10 PIECE LOW VOLTAGE
GARDEN LIGHT SET
■ STOCK No.61757
■ PART No.GL10
• INSTRUCTIONS •
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY TO ENSURE THE
SAFE AND EFFECTIVE USE OF THIS TOOL.
04/2000
SPECIFICATION
Whilst every effort has been made to ensure that the accuracy of information
given in this booklet is correct at time of going to print, the Draper Tools policy
of continuous improvement determines the right to change specification
without notice.
Bulb wattage
7W
Transformer input
230V/50Hz
Transformer output
12V/60V.A. 5A
Cable length
18 M (approx.)
CHECKING CONTENTS
1.
2.
3.
4.
5.
6.
Tier A
Tier B
Tier C
Lampshade
Bulb(12V/7W, wedge based) inc. spare
Socket
8 pieces 7. Cable (SPT-1 18ANGx2C 105° 1M)
8 pieces 8. Connector
8 pieces 9. Stem
8 pieces 10. Stake
10 pieces 11. Transformer
8 pieces 12. Floodlight
8
1
1 piece
8 pieces
8 pieces
8 pieces
1 piece
2 pieces
7
11
2
10
3
5
12
6
4
-1-
9
GARDEN LIGHT ASSEMBLY INSTRUCTIONS
This light set contains two garden floodlights which are already assembled.
However the louvred garden lights should be assembled as follows:
1. Press the top of the lampshade into Tier A.
2. Slide Tier B onto the tapered end of the lampshade and secure in the
slots provided.
3. Secure Tier C onto the bottom of the lampshade by aligning each lug
with the slots provided on Tier C. The most efficient way to secure Tier C
to the lampshade is to use both thumbs either side of each lug and push
down until they click into place.
4. Loop the cable over the top of the connector and push it into the recess
provided on each side. Note the arrows moulded on the connectors,
indicating the top.
5. Push the connector into the stem and gently pull the cable down. If low
level lighting is required, omit the stem and connector and loop the cable
over the top of the stake instead.
6. For standard height lighting, push the stake into the other end of the stem.
7. Slide the connector into the socket by aligning the exposed cable with
the flat inner walls of the socket. Push the connector firmly in until it is
secured.
8. Carefully push the bulb into the top of the socket.
9. Insert the socket into the underside of Tier C by aligning the lugs with
the grooves and twist the socket into place.
10. Carefully push the garden light into soft ground. If the ground is hard,
prepare a small hole.
11. Repeat the above procedure for each light.
1.
2.
3.
4.
5.
Tier A
Tier B
Tier C
Lampshade
Bulb
4
12
5
8
6
10
9
7
11
-2-
6.
7.
8.
9.
10.
11.
12.
3
2
Socket
Cable
Connector (0ptional)
Stem (optional)
Stake
Transformer
Floodlight
1
TRANSFORMER INSTALLATION
AND OPERATION
1. The transformer supplied with this light set is not weatherproof, therefore it
MUST ONLY be installed indoors.
2. Place the transformer in a safe, dry position where there is a protected mains
supply power socket.
3. The transformer must not be placed in a confined space, as this may cause it
to overheat.
4. The transformer is fitted with a 1.5 metre (approx.) power supply cable and 3
pin 5A fused plug. The cable and plug must not be exposed to harsh
treatment.
5. The transformer is also supplied with a 18 metre (approx.) 12 volt, low
voltage cable (SPT-1 18AWG x2C 105°). After the light assemblies have been
pushed into the ground, stretch the cable out to the desired route following
where the garden lights have been positioned.
6. The garden light kit will be switched "ON" or "OFF" at the mains supply
power socket in which the transformer is plugged.
GARDEN LIGHT KIT CONNECTION
OUTSIDE
INSIDE
NOTE:
Place the transformer in a
safe, dry position where there
is a protected mains supply
power socket.
-3-
BULB REPLACEMENT
Spare bulbs are available, quote Stock No.62155 (pack of 4).
1. Twist the lampshade while holding the socket and stem/stake firmly.
2. Lift off the lampshade to expose the bulb.
3. Gently pull the bulb out of the socket, to avoid it breaking off (caution: may
be hot!).
4. Carefully insert the specified replacement bulb (8W) into the top of the
socket, taking great care not to twist or force it, as this will break it.
5. Replace the lampshade and twist into place.
GUARANTEE
Draper Garden Lights have been carefully tested and inspected before
shipment and are guaranteed to be free from defective materials and
workmanship for a period of 12 months from the date of purchase except where
items are hired out when the guarantee period is ninety days from the date of
purchase.
Should the unit develop any fault, please return the complete item to your
nearest authorized warranty repair agent or contact Draper Tools Limited,
Chandler’s Ford, Eastleigh, Hampshire. SO53 1YF. England.
Telephone: (023) 8049 4333.
If upon inspection it is found that the fault occurring is due to defective
materials or workmanship, repairs will be carried out free of charge. This
guarantee does not apply to normal wear and tear, nor does it cover any
damage caused by misuse, careless or unsafe handling, alterations, accident, or
repairs attempted or made by any personnel other than the authorized Draper
warranty repair agent.
This guarantee applies in lieu of any other guarantee expressed or implied and
variations of its terms are not authorized.
Your Draper guarantee is not effective unless you can produce upon request a
dated receipt or invoice to verify your proof of purchase within the 12 month
period.
Please note that this guarantee is an additional benefit and does not affect your
statutory rights.
Bulbs are consumable item and are not covered by this guarantee.
Draper Tools Limited.
-4-
NOTES
-5-
NOTES
-6-
DRAPER TOOLS LIMITED,
Hursley Road, Chandler's Ford,
Eastleigh, Hants. SO53 1YF. England.
Tel: (023) 8026 6355.
Fax: (023) 8026 0784.
www.draper.co.uk
e-mail: [email protected]
YOUR DRAPER STOCKIST
©Published by Draper Tools Ltd.
No part of this publication may be reproduced,
stored in a retrieval system or transmitted in
any form or by any means, electronic, mechanical
photocopying, recording or otherwise without prior
permission in writing from Draper Tools Ltd.