The sprightly Cessna 150 is one of the most popular sport-trainers in the world. Introduced in 1957, a
total of 23, 836 examples were built before the model was replaced in 1977 by the similar, but more
powerful Cessna Model 152. With a low operating cost, it is also one of the easiest planes to fly and
remains popular with flying schools and clubs.
The Models A150L and K Aerobat are fully aerobatic and are stressed for load factors of +6g and -3g at
a full gross weight of 1,600 lbs. Powered by a 100hp Continental O-200 flat-four engine, its maximum
speed is 162 mph, with a 122 mph cruising speed at 7,000 feet. Maximum ceiling is 12, 650 feet.
39
Right Lower Wing
40 41
37
Support
38
42
Right Fuselage Half
1
2
Stand Base
3
4
Left Fuselage Half
5
18
6
19
21
20
22
8
7
9
24
25
23
27
26
10
13
11
12
14
15
16
29
17
28
32
30
31
33
34
35
36
Left Lower Wing
Upper Wing
Cement
Coller
Kleben
Pegar
Incollare
Colar
Kleven
1
DO NOT Cement
Ne pas Coller
Nicht Kleben
No Pegar
Non Incollare
Nao Colar
Niet Kleven
Cut away
Couper
Scheiden
Cortar
Tagliere
Cortar
Snijden
Optional parts
Choix
Auswahlmoglichkeit
Eleccion
Scelta
Opaco
Keuze
Repeat operation
Répeeter l' opération
Vorgang wiederholen
Repitir la operacion
Ripetere
Repitir a operaçao
Herhalen
2
COCKPIT ASSEMBLY
Symmetrical assembly
Drill hole
LANDING GEAR ASSEMBLY
13
All Parts
All Parts
4
16
8
17
23
19
14
15
18
7
• Cockpit floor BLACK
• Seats DARK and LIGHT GRAY
• Rudder pedals (23) ALUMINUM
3
• Firewall (8) BLACK
• Tires BLACK-GRAY
• Strut ALUMINUM
FUSELAGE ASSEMBLY
• Seat back (5) DARK and LIGHT GRAY
• Interior LIGHT GRAY
• Instrument panel BLACK-GRAY
with SILVER and BLACK details
• Control wheels BLACK
All Parts
9
Right fuselage half
41
34
34
5
5
42
Left fuselage half
4
NOSE GEAR AND STABILATOR MOUNTING, WING ASSEMBLY
40
29
IMPORTANT NOTE!
Fuselage stripe decals 1/3 must be applied before
mounting stabilators 28/29.
Refer to Paint & Decal Guide.
All Parts
28
37
37
Right lower
wing
Upper wing
38
36
Left lower
wing
5
WINGS, STRUTS AND WINDSHIELD MOUNTING
All Parts
30
39
31
6
ENGINE ASSEMBLY
All Parts
21
24
6
33
22
32
26
35
7
ENGINE / LOWER COWL INSTALLATION
All Parts
1
• Cowl interior ALUMINUM
25
• Engine mount (24) BLACK
• Engine accessories (6) , block (32/33) GUNMETAL
• Carburator (35) BLACK
• Cylinders (21/22) BLACK-GRAY
• Exhousts (25/26) BURNT METAL
8
FINAL ASSEMBLY / OPTIONAL STAND
All Parts
10
Support
12
11
Stand Base
3
20
2
27
• Cowl part interiors
ALUMINUM
White Navigation Light
3
Red Wingtip Light
4
Registration Number
Red Navigation Beacon
Green Wingtip Light
1
Registration Number
9 (Right side)
8 (Left side)
8 (Left side)
9 (Right side)
5
(Wrap around wingtip)
2
7 (Right side)
6 (Left side)
5
(Wrap around wingtip)
Aircraft is overall White. Apply decals 3/6 BEFORE installing
stabilizers. Black propeller blades, Silver spinner.
#11608
© 1/2008 MINICRAFT MODELS INC.
1501 Commerce Drive Elgin, IL 60123
www.minicraftmodels.com
Your Minicraft model includes high-quality waterslide decals. These decals adhere best
to a glossy surface; and it is recommended that you apply a clear gloss coat over your
painted model.
Use a sharp scissors or knife to cut individual decals from the carrier sheet. Do not cut
into the clear film surrounding the individual decals.
* It is recommended that you apply one decal at a time.
* Place the decal section in warm water, when first inserted in the water your decal will
curl, after approximately ten seconds the decal will uncurl. Remove from water and lay
on a paper towel. After approximately 10 - 20 seconds the decal will slide freely from the
backing paper. Use a small brush to help slide the decal from the backing paper and into
position on the model. Carefully blot excess water from the decal, using care not to move
the decal or tear it.
* If you choose to use a setting solution, apply a thin coat over the decal following the
manufacturer’s instruction.
* Allow the decal to dry overnight. Wash any adhesive residue off the model with a small
amount of clean water and dry thoroughly.
* Apply clear gloss, matte or flat coat to seal decals following the instructions from the
manufacturer.
Visit our Websitewww.minicraftmodels.com
Minicraft Models
1501 Commerce Drive
Elgin, IL 60123
Phone: 847-429-9676