Swing Door
Besam SW200i™
ASSA ABLOY Entrance Systems
Technical Data Sheet
The global leader in
door opening solutions
SW200i Swing Door Operator
The Besam SW200i automatic swing operator is intended for use in exterior or
interior entryways, corridors and a variety of applications. The Besam SW200i
heavy duty (HD) electro-mechanical operator is suitable for use on large
heavy doors, yet adaptable enough to be used in low energy (LE) applications.
The product can be either surface mounted or overhead concealed, on either
side of the door, for pull or push applications. It is suitable for single doors,
double doors and double egress doors fitted with swing clear hinges, offset
pivots or center pivots. The operator is connected to the door leaf with a
range of different arm systems.
Besam SW200i is designed to offer continuous use, a high degree of safety
and maximum performance over the lifetime of your entrance. The Besam
SW200i ensures all-around safety and can be equipped with a full range of
sensor products providing swing door safety that meets or exceeds ANSI
A156.10 standard.
Operator Features and Performance
• LatchRetry:ifthedoordoesnotlatchwhenclosing,theSW200iwill
detect this condition and immediately open the door to 10 degrees and
execute two attempts to latch the door.
• Operator:electro-mechanical,non-handedoperator,24volt,
5/16 hp motor
• On-boardtimingsequencer
• ANSICompliance:Fieldselectablefullpedestrianusage(ANSIA156.10)
and low energy (ANSI A156.19)
• Lowpassfilter(i.e.“delayonmake”)
• DoorWeight:upto700pounds(315kg)peroperator
• Killinputtoclosedoorsimmediately
• DoorSize:upto48”(consultforwidersizes)
• ManualPushForce:adjustablefrom5lbf–15lbf
• HoldOpenTime:adjustablefrom1.5secondsto30seconds
• WindForceDampening:operatormechanicallycounteractstowind
forces, slowing down the opening or closing of the door
• On-board12Vor24Vtransformer
• Doorpositionrelay
• Self-learningset-up–measuresinertiaanddoorweight
• LowPowerConsumption(300watts,2.5amp(max)
L
Door Set-ups:
• StackPressureCompensation:operatorcounteractstopositivestack
pressures,negativestackpressures,andsuddenchangesofstack
pressures to maintain consistent door speeds
• IntelligentTrajectoryControl:operatorknowswherethedoorshouldbe
atalltimesandadjuststorqueaccordingly.Dynamicbrakinghelps
cushion the door during opening to prevent going past 90 degrees, or
during closing to prevent slamming.
• ExtendedClosingTorque(ECT):exclusiveExtendedClosingTorque(ECT)
functionality provides extra torque in the last 10 degrees of closing, if
needed, to close and latch the door. Speed remains constant so the door
stays within ANSI standards.
Left: Single
Below Left: Simultaneous Pair
Below Right: Pair Egress
L
Operation
Authorities
• Automaticsensoractivation(ANSIA156.10)
• UL/CULapproved
• Pushplateactivation(ANSIA156.19orA156.10)
• ULListedFireDoorOperator
• Pushandgofeatureallowingdoortoopenautomaticallywhen
operator senses movement of door (ANSI A156.19)
• UL10C,UL325,UL991,UL244A,UL1998,UL1310
• Powerassistopen–provideseasytoopenpushforces(ANSIA156.19)
• ANSIA156.10/ANSIA156.19
• Internal,pushtoopen,pushtoclose(i.e.,ratchetrelay)(ANSIA156.19)
• CAN/CSA-C22.2NO223-M91andCAN/CSA-C22.2NO223-M92
• SpeedcontrolledExtendedClosingTorque(ECT)toprovidepowerassist
closewithon-boardfunctionalitytoautomaticallyadjusttorquewithout
increasing speed
• CaliforniaStateFireMarshall
• LossofPower:theoperatorcontrolsthedoorclosing,preventing
slamming of door
• SensorPackagesasfollows:
• IBCandCBC
Sensor Packages
ANSI A156.19
• TorqueLimiting:ifpositiveairpressureconditionisremoved,operator
compensates accordingly and will not slam
• Activation:pushplatesperyourselection
• Safetydevices:notrequiredperANSI.Optionaldoormounted
presencesensors(DMPS)areavailable
Door Operator Handings
ANSI A156.10
• Activation:pushplatesperyourselection(motionsensorsor
push plates)
Electric Lock Management
• A202–Besami-AdaptPremium–standalone,adaptedfield,door
mountedpresencesensors(DMPS)
• Operatorpullsdoorclosedbeforeopening,unjammingelectric
latch hardware
• Sequencedoperationbetweenoperatorsforpairsofdoorsallowing
lockreleaseandastragalcoordination
10
6/11/08
• A102–Besami-AdaptFlex–overheadpresencesensor(OPS)and
twodoormountedpresencesensors(DMPS)perleaf(approach
and safety)
• ElectricLockOutput:selectable12VDC,maximum1200mA/24VDC,
maximum 600 mA
• A101–Besami-AdaptFlex-overheadpresencesensor(OPS)and
onedoormountedpresencesensors(DMPS)perleaf(safety)
Sensor Monitoring
• A100–Besami-AdaptFlex–KnowingActapplications–pair
egressonly–motionsensorapproachandsafetysidefor
secondary activation per ANSI A156.10
Besam Entrance Solutions
10
10
6/11/08
6/11/08
• MonitoredDoorMountedPresenceSensors–upondetectionofsensor
failure, the operator will automatically revert to low energy mode
Authorities
• BlankingPotentiometer:tellssensorsonswingsideofdoorwhen
to shut off
• SensorRecognition–learnprocess
• TorqueCancellation–ExtendedClosingTorque(ECT)isdeactivatedif
signal is received from door mounted presence sensors of a possible
obstruction
Aesthetics
• Aestheticallypleasing,lowprofileappearance:4-5/16”(109mm)high
by5-1/8”(130mm)deep
• Continuousheaderforfullwidthofdoor
• Sameheader/housingasBesamPowerSwingandBesamSW100for
consistent sightlines in your facility
• Finishes:anodized,powdercoat,Kynar,clad
5/8’’
4 5/16’’
• OverheadConcealed–
with emergency
breakaway
1 1/2’’
• OverheadConcealed–
center pivoted or offset
pivoted doors
5 1/8’’
1 3/8’’
• SurfaceApplied
1 1/2’’
Configurations
• SideLoad
• BottomLoad
ASSAABLOYEntranceSystems
Tel: 1-866-237-2687 (US) • 1-888-608-9242 (Canada)
[email protected]
assaabloyentrance.us • assaabloyentrance.ca
2 11/16’’
Operator type
Door width
Door weight
Power supply
Power consumption
Auxiliary voltage
Internal control fuse
Electro-mechanical locking device
Door opening
Electro-mechanical
36”–48”(914–1219mm)
100–700lb(45–315kg)
120VAC+10/-15%,50/60hz
Max.300W
24VDC,max.700mA
2xT6,3AH250V
Selectable:12VDC,max.|
1200mA/24VDC,max.600mA
Push:80–110o
withreveal0–12”(0–305mm)
Pull:80–110o
withreveal0–5-1/8”(0–130mm)
PAS:80–95o
(concealed application)
Variablebetween2–12seconds
Variablebetween4–12seconds
1,5-30seconds
-31oFto160oF(-35oCto71oC)
Max.85%
19.8lb(9kg)
Opening time (0 – 80o)
Closing time (90 – 100o)
Hold open time
Ambient temperature
Relative humidity Drive weight unit
(non-condensing)
This product is to be installed internally or externally with suitable
weather protection.
Class of protection
IP20.
Complies with:ANSI/BHMAA156.19,ANSI/BHMAA156.10,UL325,
UL991,UL244A,UL1998,UL1310,UL10C,CAN/CSA-C22.2
NO223-M91,CAN/CSA-C22.2NO247-92andCAStateFireMarshall
ASSAABLOY,Besam,Crawford,TKO,AlbanyandMegadoor,aswords
andlogotypes,areexamplesoftrademarksownedbyASSAABLOY
EntranceSystemsorcompanieswithintheASSAABLOYGroup.
©ASSA ABLOY Entrance Systems AB/TDS.SW200i.CAN-USA-EN-1.0/1411
Besam Entrance Solutions
Technical data subject to change without notice.
• ChoiceofBesami-Adapt™doormountedpresencesensorsystem:
• Lockmonitoringpreventsoperator(s)fromopeningdoor(s)until
releaseofelectrifiedlock