Proceeding of 2nd Nuclear Energy Technology Seminar
Denpasar, October 15-16, 2015
ISSN: 2355-7524
TYPE THE TITTLE OF YOUR PAPER, CAPITALIZE EACH WORD,
MAXIMUM 14 WORDS, ARIAL TYPE 12 BOLD
A. Firstauthor1, B. Secondauthor1, D. Thirdauthor2 (Arial 10 bold)
1First affiliation, Address, City and Postcode, Country (Arial 9 Italic)
2Second affiliation, Address, City and Postcode, Country (Arial 9 Italic)
Email: [email protected]
ABSTRACT
WRITE TITLE OF YOUT PAPER HERE IN CAPITAL FOR EACH WORD ARIAL TYPE 10
BOLD. These instructions give you guidelines for preparing papers for SENTEN. Use this
document as a template using Microsoft Word 2003 or later. The electronic file of your paper
will be formatted further at seminar secretary. Abstract should be no longer than 200 words,
giving a brief summary of the background, methodology, and conclusions. Do not include
artwork, tables, elaborate equations or references to other parts of the paper or to the
reference listing at the end. Words use Arial Font 10 and 1 spacing line.
Keyword: keyword1, keyword2, keyword3, keyword4, keyword5
ABSTRAK
(FOR INDONESIA CITIZEN ONLY) TULISKAN JUDUL KARYA TULIS ILMIAH DI SINI
DENGAN HURUF BESAR SEMUA TIPE ARIAL 10 BOLD. Instruksi ini diberikan sebagai
panduan untuk mempersiapkan karya tulis ilmiah untuk SENTEN. Gunakan document
template ini. Electronic file dari karya tulis anda akan disesuaikan lebih lanjut oleh sekretaris
seminar. Abstrak harus tidak lebih dari 250 kata, dengan memberikan tulisan singkat tentang
latar belakang, metodologi, dan kesimpulan. Tidak diperbolehkan memasukkan hasil
gambar, tabel, persamaan atau daftar pustaka yang akan ditempatkan dalam bagian lain
dari karya tulis ilmiah ini. Huruf menggunakan Arial dengan font 10 dan 1 spasi.
Kata kunci: kata kunci1, kata kunci2, kata kunci3, kata kunci4, kata kunci5.
INTRODUCTION, ARIAL 10 BOLD
State the objectives of the work and provide an adequate background, state of the
art, avoiding a detailed literature survey or a summary of the results. Reference numbers
should be indicated in the text by square brackets, e.g. [1], or [1,3], or [1-3]. Words for
explanation use Arial with font size of 10 and 1 spacing lines.
THEORY/CALCULATION/MODELING (if any), ARIAL 10 BOLD
Theory section should extend, not repeat, the background to the article already dealt
with in the Introduction and lay the foundation for further work. In contrast, a Calculation
section represents a practical development from a theoretical basis. Do not copy-paste the
equation from pdf file or other document in picture mode. This copy-paste may effect on low
quality printing. The example of equation that could be followed is describe below”
dCi (t ) Bi (t )

P(t )  i Ci (t ), i  1,... 6
dt

(1)
METHODOLOGY, ARIAL 10 BOLD
Provide sufficient detail to allow the work to be reproduced. Methods already
published should be indicated by a reference. Only relevant modifications should be
described.
RESULT AND DISCUSSION, ARIAL 10 BOLD
Results should be clear and concise. Discussion should explore the significance of
the results of the work, not repeat them. A combined Results and Discussion section is often
appropriate. Avoid extensive citations and discussion of published literature.
Seminar Secretary will do the final formatting of your paper, so you do not need to
position figures and tables at the top and bottom of each column. In fact, all figures, figure
1
Type the tittle … (a half row only, ended with 3 points “…”)
A. First author (if more than one, write “A.First author, et al.”)
ISSN: 2355-7524
captions, and tables can be at the end of the paper. Large figures and tables may span both
columns. Place figure captions below the figures; place table titles above the tables. In case
there is any difficulties to arrange the figure(s) and Table(s) in appropriate place, they can be
placed at the end of this template.
590
570
560
550
5
Coolant velocity [m/s]
Temperature [C]
580
6
Laminar
k-epsilon
k-omega
RSM
Spalart Allmaraz
4
3
2
Laminar
k-epsilon
k-omega
RSM
Spalart Allmaraz
540
1
530
0.00 0.01 0.02 0.03 0.04 0.05 0.06 0.07 0.08
0
0.00 0.01 0.02 0.03 0.04 0.05 0.06 0.07 0.08
Position Z [m]
Fig. 1. Figure is shown in high resolution and
considered to be print in gray color.
Position Z [m]
Fig.2. Explanation of figure must be written
in the paper.
Figure 1 explains that the material for figure must be shown in high resolution and
considered to be printing in gray color. The explanation of figure must be written in the paper
as well as described in Fig. 2. The table may be formatted as picture with setting as
explained above and has high resolution.
CONCLUSION, ARIAL 10 BOLD
A conclusion contains the main points of the article. It should not replicate the
abstract, but might elaborate the significant results, possible applications and extension of
the work.
ACKNOWLEDGMENT (OPTIONAL), ARIAL 10 BOLD
Acknowledgment is recommended to be given to persons or organizations helping
the authors in many ways. Sponsor and financial support acknowledgments may be placed
in this section. Use the singular heading even if you have many acknowledgments.
REFERENCE, ARIAL 10 BOLD
1. IAEA-TECDOC-1382, “Evaluation of High Temperature Gas Cooled Reactor
Performance: Benchmark Analysis Related to Initial Testing of The HTTR and HTR-10”,
IAEA, November, Vienna (2003).
2. Dixon A.G., et al., “Systematic Mesh Development for 3D CFD Simulation of Fixed Beds:
Single Sphere Study”, Journal of Computer and Chemical Engineering, Vol.35, Issue 7,
pp.1171–1185 (2011).
3. Dehbi A. and Martin S.,”CFD Simulation of Particle Deposition on An Array of Spheres
Using an Euler/Lagrange Approach”, Journal of Nuclear Engineering and Design,
Vol.241, pp.3121–3129 (2011).
4. Kuijper J.C. et al., “HTTR-N Reactor Physics and Fuel Cycle Studies”, Proceeding of 2 nd
International Topical Meeting on High Temperature Reactor Technology, September 2224, Beijing (2004).
2