CFAS Enterprises Inc.
After Market Utility Power Equipment Brokerage
Mailto:[email protected]
Turbine URL: http://CFASPower.com/Index.html
Reciprocating URL: http://CFASPower.com/Recips.html
GTG_531R_Fm7EA.doc
GE Frame 7EA DLN To 9VPPM Nox Control
Three (3) Unused 81 Mw GE PG7121ea Gas Turbine Generators
GE PG7121EA Exemplar
Price: Made Available Upon Demonstration of Serious Intent
Guarantee Performance:
Net Output (Base)
Net Heat Rate (Base)
81,330 Kw
10,537 Kj/Kwh
Design Conditions:
Elevation
Design Ambient Temperature
Design Relative Humidity
Inlet System Pressure Drop
Exhaust System Pressure
N/Gas Fuel Heating Value (Lhv)
Combustion System Type
886'
59 Deg. F
60%
3.5 In. H2o
5.5 In. H2o
20,977 Btu Lb
Dln
Equipment Overview:
Primary Fuel
Starting Means
Air Filtration
Natural Gas/Distillate
Electric Motor
Self-Cleaning
Compressor/Turbine Cleaning
Exhaust System
Emissions Control
On 7 Off-Line Compress Water Wash
Side And Up Exhaust
Gas - Dry Low Nox
Generator:
Model
Cooling
Frequency
Power Factor
Power Factor
Generator Excitation
Outdoor Enclosure
7a6 Packaged Air-Cooled
Open Ventilated
60 Hertz
85 Lagging
13800 Volts
Ex2000br - Rotating Brushless
Load Compartment
Control Systems:
Turbine-Generator
Generator Breaker
Speedtronic Mark V (Tmr)
Included In Switchgear Compartment
Emissions Guarantees:
Nox @ 15% O2 (Ppmvd)
Co, (Ppmvd)
9
25
Estimated Performance:
Fuel Type
Output
Heat Rate (Lhv)
Heat Cons. (Lhv) X 10 Power Of 6
Exhaust Flow X 10 Power Of 3
Exhaust Temperature
Exhaust Heat (Lhv) X 10 Power Of 6 502.5
Dual Fuel-Gas/Distillate
71,510 Kw
10,860 Btu/Kwh
776.6 Btu/H
2109
1023 Deg. F
Generator Performance Rating Conditions:
Stator Insulation
Rotor Insulation
Class F
Class F
Performance Rating, Synchronous Generator (Measurement/Base):
Kva
Power Factor
Kw
Rpm
Number Of Poles
Number Of Phases
Frequency
Voltage
Amperes
Connection
Short Circuit Ratio
100,100
0.85
85,085
3600
2
3
60
13800
4188
Wye
0.51
Fuel Supply Pressure Requirements:
Model Series
Combustor
Max Operating Pressure Psig (Kpa)
Pg7121(Ea)
Dln
375
Min Required Pressure Psig (Kpa)
302
Component Weights And Dimensions:
Accessory Compartment
Turbine Compartment
Generator (Air Cooled)
21.54'l X 10.83'w X 12.58'h
60,000 Lbs.
37.92'l X 11.67'w X 12.75'h
293,500 Lbs.
28.39'l X 11.67'w X 11.46'h
330,000 Lbs.
Price: Usd $ 18,400,000.00 Per Set (Fees Inclusive)
General
This Section Provides The General Description, Scope Of The Work, And Supplementary
Requirements For Equipment, Materials, And Services Included For A Gas Turbine Generator
System.
In General, American Standard Specifications Are Quoted Throughout The Contract
Documents, But Alternative Internationally Recognized Standards May Be Substituted
If Approved In Writing By Purchaser. Seller Shall Submit To Purchaser A Detailed Listing
And Description Of The Codes And Standards, Which The Equipment Will Meet
(Exhibit B-1 Fulfills This Requirement), And For Which Substitution Is Being Requested.
Work Included Under These Specifications
The Work Under These Specifications Shall Include Furnishing A Gas Turbine Generator
And Providing Miscellaneous Materials And Services Complete As A Stand Alone
Electrical Power Generating Facility.
All Equipment, Materials And Services Required For A Complete Gas Turbine And
Generator Unit Shall Be Furnished, Except As Specified Otherwise In These Specifications.
The Equipment And Materials To Be Furnished Shall Include, But Not Necessarily Be
Limited To, The Following Major Items:
Enclosed Gas Turbine
Enclosed Packaged Generator
Generator Lifting Attachments
Enclosed Control Cabinet/Packaged Electric And Electronic Control Compartment (Peecc)
Ex-2000 Exciter And Voltage Regulator
Generator Air Cooling System
Generator Protective Relays And Metering System
Instrumentation And Controls
Lube Oil Unit (Complete With Pumps And Heat Exchanger) And Hydraulic System
Dry Low No. Combustion System For Natural Gas Fuel: Natural Gas: 9 Ppmvd No,, @ 15%02
Fuel Metering System
Inlet Air Filter, Inlet Ducting, Silencing (Stainless Steel Perforated Sheet) And Supports
Optional Provisions For Inlet Chilling And Inlet System With Coatings And Materials For
High Humidity Environments
Turbine Exhaust Plenum Expansion Joint (Right Hand), And Enclosure
On-Line And Off-Line Compressor Water Wash System
One (1) Off-Base Water Wash Skid (One Per Site)
Provisions For Customer Supplied Open Cooling System
Electric Motor Starting System
Rotor Turning System
Gas Turbine Mark V Tm Control System
Peak Firing Capability
Ac Electrical Motor Control Center(S) Mounted In Peecc
Battery And Dual I 00% Chargers
Dc Electrical Motor Control Center(S) Mounted In Peecc
Fire Detection And C02 Supply Systems
Seller's Standard Installation Maintenance Tools Set (One (1) Per Site)
Seller Shall Provide Drawings And Other Engineering Data; Seller's Field Services,
Instruction Manuals, Recommended Spare Parts List, And Miscellaneous Materials
And Services, And Shall Participate In Design Conferences, As Required.
Miscellaneous Materials And Services
Miscellaneous Materials And Services Not Otherwise Specifically Called For Shall Be
Furnished By Seller In Accordance With The Following:
A. Piping Integral To Major Rotating Equipment Compartments Furnished Under These
B. Purchase Specifications, Except As Otherwise Specified.
B. Connections For The Purchaser's Piping And Instruments.
Seller's Standard Scope Of Supply For Instrument, Power And Control Wiring, And
Raceways Integral To Any Equipment Furnished Under These Specifications. This Shall
Include Terminal Blocks And Internal Wiring To These Terminal Blocks For Equipment
Requiring External Connection.
Coupling Guards For All Couplings.
Instruction Book Including Drawings Prints Information, Instructions, And Other Data
In Vendor Standard Electronic Or Hard Copy Format.
Detailed Storage Requirements And Lubrication Requirements (Including Frequencies)
For Use By The Purchaser's Erection Contractor.
Inventory At The Delivery Point, As Defined In The Purchase Contract.
Operating And Maintenance Manuals.
Commissioning Requirements Including Seller's Ftmction Tests.
Technical Direction Of Installation (Tdi).
Gas Turbine Control Interfaces To Plant Control System, (Plc Based)
Work Not Included Under These Specifications
The Following Items Of Work Will Be Furnished Or Caused To Be Furnished By
Purchaser:
A. Flashing Between Major Compartment By Others
B. Field Erection Of All Equipment At The Site.
Motor Controls And Starters Not Otherwise Specified To Be Furnished Under These
Purchase Specifications.
Foundations Including Embedment.
Grouting Materials And The Placing Thereof
Permanent Electric Wiring To Connect Equipment Terminal Boxes To The Plant Electrical
System, Interconnection Of Off-Base Components.
Lubricants And Fuels For Operation
Solvents And Cleaning Materials.
Finish Painting Of All Equipment Except As Specified Herein.
Operating Personnel For Start-Up And Tests.
Interconnecting Piping Between Rotating Equipment Skids And Off-Base Equipment.