【Normal Startup Procedure】
Move the Throttle
Connect the battery
Stick to bottom position pack to the ESC a
and then switch on your special tone"♪123"
Transmitter.
sounds, it means the
battery supply is OK.
【Throttle Range Setting】
Connect battery
Switch on the
Transmitter,and
pack to the
ESC a special
then move the
throttle stick to
tone"♪123"
top position.
sounds, that
means the battery
supply is OK.
Several "Beep" tones
sound to represent the
number of lipo cells.
As soon as the self test
process is finished a
"Beep" sound will be
emitted.
Wait for 2
seconds, "BeepBeep" tone sounds
,that means the
highest point of
throttle range has
been confirmed
Now you have control of
the motor with the
throttle stick.
You may go fly.
Move throttle
stick to the bottom
position, several
"Beep" tones
emits to represent
the number of
lipo cells.
A long "Beep"
sounds ,it means
the lowest
position throttle
range been
confirmed.
【Program the ESC with the transmitter】
 Enter program mode
Connect the battery
Switch on the
transmitter, move the
pack to the ESC, a
throttle stick to the top special tone "♪123"
position.
sounds, that means the
battery supply is OK.
Wait for 2 seconds, the
motor will emit "BeepBeep" tones.
Wait for another 5
seconds, special tone
"♪56712" sounds, that
means the
programming mode is
entered.
 Select programmable items
After entering programming mode ,you will hear 14 groups of "Beep" tones in a loop with the following
sequence ,If you move the throttle stick to bottom position within 3 seconds after one kind of tones,
the corresponding item will be selected.
Option
Item
Tones
1
Brake
1 short
2
Battery Type
2 short
3
Cutoff Mode
3 short
4
Cutoff Threshold
4 short
5
Start mode
1 long
6
Timing
1 long, 1 short
7
Governor Mode
1 long, 2 short
8
Motor Type
1 long, 3 short
9
PWM Frequency
1 long, 4 short
10
Built-in BEC Output
2 long
11
Motor Load
2 long, 1 short
12
Number of Cells
2 long, 2 short
13
Reset All To Default
3 long, 1 short
14
Exit
3 long, 2 short

Set item's value(Programmable value)
You will hear several "Beep" tones in a loop. Set the value matching to a tone by moving the throttle
stick to top position when you hear the tone, a special tone "♪1515" will sound, that means the value is
set and saved.(Keep the throttle stick at the top position). You will go back to Step #2 and you can
select other items. Or Move the throttle stick to bottom position within 2 seconds to exit program
mode directly).
Beeps
1 short
2 short
3 short
4 short
1 long
1 long
1 long
1 long
1 short
2 short 3 short
Item
Brake
*Off
Soft
Hard
Very
hard
Battery Type *Lipo
Ni MH
Cutoff Mode
Cutoff
Threshold
Start mode
Timing
Governor
Mode
Motor Type
PWM
Frequency
SBEC
Output
Motor Load
Lipo Cells
*Soft
Cut
Low
Hard
Cut
*Middle
*Normal
0°
*Off
*Normal
Motor
*12KHz
Soft
3.75°
Governor
Low
Special
Motor 1
24KHz
*5.25V
6V
*Normal
Heavy
*Auto
*Auto
High
Custom
Very soft
7.5°
11.25°
Governor
High
Special
Motor 2
*15°
18.75°
22.5°
For normal ESC
(2 to 6S Lipo)
For normal ESC
(5 to 12S Lipo)
Auto
2S
Very
Heavy
3S
4S
5S
6S
5S
6S
5S
10S
12S
26.25°
The value with *symbol is the default value
 Exit programming mode
There are 2 ways to exit
In Step 3,after
the programming mode.
special tone "♪1515", move
the throttle stick to the
bottom position within 2
seconds.
In Step 2, after
the Item 14 tones move the
throttle stick to the bottom
position.