TUESDAY
16 AUGUST 2016
Spectrum, Level 3A
Connexion@Nexus
Bangsar South City
FULLY
SUBSIDISED
for 30 SMEs
on first-come
first-serve basis.
Companies can also claim
from the SMETAP Scheme.
Supported by
Organised by
In collaboration with
SEMINAR ON
EFFECTIVE TEMPERING FOR MOULDS
Customer demands for higher quality, greater variety and lower costs
have placed pressure on plastics manufacturers to improve efficiency.
These multiple pressures have created the need for a knowledgeable
and skilled workforce who would be able to optimise and create
solutions to production problems as well as bring a greater level of
innovation to manufacturing.
This Seminar is beneficial to the plastics industry as it would assist
SMEs improve product/part quality, reduce production cycle time and
achieve greater profits.
The Seminar also highlights practical tips on cleaning and maintaining
moulds to achieve faster cooling time. Participants will learn the
following techniques:
i. To select a suitable type of cooling solution for the factory.
ii. To optimise mould cooling using infra rate analysis, flow and
temperature measurement.
iii. How to properly clean, maintain and manage cooling in moulds so
as to ensure mould efficiency required to produce consistent,
profitable parts.
iv. To use special technology such as variothermal control and
computer-aided design to systematically simulate mould
temperature and hot spots as well as cooling efficiency and time.
v. To uncover issues with existing moulds through a development of
best practices.
TENTATIVE PROGRAMME
TUESDAY
16 AUGUST 2016
REGISTRATION INFORMATION
Submission Deadline: Friday, 5 August 2016
CONFERENCE REGISTRATION FEES – RM800
(inclusive of 6% GST)
For Human Resource Development Fund (HRDF)
Contributors
• The Conference is FULLY SUBSIDISED for the first 30 SMEs
on a first-come first-serve basis.
• Companies can also claim under the SMETAP Scheme
(direct debit from employers’ levy balance).
• Companies interested to take advantage of the
Incentive/SMETAP Scheme are required to complete the
registration online at www.hrdf.com.my.
• Companies that do not wish to utilse their employers’ levy
balance are advised to remit payment via cheque to ‘MPMA’.
For Cash/Cheque Payments
Please fax/mail to:
Malaysian Plastics Manufacturers Association (MPMA)
37, Jalan 20/14, Paramount Garden, 46300 Petaling Jaya, Selangor, Malaysia
Tel: 03-7876 3027 Fax: 03-7876 8352
Contact: Ms Malathy / Ms Jacqui Sin
8.30 am
Registration
Name
9.00 am
Arrival of Guest-of-Honour
Designation
9.20 am
Welcome Address
Name
9.30 am
Keynote Address
Designation
9.40 am
Refreshments
10.00 am
Introduction to Effective Mould Tempering
Mr Anston Tan
German Training Centre of Injection Moulding
10.45 am
Measuring the Effectiveness of Cooling
Circuits
Ms Rachel Soh
Morglory International
11.30 am
Effective Ways to Clean and Treat Circuits
Mr Vladimir Shibayev
German Training Centre of Injection Moulding
12.15 pm
Using CAD to Optimise Mould Cooling
Ms Grace Liao
Moldex 3D
1.00 pm
Lunch
2.00 pm
Special Techniques: Variothermal Control
Mr Kurt Klopfenstein
HB-Therm-AG
2.45 pm
Cooling Plant Set-up
Mr Piergiorgio Coletto
Aquatech (A Piovan Company)
3.30 pm
Optimising Mould Cooling to Reduce Cycle
Time and Case Studies
Mr Bernd Johannson
German Training Centre for Injection Moulding
4.15 pm
4.30 pm
Name
Designation
Submitted by:
Name
Designation
Company
Address
Tel
Fax
Email
Cancellations/Refunds: A full refund will be made for cancellations by 5
August 2016.
Dress: Office Attire
HOTEL INFORMATION
MPMA has arranged for special discounted rates for all participants
at the following hotel:
VE HOTEL & RESIDENCE, BANGSAR SOUTH
8, Jalan Kerinchi, Bangsar South City, 59200 Kuala Lumpur, Malaysia.
Tel: (603) 2246 2888 Fax: (603) 2246 2999 PIC: Cik Azlin Zakaria
Closing Remarks
Room Types
Refreshments/End
Deluxe Room without Breakfast
Deluxe Room with Breakfast for Two
Daily Rates (MYR)
254.40 nett
286.20 nett