the relevant information, Such information is likely
to include advice on:
1. Manual handling risk factors and how injuries can occur;
2. How to carry out safe manual handling, including good handling technique;
3. Appropriate systems of work for the individual's task and environment;
4. Use of mechanical aids
5. Practical work to allow the trainer to identify and put right anything the trainee is
not doing safely.
Employers should ensure they keep sufficient records to show who has been trained,
when the training was carried out and what the content of the course was. Employers
should establish a planned training programme to ensure all staff receive basic
training, with updates as required. This programme should also cover new starters to
try to ensure training takes place either before or as close to starting a new job as
possible. Managers may also wish to monitor sickness absence and near-miss
reporting as one way to assess the effectiveness of the training.
Employees should be trained to recognise loads whose weight, in conjunction with
their shape and other features, and the circumstances in which they are handled,
might cause injury. Simple methods for estimating weight on the basis of volume may
be taught. Where volume is less important than the density of the contents, as for
example in the case of a dustbin containing rubbish, an alternative technique for
assessing the safety of handling should be taught, such as rocking the load from side
to side before attempting to lift it.
In general, unfamiliar loads should be treated with caution. For example, it should not
be assumed that apparently empty drums or other closed containers are actually
empty. They should be tested first, for example by trying to raise one end. Employees
should be taught to apply force gradually until either too much strain is felt, in which
case the task should be reconsidered, or it is apparent that the task is within the
handler's capability.
When workers are given appropriate training, it is important to ensure that
supervisors and other more senior staff are also aware of the good practices that
have been recommended, and that they regularly encourage the workforce to adopt
appropriate techniques and ensure they continue to be used.
References
Manual handling. Manual Handling Operations Regulations 1992 (as amended).
Guidance on Regulations L23 (Third edition) HSE Books 2004 ISBN 0 7176 2823 X ,
price £8.95
A free leaflet is also available Getting to grips with manual handling: A short guide for
employers INDG143(rev2).
Both publications are available from HSE Books.
Making the best use of lifting and handlings aids
http://www.hse.gov.uk/pubns/indg398.pdf
Manual handling. Manual Handling Operations Regulations 1992 (as amended)
http://www.hse.gov.uk/pubns/priced/l23.pdf
Is there a guide to help with manual handling assessments?
HSE have produced the manual handling assessment chart (MAC) to assist employers
with their manual handling assessments. The following information has been taken
from the leaflet Manual handling assessment charts (INDG383):
Work-related musculoskeletal disorders (MSDs), including manual handling injuries,
are the most common type of occupational ill health in the UK and their prevention is
a priority for HSC/E. It is important to remember that:
1. Things can be done to prevent MSDs;
2. Preventative measures are cost-effective;
3. All MSDs cannot be prevented; so early reporting of symptoms, proper treatment
and suitable rehabilitation is essential.
The steps to follow
The Manual Handling Operations Regulations 1992 (as amended) establish a clear
hierarchy of measures for dealing with risks from manual handling.
These are:
1. Avoid hazardous manual handling operations so far as reasonably practicable
2. Assess any hazardous manual handling operations that cannot be avoided
3. Reduce the risk of injury so far as reasonably practicable
The MAC
The Manual Handling Assessment Charts (MAC) is a new tool designed to help health
and safety inspectors assess the most common risk factors in lifting (and lowering),
carrying and team handling operations. Employers, safety officers, safety
representatives and others may also find the MAC useful to identify high-risk manual
handling operations and help them complete their risk assessments.
Structure of the MAC
There are three types of assessment that can be carried out with the MAC:
1. lifting operations;
2. carrying operations;
3. team handling operations.
For each type of assessment there is an assessment guide and a flowchart.
Note:
The MAC is not appropriate for some manual handling operations, for example those
that involve pushing and pulling. Its use does not comprise a full risk assessment (for
advice on how to do a full assessment, see L23 Manual handling). You must consider
individual and psychosocial issues when completing the score sheet. Also, the MAC is
not designed to assess risks from workplace upper limb disorders.
The MAC tool can be found on the HSE website. Copies of INDG383 are available from
HSE Books.
Is there a maximum weight a person can lift during their work?
The Manual Handling Operations Regulations 1992 (as amended) set no specific
requirements such as weight limits.
The ergonomic approach shows clearly that such requirements are based on too
simple a view of the problem and may lead to incorrect conclusions. Instead, an
ergonomic assessment based on a range of relevant factors is used to determine the
risk of injury and point the way to remedial action.
The Regulations establish the following clear hierarchy of control measures:
1. Avoid hazardous manual handling operations so far as is reasonably practicable,
for example by redesigning the task to avoid moving the load or by automating
or mechanising the process.
2. Make a suitable and sufficient assessment of any hazardous manual handling
operations that cannot be avoided.
3. Reduce the risk of injury from those operations so far as is reasonably
practicable. Where possible, you should provide mechanical assistance, for
example a sack trolley or hoist. Where this is not reasonably practicable, look at
ways of changing the task, the load and working environment.
Modern medical and scientific opinion accepts the scale of the problem and stresses
the importance of an ergonomic approach to remove or reduce the risk of manual
handling injury. Ergonomics is sometimes described as 'fitting the job to the person,
rather than the person to the job'. The ergonomic approach looks at manual handling
as a whole. It takes into account a range of relevant factors, including the nature of
the task, the load, the working environment and individual capability and requires
worker participation.
When a more detailed assessment is necessary it should follow the broad structure
set out in Schedule 1 to the Regulations. The Schedule lists a number of questions in
five categories:
1. the task;
2. the load;
3. the working environment;
4. individual capability (this category is discussed in more detail under regulation
4(3) and its guidance); and
5. other factors, for example use of protective clothing.
Each of these categories may influence the others and none of them can be
considered on their own. However, to carry out an assessment in a structured way it
is often helpful to begin by breaking the operations down into separate, more
manageable items.
Manual Handling course
What is manual handling?
Manual handling involves pushing, pulling, lifting etc. of items in the workplace. This
might be bags of fertiliser, pushing wheel barrows, pulling hose lines etc.
Instructions
This course sets out to provide you with basic training in manual handling operations.
You should read the text as you will be expected to take and pass a short test at
when you state you have read and understood this text.
In addition your employer will ensure you are trained in the basic tasks involving
manual handling at you place of work and then assess you to ensure you have
understood these.
Reading text for the manual handling course
One of the biggest causes of back injury at work is lifting or handling objects
incorrectly.
Learning and following the correct method for lifting and handling heavy loads can
help to prevent injury and avoid back pain etc.
Most problems can be avoided by the following simple steps
1. Think before you lift
Is it possible to avoid lifting, pulling etc. the load or can you use a mechanical aid
Think about mechanisation and using handling aids. For example:
A pallet truck;
An electric or hand-powered hoist;
Lift truck.
Wheel barrow
Etc.
If you have to lift or move an item you should
a. Check you can manage the lift (try e.g. by rocking an item etc.) before you fully
commit to the move
b. If in doubt get someone to help you
c. Consider using a lifting/moving aid (wheel barrow etc.)
Plan the lift. Where is the load going to be placed? Use appropriate handling aids
where possible. Will help be needed with the load? Remove obstructions, such as
discarded wrapping materials. For long lifts, such as from floor to shoulder height,
consider resting the load mid-way on a table or bench to change your grip on it.
2 . Adopt a stable position
Your feet should be apart with one leg slightly forward to maintain balance (alongside
the load if it's on the ground). Be prepared to move your feet during the lift in order
to maintain a stable posture. Wearing over-tight clothing or unsuitable footwear, such
as heels or flip flops, may make this difficult.
3 . Ensure a good hold on the load
Where possible; hug the load close to the body. This may be a better option than
gripping it tightly with the hands only.
4. Keep the load close to the waist
Keep the load close to the waist for as long as possible while lifting. The distance of
the load from the spine at waist height is an important factor in the overall load on
the spine and back muscles. Keep the heaviest side of the load next to the body. If
closely approaching the load isn't possible, try to slide it towards the body before
trying to lift it.
5. Don't bend your back
A slight bending of the back, hips and knees at the start of the lift is preferable to
either fully flexing the back (stooping) or fully flexing the hips and knees – in other
words, fully squatting.
6. Don’t flex the back any further while lifting
This can happen if the legs begin to straighten before starting to raise the load.
7. Don't twist
Avoid twisting the back or leaning sideways especially while the back is bent. Keep
your shoulders level and facing the same direction as the hips. Turning by
moving your feet is better than twisting and lifting at the same time.
8. Keep your head up
Keep your head up when handling the load. Look ahead, not down at the load once it
has been held securely.
9. Move smoothly
Don't jerk or snatch the load as this can make it harder to keep control and can
increase the risk of injury.
10. Know your limits
Don't lift or handle more than you can easily manage. There's a difference between
what people can lift and what they can safely lift. If you're in doubt, seek advice or
get help.
11. Lower down, and then adjust
Put the load down and then adjust. If you need to position the load precisely, put it
down first, and then slide it into the desired position.
Good handling technique for pushing and pulling
Here are some practical points to remember when loads are pushed or pulled.
Estimation of weight
Before attempting to move or lift an item check its weight first e.g. if it’s a barrel try
tipping it slightly to one side to get a feel for the weight before you try to move it.
Also an idea can be obtained by a mathematical estimation e.g. using volume. For
example water weights 1kg for ever litre. Therefore a container of 25 litres of liquid
will as a rough estimate weight 25kg.
Handling devices. Aids such as barrows and trolleys should have handle heights that
are between the shoulder and waist. Devices should be well maintained with wheels
that run smoothly. The law requires that equipment is maintained.
Force. As a rough guide the amount of force that needs to be applied to move a load
over a flat, level surface using a well-maintained handling aid is at least 2% of the
load weight. For example, if the load weight is 400 kg, then the force needed to move
the load is 8 kg. The force needed will be larger, perhaps a lot larger, if conditions are
not perfect (e.g. wheels not in the right position or a device that is poorly maintained).
The operator should try to push rather than pull when moving a load, provided they
can see over it and control steering and stopping.
Slopes. Employees should get help from another worker whenever necessary, if they
have to negotiate a slope or ramp, as pushing and pulling forces can be very high. For
example, if a load of 400 kg is moved up a slope of 1 in 12 (about 5°), the required
force is over 30 kg even in ideal conditions – good wheels and a smooth slope. This is
above the guideline weight for men and well above the guideline weight for women.
Uneven surfaces. Moving an object over soft or uneven surfaces requires higher
forces. On an uneven surface, the force needed to start the load moving could
increase to 10% of the load weight, although this might be offset to some extent by
using larger wheels. Soft ground may be even worse.
Stance and pace. To make it easier to push or pull, employees should keep their
feet well away from the load and go no faster than walking speed. This will stop
them becoming too tired too quickly.
Is there a maximum weight a person can lift during their work?
The Manual Handling Operations Regulations 1992 (as amended) set no specific
requirements such as weight limits. How much a person should lift is dependent on
their ability, how often they must lift or move the item, the conditions etc. This is why
the employer must assess the risks of all manual handling operations.
Written test to follow safe manual handling training
1. Where should a load be carried (circle the answer that is correct)
a. Close to the waist
b. Close to the chest
2. What is the maximum weight you can lift (circle the answer that is
correct)
a. 20kg
b. 30kg
c. There is no set weight
3. Why should you check the follow space before lifting (circle the answer
that is correct)
a. To avoid trip hazards and slip hazards
b. To ensure you can get to the drop off point quickly
4. What should you do if you are unsure about been able to lift a weight
(circle the answer that is correct)
a. Seek help
b. Use a wheel barrow
5. When lifting and carrying a load the head should be (circle the answer
that is correct)
a. Upright
b. Lowered
6. When lifting you should (circle the answer that is correct)
a. Lift as quickly as possible to get the load up
b. Lift slowly
7. List 3 operations carried out at your place of work that involves manual
handling (lifting, pushing, pulling etc.
a.
b.
c.
8. Name two types of mechanical aid that can be used to reduce the risks
from manual handling at your place of work
a.
b.
9. When trying to move a load it is safer to (circle the answer that is correct)
a. Push the load
b. Pull the load
10. Pushing a load uphill is a problem because (circle the most important
answer)
a. You will get tired quickly
b. The weight increases as the slope increases
c. The load might fall off of the wheel barrow
11. A 250 litre barrel of oil will weigh (circle the answer that is correct)
a. 250 Kg
b. 25 kg
c. 2500kg
Trainer feedback
Well done you have completed this test correctly
You have made errors in the following areas
tick
tick and list errors below
Please study the text on manual handling again and ensure you improve
understanding in the above areas ready to retake this test.
Name (Print)
Signed trainee
Date
Name (Print)
Signed trainer
Date
Safe lifting training record (to be printed off and used as evidence of safe
manual handling training)
Name of organisationI agree that I have covered the following at my place of work
1. Manual handling risk factors and how injuries can occur, covered by training and
a written test.
2.
How to carry out safe manual handling, including good handling technique;
covered by training and a written test.
3. Appropriate systems of work for my individual tasks and environment
4. Use of mechanical aids - I have been show any mechanical aids that are used at
work to carry out manual handling , e.g. sack trucks, wheel barrows, hosts,
lifting hooks etc.
5. Practical work and assessment to allow the trainer to identify and put right
anything the trainee is not doing safely.
Name (Print)
Signed trainee
Date
Name (Print)
Signed trainer
Date