Scrap Collector
TM
Job:
Model S914
Item No.:
A Scrapping, Pre-Flushing and
Food Waste Collecting System
n Standard Scrap Basin, Model S914
n Pot/Pan Scrap Basin, Model P914
Widely accepted in areas that restrict
the use of food waste disposers.
An Economical Pulper Alternative, the Collector
washes soluble food waste harmlessly through the sewer,
reducing bulk food waste by as much as 50% and weight
by as much as 80%.
Recirculated Water used for pre-flushing typically
reduces water and sewer costs dramatically. The
Collector consumes only 2 gallons of new water per
minute while the pre-flushing water plume recirculates at a
30-gallon rate.
Scrapping Speed is more than doubled compared to
an overhead pre-rinse since the worker’s hands are free
for scrapping. The Collector lets you keep up with small
to medium size conveyor dishmachines.
Problem Dishes, Trays and Cookware with dried
or baked-on food need much less hand work. They can be
soaked in the Collector basin while scrapping continues on
other dishes.
Job:
Model P914
Item No.:
HydroLogic Control Panel saves water and energy.
Includes patented operator sensing technology with two
water saving modes.
U.S. Pat. No. 7,815,134
TYPICAL INSTALLATIONS
Model S914
Model P914
Scrap Collector™ Model S914
Pot/Pan Scrap Collector™ Model P914
Model S914
Model P914
36 1/2"
(92.78)
24 13/16"
(63.09)
22 1/4"
(56.52)
22 1/4"
(56.52)
TABLE CUTOUT DETAIL
TABLE CUTOUT DETAIL
26 13/16"
(68.10)
38 1/2"
(97.79)
21 1/2"
(54.61)
33 3/16"
(84.30)
24 1/2"
(62.23)
24 1/2"
(62.23)
211/2"
(54.61)
211/2"
(54.61)
TOP VIEW
TOP VIEW
UTILITY
CONNECTION
• Incoming electrical connection ➔ factory wired control panel
• Incoming hot/cold water connection ➔ factory plumbed water harness
• Drain connection ➔ 2” NPT
ONE BASKET PROVIDED WITH UNIT
Additional basket recommended at additional cost
22" (55.88)
miniumum
clearance
overhead
for basket
removal
Scrap Basket dimensions
18 9/16" dia. x 131/4" high
(47.2) dia. x (33.7) high
Removable
Top
4 3/16"
(10.60)
14 7/8"
(37.78)
24"
(61.01)
Air Gap
15 7/8"
(40.33)
32 7/8" (83.50)
adjustable to
35 7/8" (91.12)
1/2” conduit
knockout
electrical
connection
Hot and cold
shutoff valves
1/2” NPT
UTILITY
CONNECTION
1 7/16"
(3.70)
UTILITY
CONNECTION
Tank drain
2” NPT
UTILITY
CONNECTION
4 9/16"
(11.62)
4 9/16"
(11.62)
Plume height
adjustment valve
LEFT SIDE VIEW
Model S914 shown - P914 similar
18 1/8"
(46.10)
15 3/8"
(39.05)
FRONT VIEW
NOTE: Dimensions in parenthesis are in centimeters
7 7/16" (18.82) to
10 7/16" (26.44)
Scrap Collector™ Model S914
Pot/Pan Scrap Collector™ Model P914
Dish Flow
Dish
Machine
Gusher Plate
24” min.
Dish rack space
The gusher plate should be situated on the
same side as the dish machine.
Leave a minimum of 24” between the
Collector and dish machine for a dish rack.
Upon request,
the Collector top
may be shipped
separately to
a fabricator for
welding to table.
ALL CONNECTIONS
ARE TO BE MADE BY
QUALIFIED PERSONNEL
WHO WILL OBSERVE
ALL LOCAL AND
NATIONAL CODES.
Model S914 shown - P914 similar
2” TANK DRAIN
(Piping not furnished)
The control and operator sensor can be mounted on either
side of the Collector using existing fasteners, mounting
holes and wiring to accommodate dish flow to the left or
dish flow to the right. It is not necessary to disconnect
factory-installed wiring.
The control and sensor should always face the operator.
If necessary, the control can be mounted remotely.
Additional field wiring and hardware will be necessary.
Contact service for installation advice.
Salvajor Scrap Collector
TM
MODEL S914 & Model P914
S
P
E
C
I
F
I
C
CONSTRUCTION
A
T
I
O
N
S
VOLTAGES AVAILABLE
n Tank - 2 Piece Stainless Steel
n Adjustable Legs - Stainless Steel
n Control Panel - Stainless Steel
n Salvage Basin - High Impact Polymer
n Scrap Basket - High Impact Polymer
ELECTRICAL
n Pre-wired NEMA 4 Control Panel
n Patented Operator Sensor
n Watertight Conduit/Fittings
n Separate Component Grounding
n Thermally Protected Motor
n Safety Line Disconnect
n 24 Volt Safety Circuitry
PLUMBING
n Corrosion Resistant Components
n Automatic Water Blender
n 24 Volt Solenoid Valves
n Unions
n Check Valves
n Incoming Water Valves
n Non-clogging Pump Design
n Pump Intake Screen
n Back Flow Prevention Device
ACCESSORIES
( SPECIFY EXACT OPERATING VOLTAGE )
115V
208V
230V, 60 Cycle, 1 Phase
208V
230V
460V, 60 Cycle, 3 Phase
Pump Motor 3/4 HP
FULL LOAD AMPS
( SPECIFY EXACT OPERATING VOLTAGE )
1 PHASE
3 PHASE
115V208V 230V208V230V460V
11
5.5
5.5
3.2
3
1.5
UTILITIES REQUIRED
1.Electric service
2.3/4” hot and cold water supply and
reduce to 1/2” at connection.
3.2” tank drain.
(Specifications subject to change without notice.)
SAMPLE SPECIFICATIONS
Unit shall be a Scrap Collector (or Pot/Pan Scrap
Collector) scrapping, pre-flushing and food waste
collecting system with recirculating water as
manufactured by Salvajor.
Model S914 (or P914), ____Volts, 60Hz, ___Phase.
Remote Start-Stop
Remote Mounting Bracket
Correctional Package
Control Mounting Bracket
Additional Scrap Basket
Furnished with a pre-wired HydroLogic control
panel, sensor and stainless steel NEMA 4
watertight enclosure.
U.S. Pat. No. 7,815,134
The Salvajor Company
1- 800 - SALVAJOR
www.salvajor.com
4530 East 75th Terrace Kansas City, Missouri 64132-2081, USA
(816) 363 - 1030
FAX: 1 - 800 - 832 - 9373
Email: [email protected]
[email protected]
Manufacturers of Commercial Food Waste Solutions since 1944
Printed in USA
Form No.S&P914 (08-16)