Appendix A. Tanking and sump pumps manufacturer brochure
1
DELTA MEMBRANE SYSTEMS LTD.
DELTA SYSTEM 500
‘Providing Waterproofing Solutions’
Uniclass
L6813
CI/SfB
(13.9)
Ln6
(L34)
February 2012
DELTA
Appendix A. Tanking and sump pumps manufacturer brochure
The Sealed System
solution in Heritage type properties
In soil retaining situations such
as a general damp proofing
as basements and vaults etc.
system. The fabric of the building
the DELTA sealed system is
remains unchanged but the new
recommended. The membrane
internal surfaces are ‘dry’ and are
selection depends on the required
salt and contamination free. Both
finish and flow rate if applicable.
dry lining or plaster direct finishes
All membrane junctions, fixing
are available on the ventilated
points, service entries and other
system.
2
DELTA
reliance on the ability of the
product to bond to the substrate.
protrusions are sealed with the
DELTA range of sealing products.
Floors
Where active ground water is
As well as being a complete
evident or expected drainage of
waterproofing and damp proofing
one form or another should be
system, the DELTA system is also
incorporated into the specification.
used to upgrade damp and
Our technical staff are available to
defective floors. With excellent
give advice in this respect.
crush resistance the system lends
The DELTA system can be applied
itself to a variety of different
finishes which include conventional
The Ventilated
System
screeds, thin layer fast drying
In above ground situations or in
floors. Insulation can also be used
to a variety of different substrates
areas where no free running water
in conjunction with the system
for example over existing renders
is expected, for example where
where required. The system can be
or broken down bitumen coatings,
external pavements have been
linked to the D.P.C. constructed
etc. This can be easily achieved
built up, the ventilated system can
within a new wall or to an existing
without detriment to the integrity
be used. The ventilated system
D.P.C.
of the system.
Preparation
As the membrane systems are
Damp Pressure
Equalisation
mechanically fixed there is no
The studded structure of the
with air gap at top and bottom,
with sealed joints and fixings is
sufficient in this situation. This
method
d is seen as a sympathetic
e
screeds and wood based floating
membrane allows the dampness
behind the membrane to move in
all directions unhindered, therefore
the whole of the wall or floor
surface takes the damp loading.
Break downs created by weak
points are eliminated. The product
does not divert the problem to
other areas.
Flexibility
In structures where movement or
vibration can be a problem,
examples being under street vaults,
railway arches, and buildings
constructed with movement joints,
Appendix A. Tanking and sump pumps manufacturer brochure
3
the DELTA system can cope. The
DELTA membrane has an
elongation break of greater than
50%.
Speed
As there is little or no preparation
required the system is by
comparison quick to install. When
dry finishes are used the system is a
‘fast track’ solution. Decoration
does not need to be delayed as
there is no drying process.
DELTA Membrane Systems is the
U.K. arm of the world’s largest
producer of cavity drain systems.
cavity membranes has been
The market leading DELTA brand
generally accepted in the U.K.
The Membranes
has a track record approaching
DELTA Systems are a complete
DELTA-MS 500 This is used for walls
three decades. The DELTA systems
range of products which are used
and floors, and is supplied in 2.4, &
have been used successfully in
together to solve many of today’s
2m x 20m rolls. This membrane can
many situations in the U.K, from
problems in both new and old
be used for light water ingress
small domestic basements up to
construction. DELTA Systems can
situations, and is available yellow
major waterproofing projects such
easily deal with aggressive ground
(DELTA-FM), and clear. The MS
water conditions, where basements
500 clear aids the selection of good
are liable to flooding, or indeed
fixing points in more difficult
where simple dampness,
application i.e. random stone and
contamination or salting problems
friable brickwork. The sealed DELTA-
are prevalent. Other more diverse
Plug or Qwik Seal Plug is used to
applications include turf covered
secure System 500, the centre
roofs, barn conversions, tunnel
shank of this fixing is also used for
linings or even as a barrier against
subsequent dry lining applications.
radon gas.
DELTA PT LATH This membrane
The main components of the system
has a mesh incorporated on the
are the membranes themselves.
internal face which is attached by a
as London Underground stations.
These are manufactured from
thermic welding process at the
There is rarely a dampness or water
virgin high density polyethylene
time of manufacture. The sealed PT
ingress problem that falls outside
which is thermally and alkaline
fixing plug is used to secure the
the scope of the capabilities of the
stabilised. The stud heights vary
DELTA system.
from 3mm for DELTA-FM, 8mm
for DELTA MS 500 & DELTA PT to
What are DELTA
Systems
20mm for DELTA MS 20. The
With the introduction of British
contains between 2.1 and 10 litres
Standard BS.8102:2009 ‘Protection
of space respectively. This is known
of below ground structures against
as either the ‘Air Gap’ or the
water from the ground’, the use of
‘Drained Cavity’, in wet situations.
cavity created by the membrane
Appendix A. Tanking and sump pumps manufacturer brochure
4
membrane at 250mm horizontal
used as a ‘cavity former’ for many
and vertical centres. The welded
types of new construction. The rolls
Who Installs
DELTA Systems
mesh and fixing plugs allow for
are a full 2 metre width by 20
Although DELTA systems are by
direct render 1.1.6.
metres in length (40m ).
comparison, easy to install, it must be
2
recognised that correct diagnosis of
(cement/lime/sand), or plasters:
Tarmac Whitewall, Carlite Bonding,
Product Guarantee
the problem is essential so that
or dab fixed plasterboard for internal
DELTA membrane systems can
DELTA systems can be designed and
applications. When this grade is
come with a thirty year product
tailored to the needs of the building,
used for external above ground
guarantee when installed by
to give the best possible performance.
protection polymer renders can be
registered installers. The guarantee
It is therefore recommended that
used as a finish. These renders are
covers the membrane and ancillary
only competent specialist contractors,
polymer modified and can also have
components. Based on experience,
who understand dampness, and
reinforcing fibres incorporated for
accelerated ageing tests and a
the associated problems, be
added strength and durability. This
quality manufacturing system to
employed to survey the site, install
grade is available in clear 2.0m x
ISO 9001, the DELTA range can
the system and thereby ensure the
20m (40m ),1.5m x 10m (15m ) or
also be guaranteed with confidence.
best possible performance of the
2
2
1.0m x 15m (15m ).
system. DELTA systems are installed
2
by a nationwide network of
DELTA MS 20 This is a heavy
Technical site and/or
office visits
gauge version of System 500 with
Staff are available to visit site to give
holders of ‘Registered Installers’
deep 20mm studs. This is used
advice on particularly difficult or
Certificates. These contractors also
where extra drainage capacity is
unusual situations, where appropriate
offer guarantees for their
required, for example on deeper
specifications are prepared to assist
workmanship, giving peace of
structures, or where a larger flow
in the correct use of the system.
mind to the client.
specialist contractors who are
rate is required. MS 20 can also be
COMPLETED BASEMENT PROJECTS
DELTA
Leisure
Study
Photography Studio
Playroom
Home Cinema
Music Room
Appendix A. Tanking and sump pumps manufacturer brochure
5
®
DRAINAGE OPTIONS
DELTA SUMPS & PUMPS
DELTA
When specifying a sealed cavity membrane system, full consideration must
be given to drainage, when installed below ground.
The concept of the drained cavity system is to collect and manage any
moisture which breaches the integrity of the structure by channelling,
collecting, and discharging such free water via a suitable evacuation point.
Channels, laid to falls, can discharge passively into a sump or be connected
to a drainage system but access for maintenance should be provided.
Access ports allow inspection and water jetting of channels, while sumps
have a sealed access cover which allows for annual maintenance checks to
be carried out, which are recommended.
If drainage has been installed, it should be flood tested before covering it up
to make sure the system works.
Delta offer a choice of sump+pump stations to fit the purpose, and free
advice is available from their technical staff.
Service agreements can be arranged through Delta and are maintained by
PPS Ltd.
Delta Retrofit Sumps are fitted with a dual pump system and have three
110mm/160mm side inlets to take ground water, and grey water from
shower, laundry and sink waste.
®
DELTA® CHANNEL
DELTA AQUADUCT
DELTA
Delta Channel is a water collection conduit which is bedded into a preformed channel at
the floor/wall angle. Holes in the channel wall allows water to ingress at this point to drain
away to a sump or soak away. Access ports are available to allow maintenance and
inspection. The system is joined with a range of connectors.
Delta Aquaduct is a drainage channel which acts as a perimeter conduit bedded in at the
floor/wall angle. Where appropriate, it can be laid under the slab to take off ground water
to a sump or soak away, and reduce flotation pressures from bearing on the slab.
Delta Aquaduct is fully perforated for maximum performance, and incorporates an outer
geotextile filter to prevent particles from entering the channel.
The product comes on a roll 150m x 60mm diameter. It is also available in 100m x 100mm
dia rolls.
'FREE LIME' RISK
When new concrete forms the structure, to walls or particularly floors, there is a risk of
excess free lime leaching out during the curing process.When a cavity drainage system is
used in this type of application, a silicification pre-treatment of the concrete should be
used to prevent the risk of free lime build up, and blockage of the drainage cavity. Delta
Polysil-TG 500 is applied by spray for this purpose, and is available in 10kg drums.
POWER FAILURE?
HELP IS AT HAND
DELTA
If you've installed a cavity drained system internally, one of the main
design considerations is how are you going to manage the water
collection and discharge. This can be done passively into existing
drainage points, if available and appropriate.
However, the majority of projects require a collection sump + pump,
to automatically manage the evacuation of any water ingress. This
type of unit requires mains power to operate, so what can be done if
the power fails, and is coincident with high water ingress? Here are
two options from Delta.
High Water Level Alarm - This system gives an audible warning if
a high level situation occurs. It is fitted with it's own rechargeable
battery, which is trickle charged , and will still operate in the event of
mains power failure.
Delta Power Pack Pumps 8,100 Ltr in back up mode.
Delta Power-Pack -This unit is designed to run the secondary pump
if a power failure occurs. The unit is trickle charged under normal
conditions, and will auto switch to battery power if mains power fails.
The unit will pump approx. 8,100 litres in back up mode.
Appendix A. Tanking and sump pumps manufacturer brochure
DELTA®-MS 500:
6
DELTA®-MS 20:
Cavity drainage membrane
Dimpled sheeting with
for use on walls and floors,
particularly high drainage
as a waterproof system. A
capacity and compressive
choice of finishes are
strength, suitable for high
available. Can also be used
performance seepage layers
externally for waterproof
in building and civil
protection of sub-ground
engineering construction.
structures.
Material:
Thickness:
Stud height:
Roll size:
(With flat edge of 7 cm
on one side)
Compressive strength:
Drainage capacity:
Air volume between studs:
Temperature resistance:
Chemical properties:
Behaviour in fire:
high density polyethylene
approx. 0.6 mm
approx. 8 mm
available in clear
2.4 x 20 m
2.0 x 20 m
> 250 kN/m2
approx. 2.25 l/s · m
approx. 135 l/min · m
approx. 8 100 l/h · m
approx. 5.3 l/m2
– 30°C to + 80°C
resistant to chemicals, resistant to
root penetration, rotproof, neutral
towards drinking water
Class E
DELTA®-PT:
Material:
Thickness:
Stud height:
Roll size:
Compressive strength:
Drainage capacity:
Air volume between studs:
Temperature resistance:
Chemical properties:
Behaviour in fire:
high density polyethylene
approx. 1 mm
approx. 20 mm
2.0 x 20 m
In the case of special requirements,
also available in board format
approx. 150 kN/m2
approx. 10 l/s · m
approx. 600 l/min · m
approx. 36 100 l/h · m
approx. 14 l/m2
– 30°C to + 80°C
resistant to chemicals, resistant to
root penetration, rotproof, neutral
towards drinking water
Class E
DELTA®-FM:
DELTA®-FM
is
specifically
designed for floor applications,
to combat dampness, and
contamination. The special low
stud profile (3mm) minimises
changes in floor levels but still
provides an air gap to achieve
damp pressure equalisation.
Dimpled sheeting with plastic
mesh welded on, suitable as a
damp-proof base for plaster or
shotcrete, e.g., as a seepage
layer in tunnel construction, or
for repairing basements
internally.
Material:
Thickness:
Stud height:
Roll size:
Compressive strength:
Drainage capacity:
Void between studs:
Temperature resistance:
Chemical properties:
Behaviour in fire:
high density polyethylene
approx. 0.5 mm
approx. 8 mm / 8mm / 4mm
2.0 x 20 m / 1.5 x 10 m / 1.0 x 15m
approx. 70 kN/m2
approx. 5 l/s · m
approx. 300 l/min · m
approx. 18 100 l/h · m
approx. 5.5 l/m2
– 30°C to + 80°C
resistant to chemicals, resistant to
root penetration, rotproof, neutral
towards drinking water
Class E
The membrane is a fast-track
application that allows various
floor finishes to be achieved with
zero ‘down time’. The R.H. levels
are isolated in the air gap, and
controlled. Delta-FM can be used in new build, remedial or refurbishment projects for
floors, and walls.
Material:
Virgin high-performance PE-VHD
Application:
Special low stud profile for floor.
Can be used on walls
Sheet thickness:
approx. 0.6 mm
Dimple height:
approx. 3 mm
Compressive strength:
approx 140 kN/m2
Roll dimensions:
20m x 2m (40m2)
Volume between dimples:
approx 2.1 1/m2
Service temperature range:
-30degC / +80degC
Behaviour in fire:
Class E
Delta Membrane Systems Ltd.
© DELTA MEMBRANE SYSTEMS LTD 1998
DELTA
02/13
Delta Centre,
House, Merlin
Way, North
CM16Essex
6HR CM16 6AA
Bassett Business
Hurricane
Way,Weald,
NorthEpping,
Weald,Essex
Epping,
Telephone: 01992
Fax: 01992
Telephone:
01992 523
523523
811 Fax:
01992 523
524250
046
e-mail: [email protected] www.deltamembranes.com
Appendix A. Tanking and sump pumps manufacturer brochure
7
Uniclass: L7316
CI/SfB:
(52.9)
X
DELTA MEMBRANE SYSTEMS LTD
packagedpumpsolutions
Bespoke Pump Chambers
DELTA MEMBRANE SYSTEMS LIMITED
DELTA HOUSE, MERLIN WAY, NORTH WEALD, EPPING, ESSEX, CM16 6HR
t: 01992 523523 e: [email protected] www.deltamembranes.com
Appendix A. Tanking and sump pumps manufacturer brochure
8
Overview
The Dual V4 & V6 are upgrades to the standard Dual V3 where higher discharge heads are required. Typically for double and triple depth
basements or where long discharge runs are required resulting in higher than normal pipe work losses. The Dual V4 and V6 are suitable for
picking up ground water from a cavity membrane systems and light wells, totalling up to 12m².
800
345
290
250
902 overall
310 access
660
CABLE DUCT
2" / 50 mm FEMALE
TO ACCEPT STD.
DRAINAGE PIPE
Pump Model
V4P
V6P
Voltage
230
230
KW Rating P1/P2
0.75 / 0.356
1.050 / 0.50
Full Load Current
1.0A
1.9A
Fuse Spur Rating
13A
13A
Typical Duty
2.0 l/s @ 7m
2.0 l/s @9m
Total Storage Volume
273 Litres
273 Litres
Storage Below Invert
137 Litres
137 Litres
UPS
Power Plus
Power Plus
DISCHARGE
2" BSP / 50 mm MALE
IRON SUPPLIED LOOSE
Accessories
Battery Back up
- Power Plus
High Level Alarm
Telemetry System
Pipe Work
Appendix A. Tanking and sump pumps manufacturer brochure
9
Overview
The 800mm x 1300mm deep range of chambers are
typically used where inverts are required to be deeper
than the standard Delta Dual V3,V4 & V6 & foul V3
(345mm from cover level). For example in buildings where
drainage runs are long or drainage is running below floor
slabs 250mm or thicker. Inverts can be up to 775mm from
top of structural slab.
Table 2
Typical Duty
Ground /
Surface Water
Foul Water
Solids Passage
Pump
Installation
Pump Type
UPS
2-800-1300-U-V3
2l/s @ 4m head
YES
NO
10mm
Free Standing
V3
Battery Backup
2-800-1300-U-V4
2l/s @ 7m head
YES
NO
10mm
Free Standing
V4
Power Plus
2-800-1300-U-V6
2l/s @ 9m head
YES
NO
10mm
Free Standing
V6
Power Plus
1-800-1300-612SA-GR
4l/s @ 7m head
NO
YES
50mm
Guide Rail
612SA
Not Available
1-800-1300-712SA-GR
4l/s @ 5m head
NO
YES
65mm
Guide Rail
712SA
Not Available
Accessories
Battery Back up
- Power Plus
High Level Alarm
Telemetry System
Delta Membrane Systems Limited
Delta House, Merlin Way, North Weald, Essex, CM16 6HR
t: 01992 523 523 e: [email protected] www.deltamembranes.com
Pipe Work
Appendix A. Tanking and sump pumps manufacturer brochure
10
Overview
A range of chambers from 800mm-2630mm deep for collecting ground, surface
and foul water (dependent on pump type) fitted with a range of vortex and
macerator pumps. Full pump duty information on pages 6 & 7 –‘Delta drainage
and sewage pumps- Performance and electrical information’.
588 x 438 access
Top View, 800
diameter chamber
Cutaway view of 800mm
dia x 1800mm deep with
guide rail mounted
50mm pump
The full range of 800 series chambers.
2000
1800
1500
1300
1000
800
Appendix A. Tanking and sump pumps manufacturer brochure
11
Depths (mm)
Diameters (mm)
800
1000
1140
1300
1500
1540
1800
1940
2000
2630
800
YES
YES
NO
YES
YES
NO
YES
NO
YES
NO
1160
NO
NO
YES
NO
NO
YES
NO
YES
NO
YES
Typical 1140mm deep chamber.
DISCHARGE
2 BSP Fema e
0
145
110
600 600 access
255
360
510
160
1160
CABLE DUCT
DN 110 sea
110 mm a
ENT
DN 110 sea
110 mm a
acce s a
a e
e
a
acce s a
a e
e
a
1020
1140
The full range of 1160 chambers.
2630
1940
1540
1140
Delta Membrane Systems Limited
Delta House, Merlin Way, North Weald, Essex, CM16 6HR
t: 01992 523 523 e: [email protected] www.deltamembranes.com
Appendix A. Tanking and sump pumps manufacturer brochure
12
PPerformance
erformance aand
nd eelectrical
lectrical iinformation
nformation
Overview
A range of drainage and sewage pumps fitted to our standard V3 products as well as larger 800 & 1160 series bespoke chambers.
Featuring a range of single and three phase pumps with vortex impellors and macerator cutting systems. Pumps are generally
available in automatic for control via an integral float switch or manual to be controlled via an external control panel. Applications
covered include ground, surface and foul water, with the emphasis on high quality and low whole life costs. Pumps fitted to standard
products are removed using quick release couplings, larger pump stations have pumps on ‘guide rail’ system with simple removal via
lifting chains. We offer a range of accessories fitted as standard to our pump stations as stand alone products when fitting pumps
inside pre cast chambers or concrete rings, including pipe work, gate and non return valves.
V3, V4 & V6 (Free Standing)
50Hz - 1 ~ 230V Discharge 1 1/4” BSP Female
12
Model
P1
P2
kW
kW
V3
0.430
0.180
1.9
DMS - 116
5.64
V4
0.750
0.356
4.0
DMS - 216
7.17
V6
1.050
0.500
4.9
DMS - 084
7.40
Part No.
Weight
H[m]
10
8
In A
Part No.
Weight
Kg
6
4
V3
V4
V6
2
0
0
1
2
4
3
Q[l/s]
OPWB 308 & 309 (Guide Rail)
12
50Hz - 1 ~ 230V
H[m]
Model
P2
MAX
Nominal
W
kW
OPWB 308
355
0.22
1.6
4.6
OPWB 309
800
0.55
3.4
6.7
10
8
6
4
2
0
OPWB
308
309
0
1
2
3
4
5
Q[l/s]
Discharge 1 1/4” BSP Female
P1
In A
Kg
Appendix A. Tanking and sump pumps manufacturer brochure
13
600 Series (Free Standing & Guide Rail)
18
50 Hz - 1~ 230V Discharge 2” BSP Female
H[m]
16
Model
14
12
10
8
P1
P2
kW
kW
IN
(A)
ID
(A)
Part No.
Weight
611 SA
1.0
0.55
5.0
18.2
612 SA
1.25
0.75
6.0
18.2
613 SA
1.8
1.1
8.2
18.2
22
614 SA
1.8
1.1
8.2
18.2
22
Kg
22
DMS - 114
22
50 Hz - 3~ 400V
6
4
2
0
0
4
2
6
8
Q[l/s]
611
612
613
614
611 TM
0.9
0.55
2.3
18.3
22
612 TM
1.1
0.75
2.8
18.3
22
613 TM
1.5
1.1
3.0
18.3
22
614 TM
2.05
1.5
3.5
18.3
22
700 Series (Guide Rail)
14
50 Hz - 1~ 230V Discharge 2 1/2” BSP Female
H[m]
Model
12
10
8
6
P2
kW
kW
IN
(A)
ID
(A)
Part No.
Weight
Kg
712 SA
1.25
0.75
6.0
18.2
25
713 SA
1.8
1.1
8.2
18.2
25
714 SA
1.8
1.1
8.2
18.2
25
712 SM
1.25
0.75
6.0
18.2
25
713 SM
1.8
1.1
8.2
18.2
25
714 SM
1.8
1.1
8.2
18.2
25
50 Hz - 3~ 400V
4
712
713
714
2
0
P1
0
2
4
6
8
10
Q[l/s]
712 TM
1.1
0.75
2.8
18.3
25
713 TM
1.5
1.1
3.0
18.3
25
714 TM
2.05
1.5
3.5
18.3
25
12
TC656 (Guide Rail)
50 Hz - 1~ 230V Discharge 2” BSP Female
20
Model
HMTm
15
P1
P2
kW
kW
IN
(A)
ID
(A)
TC656 SA
1.8
1.1
8.2
18.2
26
TC656 SM
Weight
1.8
1.1
8.2
18.2
26
1.5
3.5
18.3
24
Kg
50 Hz - 3~ 400V
TC6 TM
2.05
10
5
Part No.
TC 656 SA/SM
TC 656 TM
0
1
2
3
4
Q[l/s]
5
Delta Membrane Systems Limited
Delta House, Merlin Way, North Weald, Essex, CM16 6HR
t: 01992 523 523 f: 01992 523 250 e: [email protected] www.deltamembranes.com
Appendix A. Tanking and sump pumps manufacturer brochure
After Sales
Service
14
after sales service
PPS provide comprehensive maintenance and
service support for all installations of Delta
packaged stations.
They have a team of fully trained service
engineers who are able to maintain both Delta
manufactured equipment as well as booster
set/pressurisation set and rain water harvesting
systems.
They offer both one off servicing and repairs as
well as preventative maintenance agreements.
Clients who are on a service agreement have
access to a 24hr/365 day call out facilities.
s&ULLYSTOCKEDVANS
s&U
s%
s%
s%MERGENCYBREAKDOWNSERVICE
s/
s/UTOFHOURSSERVICE
s
s0LANNEDMAINTENANCE
s
s&ACTORYTRAINEDENGINEERS
0!#+!'%$05-03934%-3,4$
UNIT 12 HASLEMERE INDUSTRIAL ESTATE, PIG LANE, BISHOP’S STORTFORD, HERTFORDSHIRE, CM23 3HG
t: 01279 757 400 e: [email protected] www.ppsgroupuk.com
Appendix A. Tanking and sump pumps manufacturer brochure
15
RYHUDOO
DFFHVV
3XPS7\SH
93
3
0.75N:
3
356N:
)/&
.0$
RYHUDOO
6$:12))
62&.(7(1'
'1PP
62&.(7
127 6833/,('
&$%/('8&7
PP)(0$/(
72$&&(3767'
'5$,1$*( 3,3(
',6&+$5*(
%63PP0$/(
,5216833/,('/226(
ĞůƚĂƵĂůsϰ
D^ͲϮϭϳ
ĞůƚĂ,ŽƵƐĞ͕DĞƌůŝŶtĂLJ͕
EŽƌƚŚtĞĂůĚ͕
ƉƉŝŶŐ͕ƐƐĞdžDϭϲϲ,Z
dĞůĞƉŚŽŶĞ͗ϬϭϵϵϮϱϮϯϱϮϯ
ͲŵĂŝů͗ŝŶĨŽΛĚĞůƚĂŵĞŵďƌĂŶĞƐ͘ĐŽŵ
Appendix A. Tanking and sump pumps manufacturer brochure
16
345
290
250
776 overall
902 overall
310 access
Pump Type
V6P
P1
1.1kW
P2
0.5kW
FLC
4.9A
800
SAWN OFF
SOCKET END
DN 100 / 110 mm
SOCKET
(NOT SUPPLIED)
660
CABLE DUCT
2" / 50 mm FEMALE
TO ACCEPT STD.
DRAINAGE PIPE
DISCHARGE
2" BSP / 50 mm MALE
IRON SUPPLIED LOOSE
ĞůƚĂƵĂůsϲ
D^ͲϬϳϵ
ĞůƚĂ,ŽƵƐĞ͕DĞƌůŝŶtĂLJ͕
EŽƌƚŚtĞĂůĚ͕
ƉƉŝŶŐ͕ƐƐĞdžDϭϲϲ,Z
dĞůĞƉŚŽŶĞ͗ϬϭϵϵϮϱϮϯϱϮϯ
ͲŵĂŝů͗ŝŶĨŽΛĚĞůƚĂŵĞŵďƌĂŶĞƐ͘ĐŽŵ
Appendix A. Tanking and sump pumps manufacturer brochure
17
6(3$5$7(&,5&8,76
)520',675,%87,21
%2$5'
7<3,&$/,167$//$7,216&+(0$7,&)25'(/7$'8$/93803$66(0%/<
127(
7+,66&+(0$7,&,6,17(1'('726+2:7+(35,1&,3/()($785(62)$7<3,&$/
,167$//$7,217+(&2175$&7256+28/'$/625()(5727+(&2175$&7
'2&80(176$1',167$//$7,21,16758&7,216)25($&+&20321(17
1R1216:,7&+('
)86('6385
3803$/$50
'21276&$/(',0(16,216)5207+,66&+(0$7,&'5$:,1*
7232)&+$0%(50867%(,167$//('/(9(/:,7+
7232)6758&785$/)/2256/$%250$;PP
)5207232)6&5(('
PP'5$,1$*(3,3(
&872)))/86+$77+(6/$%
&$%/('8&772
7(50,1$7(127
/(667+$1PP
$%29())/
0$;P3803&$%/(,6P
',6&+$5*(3,3(
Î720$,1'5$,1
6&5(('
,168/$7,21
'(/7$06
0(0%5$1(
6/$%
'1,1/(7'5$,1/$,'72)$//6
5()(572352-(&7'5$:,1*6$1'63(&,),&$7,21
)25*5$',(17$1'%('',1*5(48,5(0(17
3803&+$0%(572%(,167$//('8321PP0,1
&21&5(7(%('$1'3529,'(':,7+&21&5(7(
6,'(),//$//&21&5(7(72%(*5$'(;;;;
PP&$%/('8&7$//&+$1*(62)
',5(&7,2172%()250(':,7+ (/%2:625/21*5$',86%(1'6
$6$
Appendix A. Tanking and sump pumps manufacturer brochure
18
6(3$5$7(&,5&8,76
)520',675,%87,21
%2$5'
7<3,&$/,167$//$7,216&+(0$7,&)25'(/7$'8$/93803$66(0%/<
127(
7+,66&+(0$7,&,6,17(1'('726+2:7+(35,1&,3/()($785(62)$7<3,&$/
,167$//$7,217+(&2175$&7256+28/'$/625()(5727+(&2175$&7
'2&80(176$1',167$//$7,21,16758&7,216)25($&+&20321(17
1R1216:,7&+('
)86('6385
3803$/$50
'21276&$/(',0(16,216)5207+,66&+(0$7,&'5$:,1*
7232)&+$0%(50867%(,167$//('/(9(/:,7+
7232)6758&785$/)/2256/$%250$;PP
)5207232)6&5(('
PP'5$,1$*(3,3(
&872)))/86+$77+(6/$%
&$%/('8&772
7(50,1$7(127
/(667+$1PP
$%29())/
0$;P3803&$%/(,6P
',6&+$5*(3,3(
Î720$,1'5$,1
6&5(('
,168/$7,21
'(/7$06
0(0%5$1(
6/$%
'1,1/(7'5$,1/$,'72)$//6
5()(572352-(&7'5$:,1*6$1'63(&,),&$7,21
)25*5$',(17$1'%('',1*5(48,5(0(17
3803&+$0%(572%(,167$//('8321PP0,1
&21&5(7(%('$1'3529,'(':,7+&21&5(7(
6,'(),//$//&21&5(7(72%(*5$'(;;;;
PP&$%/('8&7$//&+$1*(62)
',5(&7,2172%()250(':,7+ (/%2:625/21*5$',86%(1'6
$6$