Company Profile – BeadMet (Pty) Ltd 2017
Quality Control, Inspection & Welding Engineers
Ref: BM-CPR-0001 Rev 9- 22/08/2016
BEADMET
Reg. No.: 2012/084174/07
VAT: 4810266280
Company Profile
And
Services
Directors: Simbarashe P. Govo (Managing Director) - IIW-ZA/IWE; Farirai D. Govo
Company Profile – BeadMet (Pty) Ltd 2017
Quality Control, Inspection & Welding Engineers
Ref: BM-CPR-0001 Rev 9- 22/08/2016
1.0
Introduction
BeadMet (Pty) Ltd – is a 100% black emerging private owned company with a B-BBEE level 4 verified status. The company was
established in 2012 to provide Welding Engineering Services. Our services include Consultancy, Non Destructive Testing, Fabrication &
Installation Support, Quality Control, Welding Administration, Inspection & Repair Coordination, Strategic Sourcing, Surface Painting &
Coating Inspection, and Training services. Our target market being the power generation, petrochemical, manufacturing and authorized
inspection houses, mining, metallurgical, rail, and related industries.
We oversee all quality control and welding related documentation on behalf of our clients during plant shutdown, maintenance, turnkey
projects and shop or site equipment manufacture, repair or modification. BeadMet has capability to source and supply to client orders
all welding related equipment and consumables during execution of welding and fabrication work. We assist our clients in the
qualification of welding procedures and personnel to meet code manufacturing requirements and compile all associated documentation.
Our experience in the application of ISO 3834-2 welding quality standard and involvement in supplier accreditations gives us the edge in
setting up such welding quality systems. Our approach will involve audits of client’s current welding practice with recommendations for
improvement. This is then followed by detailing procedures that control input resources to the final product output.
BeadMet (Pty) Ltd offers a range of short courses tailor made to our client needs. These courses include but not limited to quality
control, inspection, welding engineering and code specific fabrication.
As part of management consulting we offer reliability services. Our reliability department is supported by key expert partners in risk
based inspection and component life assessment. Through our strategic sourcing we are geared to assist clients in sourcing the right key
personnel during site projects, plant maintenance and plant shut down.
We have established quality, Safety, Health and Environment systems and procedures that are in line with ISO 9001: 2008 and ISO
14001/ OHSAS 18001. Our objectives and policies are thus aligned with these systems.
Directors: Simbarashe P. Govo (Managing Director) - IIW-ZA/IWE; Farirai D. Govo
Company Profile – BeadMet (Pty) Ltd 2017
Quality Control, Inspection & Welding Engineers
Ref: BM-CPR-0001 Rev 9- 22/08/2016
2.0
Company Divisional Structure
BEADMET (PTY) LTD
Construction
[See Separate Profile]
2.1
Engineering Supplies
[See Separate Profile]
Quality Control,
Inspection &
Welding Engineering
Logistics
[See Separate
Profile]
Electrical &
Instrumentation
[See Separate Profile]
Services offered – Quality Control, Inspection & Welding Engineering Division
QUALITY CONTROL, INSPECTION & WELDING ENGINEERS DIVISION
TECHNICAL SERVICES
Welding Engineering
Reliability Engineering
Risk Based Inspection*
Component Life
Assessment*
Training
INSPECTION &
QUALITY MANAGEMENT
Non-Destructive Testing
Conventional Inspection
Services
VT; PT; MT; UT; Hv; PMI; Wall
THK; Endoscopy; Replication;
Advanced Inspection Services
ToFD; PA; GWT;
EMAT Boiler Tube THK Mapping
Painting & Coating Inspection
Quality Control
Directors: Simbarashe P. Govo (Managing Director) - IIW-ZA/IWE; Farirai D. Govo
SOURCING MANAGEMENT
Strategic Sourcing
Payroll & Contractor
Management Services
Company Profile – BeadMet (Pty) Ltd 2017
Quality Control, Inspection & Welding Engineers
Ref: BM-CPR-0001 Rev 9- 22/08/2016
3.0
Mission Statement
We provide quality control, inspection and welding engineering solutions within South Africa and beyond borders while exceeding
customer expectation at competitive cost.
4.0
Vision
To become the most valued service partner by going an extra mile to provide solutions to clients within all our service offers.
5.0
Values




Customer satisfaction
Innovation
Integrity
Efficiency
Directors: Simbarashe P. Govo (Managing Director) - IIW-ZA/IWE; Farirai D. Govo
Company Profile – BeadMet (Pty) Ltd 2017
Quality Control, Inspection & Welding Engineers
Ref: BM-CPR-0001 Rev 9- 22/08/2016
6.0
BeadMet Quality Policy Statement
BeadMet (Pty) Ltd is committed to surpassing customer satisfaction through innovative and efficient service delivery. The company
embraces cost effective and high quality standard in all executed work. BeadMet (Pty) Ltd further commit to foster a systematic
business approach to ensure consistency in meeting client needs. We monitor our service and aim for continuous improvement in all
our key deliverables.
BeadMet (Pty) Ltd shall ensure:









That all the activities which affect the Quality of our products/services are under control, whether hardware, software, materials
or services.
That the Quality management control function has been orientated towards the reduction, elimination and, most importantly,
prevention of Quality non-conformities, as well as ensuring customer satisfaction and continual improvement.
Efficiency and profitability.
Continuous conformance to environmental standards.
Timeous identification of potential deviations.
Improved communications and morale in BeadMet (Pty) Ltd and to have a good relationship with our customers and
stakeholders.
Care of employees, their welfare, training and safety.
That all necessary corrective and preventive actions are taken when deviations occur.
Optimum utilization of resources.
In reaching all the above-mentioned objectives BeadMet (Pty) Ltd shall utilize and conform to the requirements of SABS / ISO
9001:2008 in relationship with ISO 9004:2000 Quality Management System. All our welding related services and products are
established upon the principles of ISO 3834-2 comprehensive requirements.
Directors: Simbarashe P. Govo (Managing Director) - IIW-ZA/IWE; Farirai D. Govo
Company Profile – BeadMet (Pty) Ltd 2017
Quality Control, Inspection & Welding Engineers
Ref: BM-CPR-0001 Rev 9- 22/08/2016
7.0
BeadMet Health, Safety & Environmental Policy
BeadMet (Pvt) (Ltd) has an on-going commitment and vision to be a recognised world leader in the provision of all its service offers. In
line with this vision, we aim to provide our services in a way that adds value to our clients’ businesses and achieve a higher level of
client satisfaction.
And therefore commits to:
1. Implement and maintain ethical business practices and sound corporate governance processes.
2. Eliminate or prevent personal injury and occupational health hazards & diseases associated with client environments.
3. Eliminate, prevent or mitigate our impact on the environment through optimization of resource consumption, protection of
environmental biodiversity, minimization of release of effluent and emissions &, waste minimization.
4. Comply with all applicable Occupational Health, Safety and Environmental legal requirements, as determined by industry
requirements.
5. Ensure customer satisfaction by understanding our customer requirements, strive to exceed customer expectations, and providing
consistent high quality product and service.
6. Set the framework for setting safety, health, environmental and quality objectives at relevant functions in the organization.
7. Operate appropriate systems to provide training to employees and contractors to ensure that they are competent to carry out
duties and responsibilities towards achieving the objectives of this policy.
8. Continually improve our SHE program through risk assessments, analysis of data, audits, inspections, process monitoring, product
monitoring, customer feedback, incident investigations, policy and management reviews.
9. Review this policy and SHE system performance periodically and/or when they are changes affecting its suitability and relevance.
10. Communicate this policy to all employees working for and on behalf of BeadMet. This policy will be displayed at conspicuous places
and will be made available to all visitors, stakeholders, and interested and affected parties.
Directors: Simbarashe P. Govo (Managing Director) - IIW-ZA/IWE; Farirai D. Govo
Company Profile – BeadMet (Pty) Ltd 2017
Quality Control, Inspection & Welding Engineers
Ref: BM-CPR-0001 Rev 9- 22/08/2016
8.0
TECHNICAL SERVICES
8.1
Welding Engineering Technical Services












8.2
Assist manufacturers in the development, management, approval and issue of qualified welding procedure specifications (WPS's)
to client/ manufacturing code requirements. Such codes include but not limited to ASME IX, AWS D1.1, EN 15614-1 & API 1104
Provide recommendations on repair welding of structural, piping, boiler and pressure vessel equipment.
International Welding Engineer (IWE) services.
Welding related support during product design, this includes assistance in material selection.
Failure investigation on welded equipment/ structures.
Welding related training, this includes QC level I and level II related courses, metallurgical & welding engineering courses,
manufacturing codes & standards, etc.
Provide recommendations for a sound welding practice.
Assist clients/ manufacturers in welding personnel qualification and documentation of welding performance qualification
certificates.
Compilation and issue of job specific prequalified and preliminary welding procedure specifications (preWPS).
Advisory support towards implementation of a welding related quality system, e.g. ISO 3834-2.
Coordinate weld refurbishments of capital equipment.
Technical support during heat treatment of fabricated components.
Reliability Engineering
8.2.1 Risk Based Inspection
BeadMet through its partners offers technical support in planning of Risk Based Inspection (RBI) on capital equipment. This involves a
careful assessment of various damage mechanisms related to equipment service life and ranking failure probability and consequence.
This process is then used to build inspection intervals which can lead to less equipment downtime and longer service life. We follow
various widely accepted international engineering guidelines on RBI such as API 580; API 581; ASME PCC – 3; etc. Equipment of RBI
relevance include but not limited to power generation equipment; storage tanks; steam turbines and equipment of high temperature
service.
Directors: Simbarashe P. Govo (Managing Director) - IIW-ZA/IWE; Farirai D. Govo
Company Profile – BeadMet (Pty) Ltd 2017
Quality Control, Inspection & Welding Engineers
Ref: BM-CPR-0001 Rev 9- 22/08/2016
8.2.2 Component Life Assessment
Boiler headers, tubes and pipework are designed for a finite life based on strength, stress rupture, fatigue and creep rate design limits.
Even in the absence of an accelerating damage mechanism, components operating at high temperature are likely to fail due to long-term
overheating or creep. Interval inspections of these components are important to predict the remaining life of these components and
these inspections are critical in preventing failures. Evaluation of remnant life-time of high thermal components also gives possibilities
for optimisation of plant maintenance and revitalization. Life time in service of particular components is highly dependent on material
of fabrication. BeadMet provides plant life assessment by adopting destructive and non-destructive testing methods, at the same time
ensuring adherence to relevant technical standards.
8.3
Training
We offer a range of short courses for the welding and inspection personnel (engineers, QA/QC inspectors, inspectors of pressurized
equipment - IPE’s, competent persons – pressure vessels & steam generators, welding specialist, welders, etc.) that can be tailor made
to suit client needs.
These courses include but not limited to quality control, inspection (QA/QC), welding engineering and code specific fabrication.
9.0
INSPECTION & QUALITY MANAGEMENT
9.1
Non-Destructive Testing (NDT)
9.1.1 Conventional Inspection Services
We offer the following conventional non-destructive testing techniques:
 Visual Examination/ Testing (VT)
Our visual examination include but not limited to dirty boiler inspections, in-service component inspections, document review, inspections
before, during and after welding, reporting and sign off.
 Magnetic Particle Testing (MT
 Liquid Penetrant Testing (PT)
Directors: Simbarashe P. Govo (Managing Director) - IIW-ZA/IWE; Farirai D. Govo
Company Profile – BeadMet (Pty) Ltd 2017
Quality Control, Inspection & Welding Engineers
Ref: BM-CPR-0001 Rev 9- 22/08/2016






Ultrasonic Testing (UT)
Hardness Testing (HV)
Positive Material Identification (PMI)
Wall Thickness Examination
Endoscopy
Replication
9.1.2 Advanced Inspection Services
In addition to conventional methods of inspection, BeadMet can offer advanced inspection techniques to its clients. These are basically
employed to further identify and characterize indications and best provide more information of damage mechanisms. They can also be
employed on members that are not accessible. Following is a list of advanced techniques that BeadMet can provide:
9.1.2.1
Time of Flight Diffraction (ToFD)
TOFD has extremely accurate defect sizing capabilities using diffraction of the ultrasonic wave when it encounters indications such as
for example, cracks. Two probes are used, one is the transmitter of the ultrasonic wave and the other is the receiver. These probes are
mounted on a buggy to pick up, record and size indications as the buggy is moved along the area under examination.
9.1.2.2
Phased Array (PA)
Phased Array can be employed as a stand-alone technique or in conjunction with TOFD. The technique offers capabilities of inspection of
complex geometries or components with limited access.
9.1.2.3
Guided Wave Testing (GWT)
Inaccessible piping can be inspected using the Guided Wave Inspection Technique. Guided Wave Inspection offers the following
advantages:

Minimal removal of insulation in cases where inspections of corrosion under insulation.
Directors: Simbarashe P. Govo (Managing Director) - IIW-ZA/IWE; Farirai D. Govo
Company Profile – BeadMet (Pty) Ltd 2017
Quality Control, Inspection & Welding Engineers
Ref: BM-CPR-0001 Rev 9- 22/08/2016






Large areas can be inspected rapidly.
Internal and external wall loss.
Possibility of long range piping inspections.
Less requirement for scaffolding when inspecting components in elevated heights.
Highly productive inspection technique.
Hundreds of meters of pipelines can be inspected from a single location.
9.1.2.4
In Service EMAT Boiler Tube Thickness Mapping
We are geared to offer this service using temate® TG-IS (B) which is a redesigned FST-GAGE or Fast Scanning Thickness Gage, first introduced in
1994. FST-GAGE was developed by Electric Power Research Institute (EPRI) and Babcock & Wilcox (B&W) specifically to scan boiler tubes and
provide a continuous measurement of tube wall thickness.
The system works on ultrasonic EMAT (Electro Magnetic Acoustic Transducer) technique providing accurate thickness (with accuracy of +/0.127mm) readings with none or minimal tube surface preparation. The probe with integrated encoder and light indicators (for fast visual alert to
the operator) is manually scanned along the boiler tube while the system records the thickness & alarms if the tube is below a pre-programmed
threshold or other defect conditions are triggered. The system saves a complete record of each tube & the whole boiler for later post analysis &
tracking.
Apart from detecting wall loss the system is capable of detecting hydrogen damage, pitting & caustic gouging (by measuring signal attenuation)
which is not detected with conventional means. It works on carbon steel and clad tubes. Tube thickness ranges from 3.8mm to 12.7mm & the
minimum tube diameter requirement is 22.2mm, the tube surface can be oxidized, rough or pitted (scale-free).
The technique permits 100% inspection of the boiler instead of spot checking at up to 15cm/s of scanning speed. The boiler mapping tool permits
easy visualization of boiler walls with results of inspection for fast analysis and interpretation.
9.3
Painting & Coating Inspection
BeadMet offers corrosion engineering and surface coating solutions with the sole aim of enhancing life on capital assets. Our team of
experts are experienced and willing to assist in identifying unique corrosion and coating technologies that are within project
requirement and economically viable.
We are able to provide on-site independent quality control inspectors to ensure proper adherence to painting and coating specification
and project-specific requirements. Our services include but not limited to:
Directors: Simbarashe P. Govo (Managing Director) - IIW-ZA/IWE; Farirai D. Govo
Company Profile – BeadMet (Pty) Ltd 2017
Quality Control, Inspection & Welding Engineers
Ref: BM-CPR-0001 Rev 9- 22/08/2016









9.4
Independent painting and coating inspection during projects, planned and forced maintenance.
Wet and Dry Film Thickness Measurements
Holiday and Pinhole Detection
Surface Profile and Cleanness Measurements
Adhesion Tests
Repair and recoating of damaged areas.
Protective coating condition assessment.
Failure analysis.
Placement of qualified painting and coating inspectors.
Quality Control




Make provision for interface between client QA/QC inspectors to work hand in hand with BeadMet (Pty) Ltd QA/QC/NDE
inspectors for enhanced quality control during site projects, planned and forced maintenance.
Representation during welding related projects. This includes review of welding documents, quality plans, inspection and test
plans, resolving concession and NCR issues; independent auditing of potential manufacturer’s welding quality system before
project commencement, etc.
Assist in document control & review of fabrication data books on behalf of the client.
Coordinate the provision of personnel to conduct various non-destructive examination (NDE) before, during and after welding.
10.0 SOURCING MANAGEMENT
10.1 Strategic Sourcing
BeadMet (Pty) Ltd is geared to assist clients in sourcing the right key personnel during site projects, plant maintenance and shut down
services. Our experience and close industrial interactions gives us the edge in head hunting for the right key personnel.
We have capability to source and supply welding related consumables to client orders. Every effort is sought to meet delivery target
dates and maintain continuous improvement after each consignment delivery. Our experience in capital assets forms the foundation of
Directors: Simbarashe P. Govo (Managing Director) - IIW-ZA/IWE; Farirai D. Govo
Company Profile – BeadMet (Pty) Ltd 2017
Quality Control, Inspection & Welding Engineers
Ref: BM-CPR-0001 Rev 9- 22/08/2016
our technical support in procuring the right equipment for each unique need. Our industrial supplier links and partnerships serve as our
basis for technical assistants in product procurement to meet client needs.
10.2 Payroll & Contractor Management
We support contracting and consulting entities with payroll and contractor management services. This will allow our clients to focus on
their core scope of work and leave us to carry all tax and statutory labour obligations of temporary manpower.
Directors: Simbarashe P. Govo (Managing Director) - IIW-ZA/IWE; Farirai D. Govo
Company Profile – BeadMet (Pty) Ltd 2017
Quality Control, Inspection & Welding Engineers
Ref: BM-CPR-0001 Rev 9- 22/08/2016
11.0 Management, Qualifications & Responsibility
Mr. Simbarashe Govo
[Managing Director]
Bsc. Hons Eng.; Msc (Eng); M. Eng; IIW-ZA/IWE 00035; NACE Coating Inspector Level 1 – Certified; Ass Member – SAIMM
Mr SP Govo is a registered international welding engineer (IIW/ IWE) who holds a Bsc Honours degree in metallurgical engineering
from the University of Zimbabwe, Master of Science in engineering & Master in Engineering (welding) all from the University of the
Witwatersrand and an international welding engineer diploma. He has exposure and experience to renowned welding training
institutes, heavy engineering and petrochemical firms within the republic of South Africa. He is mainly responsible for the business
plans, providing leadership and direction aimed at enhancing the organization as a whole.
Mr SP Govo has been involved with the following companies within Zimbabwe and South Africa. His immense contributions in welding
engineering and fabrication projects in the various positions held cannot be over emphasized.
Summary of work experience to date – S.P. Govo
Employer
Capacity/ nature of work
BeadMet (Pty) Ltd
Managing Director
SASOL Synfuels - Secunda
Welding Engineer [IIW-ZA/IWE]
DCD Heavy Engineering – Mining &
Welding Engineer
Energy
Southern African Institute of Welding
Lecturer/Consultant
(SAIW)
University of the Witwatersrand
M.sc (Eng.) research student & tutor for 1st year
process engineering
Ziscosteel (Zimbabwe)
Plant Metallurgist
Ziscosteel & Steelmakers (Zimbabwe)
Graduate Metallurgist
Directors: Simbarashe P. Govo (Managing Director) - IIW-ZA/IWE; Farirai D. Govo
Period
June 2012 - Present
Aug 2012 – Nov 2014
Jan 2011 – July 2012
March 2010 – Dec 2010
July 2007 – Feb 2010
Sept 2006 – June 2007
Feb 2005 – Aug 2006
Company Profile – BeadMet (Pty) Ltd 2017
Quality Control, Inspection & Welding Engineers
Ref: BM-CPR-0001 Rev 9- 22/08/2016
Mrs. Farirai Govo
[General Manager]
Hons. SW; MA Soc. Dev.; SACSSP – Social Worker [10-27867]
Mrs FD Govo holds an Honours Bachelor’s degree in Social Work from the University of Zimbabwe and a Master in Social Development
Studies from the University of the Witwatersrand. She is registered with the South African Council for Social Service Professions
(SACSSP) as a Social Worker and has worked in various non-governmental organizations in the republic of South Africa. She brings into
the organization diversity around all human resource aspects of the organisation that are aimed at continuous development of the
company as a whole. She heads and coordinates all training activities, recruitment; Accounts and general administration of the business.
Mr. Orifuna Netshifamadi
[Technical Manager]
PR. Eng., IIW-ZA/IWE
A professional metallurgical engineer (ECSA) with expert knowledge in industrial boiler life assessment. Previously employed at Eskom
Sustainability Division as a Senior Metallurgical & Welding Engineer (Oct 2009 – Mar 2015). His responsibilities were welding
engineering & welding quality assurance, component inspection, component life assessments, and failure investigations on power plant
materials. Power plant materials include boiler tubes & boiler structural members, high temperature & high pressure main steam
pipework, pressure vessels, steam turbine rotors & casings, and boiler auxiliary plant components.
He was employed at Volkswagen South Africa as a Senior Welding Engineer (2007 – 2009). His responsibilities were to oversee
procedure and performance qualification according to EN 15614 & EN 287, Non-Destructive Testing during automotive body in white
construction, optimization of welding processes, and periodic destructive testing of automotive body in white.
Prior to VW RSA he was employed at the CSIR under the Material and Manufacturing Division as an assistant metallurgist (2003 – 2004).
His responsibilities were to carry out failure investigations of industrial components.
Mr Netshifamadi holds a BSc (Eng.) Metallurgy (2005) and a Master of Engineering (Materials and Metallurgy) with special focus on
welding engineering from the University of the Witwatersrand (2013). A certified International Welding Engineer (IWE) from SAIW and
IIW (2014). He has also completed welding inspection level 1 and level 2 from the SAIW (2008).
Directors: Simbarashe P. Govo (Managing Director) - IIW-ZA/IWE; Farirai D. Govo
Company Profile – BeadMet (Pty) Ltd 2017
Quality Control, Inspection & Welding Engineers
Ref: BM-CPR-0001 Rev 9- 22/08/2016
12.0 References
Client
LILITHA ENGINEERING SOLUTIONS (PTY) LTD
Contact Name:
Ndumiso M. Tyibilika
[Managing Director]
Tel:
+27 11 450 3594
Mobile:
+27 82 415 9929
Services
Joint Venture Partner – Eskom Matla Power Station
-Welding Administration & Inspection Coordination During Boiler
Tube Leaks and Planned Maintenance (Unit 1 to 6)
-Boiler Maintenance Repair Coordination (Unit 1 to 6)
AVENG GRINAKER LTA – M & E Construction
Contact Name:
David Melato
[Divisional Quality Assurance Manager]
Tel:
+27 11 923 5000
Mobile:
+27 71 684 9758
-Technical Welding Engineering Services on as required basis:
-Welding Engineering Services At Medupi Power Station.
-Inspection and Quality Control (Medupi Power Station) – Supply of
QC Inspectors.
ESKOM Matla Power Station
Contact Name:
Lele Masote
[Engineering Manager]
Tel:
+27 17 612 9000
Mobile:
+27 72 780 6205
SVK Holdings
Contact Name:
Joe Pretorius
[General Manager : Energy & Construction]
Tel:
+27 (0) 86 143 6263
Mobile:
+27 (0) 82 904 4563
COENG Consulting & Construction Engineers (Pty) Ltd
Contact Name:
Mr. Casian Dendere
[Chief Executive Officer]
Tel:
+27 11 312 5213
Mobile:
+27 71 676 2490
-Welding Administration and Inspection Coordination During Boiler
Tube Leaks and Planned Maintenance (Unit 1 to 6).
-Welding Engineering Technical Support
-Boiler Maintenance Repair Coordination (Unit 1 to 6)
Directors: Simbarashe P. Govo (Managing Director) - IIW-ZA/IWE; Farirai D. Govo
-Review of welding procedures and advisory
-Assist in compilation of PQR’s and WPS’s to EN 15614-1 & ASME IX
for use in the construction of the Medupi Power Station.
-Sourcing of Project QC Inspectors
-Technical Welding Engineering Services on as and when required
basis.
Company Profile – BeadMet (Pty) Ltd 2017
Quality Control, Inspection & Welding Engineers
Ref: BM-CPR-0001 Rev 9- 22/08/2016
Raysonics
Contact Name:
Karen Van Wyk
[Admin/Inspection Manager]
Tel:
+27 17 610 3359
Mobile:
+27 82 601 6162
Harambee General Services, cc
Contact Name:
Mr Thabiso E. Mabogoane
[Managing Member]
Tel :
+27 13 656 2759
Mobile:
+27 (0) 82 503 6704
E-mail:
[email protected]
QUENCH GROUP
Contact Name:
Sello Tlake
[Operations Manager]
Tel:
+27 11 609 2765
Fax:
+27 11 609 2765; 086 567 9944
Mobile:
+27 81 364 6647
E-mail:
[email protected]
Directors: Simbarashe P. Govo (Managing Director) - IIW-ZA/IWE; Farirai D. Govo
-QC Level I Training/ Tutorials – For SAIW Inspectors Level I
examination re-writes.
-Welding Engineering Services for Eskom Tender Bid for
Maintenance of Duvha Power Station Units 1 to 6 Boiler House
-Compilation of Preliminary WPS’s to EN 15614-1
-Compilation of Preliminary WPS’s to EN 15614-1
-Site (Hendrina Power Station) advice and support
-Qualification of Welding Procedure Specification
Company Profile – BeadMet (Pty) Ltd 2017
Quality Control, Inspection & Welding Engineers
Ref: BM-CPR-0001 Rev 9- 22/08/2016
BeadMet (Pty) Ltd Organogram
Simbarashe Piniel Govo
[BSc Hon. Eng. (Met); MSc. Eng.; M. Eng.; IIW-ZA/ IWE]
[Managing Director]
Nkululeko Khumalo
Valencia Maziya
[Office Administrator]
Based at Matla Power Station
[Legal Advisor]
Patrick Mokaleng
[N. Dip; B. Tech
Metallurgy; M. Eng.]
[Technical Manager]
Farirai D. Govo
[Hons. SW; MA Soc. Dev.]
[General Manager]
Vacant
[HR Officer]
Raphael Mazula
[B. Acc.; SAIBA; MIRMSA; Reg. Tax
Practitioner]
[Finance Manager]
Ina Mbiza
[Pr. Tech Eng.]
[Business
Development
Manager]
Asante Mwasiswebwe
[BSc Hon. Eng. (Met); M. Eng.
[Welding Engineer]
QA/QC/NDE Inspectors
Collen Mahlangu –
Abel Ngomane –
Thabo A. Tshabalala –
SAIW Level II – Matla PS
MT, PT, UT, RT – Matla PS
SAIW II – Matla PS
** BeadMet has a LARGE Database of QC Inspectors to
Suit Any Scale of Project/ Maintenance Work **
Directors: Simbarashe P. Govo (Managing Director) - IIW-ZA/IWE; Farirai D. Govo
Babra Mudzanapabwe
Safety, Health, Environment
[Consultant]
Vincent Tshepo Damane
[Safety Officer]
Doreen Gwanyuki
[Quality Manager]
(QMS & Appointed
Management
Representative)
Company Profile – BeadMet (Pty) Ltd 2017
Quality Control, Inspection & Welding Engineers
Ref: BM-CPR-0001 Rev 9- 22/08/2016
13.0 Company Registration Details
Registered Name:
BeadMet (Pty) Ltd
Trading Name:
BeadMet (Pty) Ltd
Company Registration Number:
2012/ 084174/07
V.A.T
4810266280
Registered Physical Address:
32 River Drive Mews
Postal Address:
1 The Circus Street
Three Rivers Proper
Vereeniging
Gauteng
1939
Republic of South Africa
Bus:
Mobile:
Email:
Website:
32 River Drive Mews
1 The Circus Street
Three Rivers Proper
Vereeniging
Gauteng
1935
Republic of South Africa
+27 16 454 0418
+27 78 865 0830
[email protected]
www.beadmet.co.za
14.0 Management Contact Details
Simbarashe Govo
[Managing Director - IWE]
Bus:
+27 16 454 0418
Mobile:
+27 78 865 0830
Email:
[email protected]
Website:
www.beadmet.co.za
Directors: Simbarashe P. Govo (Managing Director) - IIW-ZA/IWE; Farirai D. Govo
Farirai Govo
[General Manager]
Bus:
+27 16 454 0418
Mobile:
+27 78 865 0830
Email:
[email protected]
Website:
www.beadmet.co.za
Company Profile – BeadMet (Pty) Ltd 2017
Quality Control, Inspection & Welding Engineers
Clients
Directors: Simbarashe P. Govo (Managing Director) - IIW-ZA/IWE; Farirai D. Govo
Ref: BM-CPR-0001 Rev 9- 22/08/2016