MedStat
MS 100 SPECIFICATIONS
CHASSIS AND CAB STANDARD FEATURES
Chassis
Polaris RANGER 6x6
Color – Standard Polaris Solar Red Hood and Dash
Engine
Engine Type
Displacement
Lubrication
Cooling System
Starting
Exhaust
Twin Cylinder, 4-Stroke
760 cc,HO
Pressurized Wet Sump
Liquid - cooled
Electric
Canister Style
Fuel
Fuel System
Fuel Tank
Fuel Delivery
Fuel Type
EFI
9.0/34.1 gal/ltr
Electronic Fuel Pump
Gasoline – 87 Octane or 89 Oxygenated
Electrical
Alternator
Battery
Headlight
Brake Light/Taillight
DC Outlet
500 Watts
Electric / 12 volt – 30 amp hour
50 w quartz-halogen
Standard/Standard
Dash Receptacle
Drivetrain
Transmission
Drive System
Final Drive
Automatic - PVT (Polaris Variable Transmission) High, Low, Neutral. Reverse
On-Demand True 6 WD/Rear 4WD/Mid Differential Lock
Shaft
Steering
Power Steering
Polaris Model Electronically Controlled Power Steering System
1
Revised 9/21/11
MedStat
MS 100 SPECIFICATIONS
Suspension
Front Suspension
Rear Suspension
Dual A-Arm w/ 9.6 in./ 24.4 cm of travel
4-Wheel Dual A-Arm, IRS 9 in./22.9 cm of travel
Brakes & Tires
Brakes - Front/Rear
Parking Brake
Front Tire Size
Rear Tire Size
Hydraulic Disc with Dual - Bore Front Calipers
Hand – Actuated, Dash Mounted Lever
25 x 10 x 12 Off-Road Tires on Painted Steel Rims
25 x 11 x 12 Off- Road Tires on Painted Steel Rims
Dimensions & Capacities
Wheelbase
Length/Width/Height
Ground Clearance
Dry Vehicle Weight
Gross Vehicle Weight
Top Speed
Hitch Towing Capacity
Approx 110”
180/63/93 in.
10 in.
2250 Lbs
4,500 Lbs
40 MPH/64 KPH
2000 lbs.
Hood, Dash
The hood and dash shall be the standard Polaris Solar Red. The hood and dash shall be made from high-density
polyethylene (HDPE).
Roof and Roll Bar
The unit shall have the Polaris factory installed ROPS Certified roll bar. Attached to the roll bar will be an 11
gauge aluminum tread plate roof panel. The roof panel is to provide protection to the driver and passenger.
Mirrors- Left, Right, and Rear View
One convex mirror head measuring 5”x7” is to be mounted on each side of the unit. The mirror arms shall have a
built in break-away feature allowing them to pivot inward for tight locations. A 4”x6” center mounted rear view
mirror shall also be supplied allowing the driver to see in the patient module.
Skirting- ABS
The side skirting made from .375 thick ABS material shall be supplied around the bottom of the module. This
skirting shall give the unit a smoothed and finished appearance around the frame and rear tires.
2
Revised 9/21/11
MedStat
MS 100 SPECIFICATIONS
Step- Rear
A 40” x 10” aluminum tread plate step shall be provided at the rear of the unit. The step is to aid in the entering
and exiting of the rear module.
REAR (PATIENT) MODULE STANDARD FEATURES
All Aluminum Construction
The rear module shall be constructed of Aluminum tread plate flooring (No less than .125 thick), side walls and
roof, (No less than .090 thick). The floor sub structure shall consist of aluminum tubing. The frame structure for
walls and roof shall be made using an aluminum extrusion with a 3 in. radius corner with grooves for the side
walls to mount inside.
Rear module side windows shall be deep tinted sliding w/screens RV style.
Floor to Ceiling Height
Interior Width
Interior Length
No less than 55" and not to exceed 58”
No less than 58" and not to exceed 60”
No less than 90" and not to exceed 96”
The purpose of the design of the module is to allow the ability to carry one (1) patient (customer specified
stretcher) and one (1) attendant from the immediate accident scene to a pre-determined shelter and/or additional
transport device (i.e. standard ambulance) in a safe and stable manner.
Painted Interior- Zolatone Finish
The Interior Ceiling, Front and Sides shall be painted with Zolatone finish (Light Gray).
Painted Exterior- White Standard
All rear module seams shall be caulked both inside and along the exterior edges with an automotive sealant to
prevent moisture from entering between any body panels.
The rear module, module doors if applicable, and all parts shall be thoroughly sanded, and washed with solvent.
Tacked free of any dust particles, the body and all applicable parts shall be individually sprayed using the
following minimum procedure and materials:
Two (2) coat of epoxy primer
Two (2) coats of the specified color
Two (2) coats of clear urethane
3
Revised 9/21/11
MedStat
MS 100 SPECIFICATIONS
Bench Seat- 60” with Seat Belt, Seat Pad, and Built in Storage
A 60” wide bench seat shall be provided in the rear module. The bench will have two Durawear® covered seat
pad and two 48” retractable seat belts for one occupant. The two seat pads will lift up giving access for storage
inside the bench.
Cot Mounting System
A Stryker Cot mounting system shall be provided in the rear module. This system will accommodate a standard
full size cot.
Door- Side Access to Bench Storage
A bottom hinged door approximately 48” wide and 13 3/4” high located on passenger side of the rear module to
provide exterior access to the under bench storage shall be provided. The door shall be a flush mount design
and will have two (2) push button paddle style latches located in the top area of the door. When open, the door
shall have ample support to provide a work shelf area as well.
Door- Rear Canvas
The rear door area shall have a canvas roll up door with dual side zippers. The door shall be made from
polyester marine canvas material with a single window in the center made from aqua-view vinyl.
Grab Handles- Interior (1) Entry Door and (1) Ceiling
One (1) grab handle shall be mounted in the center of the ceiling, and one (1) mounted near the rear door
opening.
One (1) 30” exterior aluminum grab handles shall be mounted on the left and right of rear module.
Windows
There shall three (3) 12” x 40” sliding auto safety glass windows, one in each side, and one in the front of the
rear module. They shall have insect screen and dark tinted glass to aid in privacy and to keep the inside cool.
LIGHTING STANDARD FEATURES
Headlights
4
Revised 9/21/11
MedStat
MS 100 SPECIFICATIONS
There shall be dual 50 quartz- halogen lamps mounted in the front grill.
Fluorescent Dome Light –One (1) in Cab, Two (2) in Rear Module
There shall be three (3) 14” fluorescent light fixtures with on/off switch one (1) in cab, two (2) in rear module. The
light will have dual fluorescent 14” tubes with a clear plastic cover protecting the bulbs.
Tail Lights
Two red taillight bulbs shall be provided and mounted in the tail panel. The lights will illuminate when the
ignition key is in the “on” position.
TIRES AND WHEELS STANDARD FEATURES
Carlisle Off-Road Tires
There shall be six (6) Carlisle Off-Road tires provided. Two (2) 25x10x12 front and four (4) 25x11x12 tires
will be provided.
Steel Wheels- Black
There shall be six steel wheels painted black. Two (2) front (25x7x12), four (4) rear (25x8x12) wheels.
CUSTOMER REQUESTED OPTIONS
5
Revised 9/21/11