PRODUCT INFORMATION
STPR1c 80µ
STPR1c 80 Film
Standard Thickness: 80 Microns
Description
: STPR1c 80 films are special structure Linear Low Density Polyethylene film
designed for sealing layer.
Features
: # Good clarity
# Good sealing strength
# High impact
# High Stiffness
Treatment
: Available one side
PROPERTIES
Mechanical
Tensile Strength
MD
TD
Elongation
MD
TD
SIT
P = 1,5 bar, t = 0,5 s
Seal Strength
Temp = 125oC
P = 1,5 bar, t = 0,5 s
Physical
Coefficient of Friction
Density
Miscellaneous
Surface Tension
UNIT
TESTING METHOD
TYPICAL VALUES
Kg/cm2
ASTM D882
%
ASTM D882
807
914
o
C
ASTM D882
115
g/15mm
ASTM F 88
1621
g/cm3
ASTM D1894
-
0.524
0,925
dyne/cm2
-
352
347
42
This information is give as guidelines and as product specifications. However the product
performance and it’s suitability for the purpose depend on the particular condition of use and the
material being laminated. User should confirm result by their own test.
This film is made from prime grade raw materials which comply with regulation 21 CFR 1771520 by
the FDA. This section refers to plastics for contact with food application.
Jl. Beringin F 12 No. 1A, Delta Silicon 2, Lippo Cikarang
Bekasi – Jawa Barat, Indonesia
PRODUCT INFORMATION
STPR1c 85µ
STPR1c 85 Film
Standard Thickness: 85 Microns
Description
: STPR1c 85 films are special structure Linear Low Density Polyethylene film
designed for sealing layer.
Features
: # Good clarity
# Good sealing strength
# High impact
# High Stiffness
Treatment
: Available one side
PROPERTIES
Mechanical
Tensile Strength
MD
TD
Elongation
MD
TD
SIT
P = 1,5 bar, t = 0,5 s
Seal Strength
Temp = 120oC
P = 1,5 bar, t = 0,5 s
Physical
Coefficient of Friction
Density
Miscellaneous
Surface Tension
UNIT
TESTING METHOD
TYPICAL VALUES
Kg/cm2
ASTM D882
%
ASTM D882
630
787
o
C
ASTM D882
100
g/15mm
ASTM F 88
1685
g/cm3
ASTM D1894
-
0.321
0,925
dyne/cm2
-
270
315
42
This information is give as guidelines and as product specifications. However the product
performance and it’s suitability for the purpose depend on the particular condition of use and the
material being laminated. User should confirm result by their own test.
This film is made from prime grade raw materials which comply with regulation 21 CFR 1771520 by
the FDA. This section refers to plastics for contact with food application.
Jl. Beringin F 12 No. 1A, Delta Silicon 2, Lippo Cikarang
Bekasi – Jawa Barat, Indonesia
PRODUCT INFORMATION
STPR1c 120µ
STPR1c 120 Film
Standard Thickness: 120 Microns
Description
: STPR1c 120 films are special structure Linear Low Density Polyethylene film
designed for sealing layer.
Features
: # Good clarity
# Good sealing strength
# High impact
# High Stiffness
Treatment
: Available one side
PROPERTIES
Mechanical
Tensile Strength
MD
TD
Elongation
MD
TD
SIT
P = 1,5 bar, t = 0,5 s
Seal Strength
Temp = 120oC
P = 1,5 bar, t = 0,5 s
Physical
Coefficient of Friction
Density
Miscellaneous
Surface Tension
UNIT
TESTING METHOD
TYPICAL VALUES
Kg/cm2
ASTM D882
%
ASTM D882
960
1002
o
C
ASTM D882
100
g/Inch
ASTM F 88
5072
g/cm3
ASTM D1894
-
0,58
0,925
dyne/cm2
-
578
562
44
This information is give as guidelines and as product specifications. However the product
performance and it’s suitability for the purpose depend on the particular condition of use and the
material being laminated.
This film is made from prime grade raw materials which comply with regulation 21 CFR 1771520 by
the FDA. This section refer to plastics for contact with food application.
Jl. Beringin F 12 No. 1A, Delta Silicon 2, Lippo Cikarang
Bekasi – Jawa Barat, Indonesia
PRODUCT INFORMATION
STPR1c 130µ
STPR1c 130 Film
Standard Thickness: 130 Microns
Description
: STPR1c 130 films are special structure Linear Low Density Polyethylene film
designed for sealing layer.
Features
: # Good clarity
# Good sealing strength
# High impact
# High Stiffness
Treatment
: Available one side
PROPERTIES
Mechanical
Tensile Strength
MD
TD
Elongation
MD
TD
SIT
P = 1,5 bar, t = 0,5 s
Seal Strength
Temp = 130oC
P = 1,5 bar, t = 0,5 s
Physical
Coefficient of Friction
Density
Miscellaneous
Surface Tension
UNIT
TESTING METHOD
TYPICAL VALUES
Kg/cm2
ASTM D882
%
ASTM D882
944
988
o
C
ASTM D882
110
g/15mm
ASTM F 88
2494
g/cm3
ASTM D1894
-
0.581
0,925
dyne/cm2
-
413
376
42
This information is give as guidelines and as product specifications. However the product
performance and it’s suitability for the purpose depend on the particular condition of use and the
material being laminated. User should confirm result by their own test.
This film is made from prime grade raw materials which comply with regulation 21 CFR 1771520 by
the FDA. This section refers to plastics for contact with food application.
Jl. Beringin F 12 No. 1A, Delta Silicon 2, Lippo Cikarang
Bekasi – Jawa Barat, Indonesia
PRODUCT INFORMATION
STPR1c 140µ
STPR1c 140 Film
Standard Thickness: 140 Microns
Description
: STPR1c 140 films are special structure Linear Low Density Polyethylene film
designed for sealing layer.
Features
: # Good clarity
# Good sealing strength
# High impact
# High Stiffness
Treatment
: Available one side
PROPERTIES
Mechanical
Tensile Strength
MD
TD
Elongation
MD
TD
SIT
P = 1,5 bar, t = 0,5 s
Seal Strength
Temp = 135oC
P = 1,5 bar, t = 0,5 s
Physical
Coefficient of Friction
Density
Miscellaneous
Surface Tension
UNIT
TESTING METHOD
TYPICAL VALUES
Kg/cm2
ASTM D882
%
ASTM D882
928
902
o
C
ASTM D882
115
g/15mm
ASTM F 88
2509
g/cm3
ASTM D1894
-
0.508
0,925
dyne/cm2
-
332
358
40
This information is give as guidelines and as product specifications. However the product
performance and it’s suitability for the purpose depend on the particular condition of use and the
material being laminated. User should confirm result by their own test.
This film is made from prime grade raw materials which comply with regulation 21 CFR 1771520 by
the FDA. This section refers to plastics for contact with food application.
Jl. Beringin F 12 No. 1A, Delta Silicon 2, Lippo Cikarang
Bekasi – Jawa Barat, Indonesia