MS380 Wireless Scanner
Quick Reference Guide
LED Indication
General Setting
Off -- Ready for scanning or no
power
Blue -- Good reading
BlueRed -- Disconnection
Default
Beeper
Long Beep -- Power ON
Short Beep -- Good read
2 Beeps -- Connection or successful
setup
3 Beeps -- Disconnection or error
Check Version
Quick Connection
Step 1 - Connect the cradle to the host computer.
Device Manager will show “USB Human Interface Device”, and if you
double click it, it will show “Wireless Base” on its properties window.
Step 2 - Activate the scanner
Step 3 - Wait for connection
Press and hold the trigger for
1 second until a beep sounds.
The blue LED indicator on the cradle will turn on to
verify a successful connection to the scanner.
Caution: If the cradle fails to connect the scanner,
please follow the instruction of WIRELESS
CONNECTION OPTIONS section.
Unitech electronics co., ltd.
5F., No.135, Ln. 235, Baoqiao Rd., Xindian Dist., New Taipei City 231, Taiwan (R.O.C.)
y Tel: + 886 2 89121122 y Fax: +886 2 89121810 y website: www.ute.com
MS380 Wireless Scanner
Quick Reference Guide
Wireless Connection Options
Wireless Mode – HID Plug and Play (Default)
Wireless Mode – SPP
Step 1: Connect the cradle to the host PC.
If the host does not support Wireless
communication, a third-party Wireless
adaptor is required.
Step 2: Scan the [DISCONNECT] barcode.
Disconnect
Pincode List
(0)
Step 1: Scan the [DISCONNECT] barcode.
Disconnect
(1)
Step 3: Scan the [Wireless mode - HID plug & play]
barcode, and the scanner will emit 8 beeps.
Wireless mode - HID plug & play
Step 2: Scan the [Wireless mode - SPP]
barcode, and the scanner will emit 8
beeps.
(2)
Wireless mode - SPP
(3)
Step 4: Scan the Host Address barcode on the
cradle’s
bottom.
Step 6: The scanner will beep twice and cradle’s blue
indicator LED will stay on to verify a
successful connection.
Step 3: Select “Wireless Scanner” from the
discovered device list. The default
pincode is “1234”.
Wireless Mode – HID
Step 4: The scanner will beep twice and cradle’s
blue indicator LED will stay on to verify a
successful connection.
If the host does not support Wireless communication,
a third-party Wireless adaptor is required.
Pincode Setup
Step 1: Scan the [DISCONNECT] barcode.
Disconnect
If you are connecting it to a device or mobile
smart phone that is Bluetooth-enabled
technology compatible, you will need to use the
following steps.
Step 1: Scan the [Pincode-Start] barcode when
you are asked by Wireless application to
enter a pincode
Pincode-Start
Step 2: Scan the [Wireless mode - HID] barcode, and
the scanner will emit 8 beeps.
(4)
(5)
(6)
(7)
Wireless mode - HID
(8)
Step 3: Select “Wireless Scanner” from the
discovered
device list.
Step 2: Scan the numeric barcodes according to
the pincode generated by the Wireless
application, and then scan the [Enter]
barcode, as shown in the pincode list
below.
Step 3: Scan the [Pincode-Stop] barcode.
Pincode - Stop
Step 4: The Wireless application may prompt you to
scan a pincode (see PINCODE SETUP
section)
it generates.
Step 5: The scanner will beep twice and cradle’s blue
indicator LED will stay on to verify a
successful connection.
(9)
[Enter]
Step 4: The scanner will beep twice to verify a
successful connection.
※ SCM does NOT support the MS380B.
Unitech electronics co., ltd.
5F., No.135, Ln. 235, Baoqiao Rd., Xindian Dist., New Taipei City 231, Taiwan (R.O.C.)
y Tel: + 886 2 89121122 y Fax: +886 2 89121810 y website: www.ute.com
Ver.1.2
http://www.ute.com/