u
r
t
d
on,
ers.
Read and understand instructions completely before starting.
LinkingELECTRICAL SHOCK HAZARD
cate a selected menu.
PLUG-IN SWITCH MODULE
INSTALLATION GUIDE
High Voltage.
Thiscan
device
must and
be installed
by
Two or more compatible
devices
be linked
congured
a
quali
ed
installer
or
electrician.
Follow
all
to provide the desired control. There are two basic types of applicable
electrical codes
for installation.
devices in the system;
transmitters
and transceivers.
▪ Transmit-only: Transmitters are simple energy-harvesting
devices that send RF messages to communicate a condition,
level,the
or state.
Transmitters
canexample,
only be linked
to and
transceivers.
1. Turn
electrical
load on (for
a lamp)
unplug
Examples
> Self-powered
Light Switches, Occupancy Sensors
the
cord from
the wall outlet.
Transmit
& Receive:
Transceivers
2.▪ Plug
the cord
of the electrical
load,are
forcontrolling
example a devices
lamp, into
thatoutlet
send as
well
receive
RF messages. They also process
the
cord
ofas
the
module.
relevant control logic, and actuate the appropriate outputs
3. Plug the module into a standard wall outlet.
(switching a light on or off for example). Transceivers can be
4. Test
thewith
connection
by actuating
load
using the Set butlinked
transmitters
as well asthe
other
transceivers.
) on
the module
ton
(
Examples
>
Relays,
Gateways
NOTE:
The plug
and outlet
areispolarized,
and not intended to be
The Plug-in
Switch
Module
a Transceiver
mated
with &
non-polarized
(transmits
receives) devices.
To link the occupancy sensor to a transceiver; the transceiver
Optional
must rst Mounting
be powered, within wireless range of the controls it is
The
provides
a xed mounting option to
to bePlug-In
linked Switch
to, andModule
set to accepts
links.
prevent damage and theft. Using the included mounting plate,
Next, the desired transmitter, or another transceiver, is triggered
Plug-in
Switch
• Installation
mount the
deviceModule
high enough
off the oor Guide
to avoid spills and
to send a special link message. The awaiting transceiver receives
impact with cleaning equipment.
and stores the link permanently so the devices can interact to
provide
of intelligent
control
options.
1.
Usingaavariety
level and
a pencil, lightly
mark
two small dotsPage
to 1
align the upper edge of the module on the wall where you
want to mount it.
About
the
Setup
Interface provide sufficient clearance for
TIP: For
easy
housekeeping,
© 2013 EnOcean GmbH
The
setup interface
vacuum
cleaners. has two buttons, Menu and Set, that each
have a corresponding 3-color LED (green, amber, red). This sim2. Slide the mounting plate off the
ple interface is used to link and con gure devices as a system.
back of the module.
The buttons and LEDs are used to navigate and select linking
3. With the tab lock side down,
and setup options through a 3-tier menu system consisting of
mount the plate securely to the
different Modes > Menus > Options.
wall.
To use the interface, hold the module so both thumbs can click
Using the
pencil
marks tothe
ensure
level,
mark theand
theA.buttons
without
obscuring
LEDs.it’sThe
illustration
two
mounting
screw
drill
points.
legend below describe how the buttons are used and the meaningB.ofDrill
the two
LED holes
responses.
for the wall anchors with a 3/16” drill bit
insert
the wall
To exitand
from
anywhere
inanchors.
a menu, hold both buttons at the same
time
for
2
seconds.
C. Insert the first screw loosely and level the module.
D. Insert the second screw, and
then hand tighten the fi rst
screw.
4. Slide module onto the mounting
plate until it clicks in place.
NOTE: Any EnOcean-based switch
can be linked to the module.
Blink Legend
The Menu LED or Set LED display solid for a number of seconds in a certain color to indicate a mode or a con rmation.
Linking
The Menu LED blinks a number of times in a color to indi-
cate
a selected devices
menu. can be linked and congured
Two or more
compatible
to provide the
control.
There are
two basic
types
of
Thedesired
Set LED blinks
a number
of times
in a color
to indicate
devices in the
system;
transmitters
and
transceivers.
an option.
▪ Transmit-only:
are
simplethe
energy-harvesting
A numberTransmitters
in a white box
indicates
number of times to
devices that
send
RF messages
to communicate
a condition,
click the
Menu
button or Set
button.
level, or Astate.
Transmitters
can
only
be
linked
to
number in a black box indicates the numbertransceivers.
of seconds to
Examples
> Self-powered
Switches,
Occupancy Sensors
hold
down the MenuLight
button
or Set button.
▪ Transmit & Receive: Transceivers are controlling devices
send
as well as receive
messages. They also process
Tothat
link
a transmitter
to aRFtransceiver
The Set LED blinks a number of times in a color to indicate
an option.
A number in a white box indicates the number of times to
click the Menu button or Set button.
A number in a black box indicates the number of seconds to
hold down the Menu button or Set button.
To link a transmitter to a transceiver
1. Access Basic Setup mode.
NOTE: By default, the Accept Link option in the Linking
menu is selected. Once activated, this option stays active for
two minutes to provide time to link multiple devices.
Ready to accept links.
2. For the transmitter to be linked, do one of the following according to the type of device:
A. Sensor: click the designated link button.
B. Key Card Switch: insert/remove the card 3 times quickly.
C. Rocker Pad: click the top button 3 times quickly.
Device linked successfully.
Set LED displays solid
About green
the Setup
Interface
for 3 seconds.
Plug-in
• Installation
Guide
The
setup Switch
interfaceModule
has two buttons,
Menu and
Set, that each
have a corresponding
LED (green, amber, red). This simReady to accept3-color
new links.
ple interface is used to link and con gure devices as a system.
2
3. To exit mode and return to normal operation, press Page
and hold
The buttons and LEDs are used to navigate and select linking
both buttons for 2 seconds.
and setup options through a 3-tier menu system consisting of
different
Modes
> Menus > Options.
To unlink
a device
To
use the
hold
moduleinsothe
both
can click
Follow
theinterface,
same steps
asthe
described
“Tothumbs
link...” section
the
buttons
without
obscuring
the
LEDs.
The
illustration
and
above with the following deviations:
legend below describe how the buttons are used and the mean▪ After step 1 in the “To link...” section above, click the “Set”
ing of the LED responses.
(right) button 3 times to enable the “Remove Link” option.
To exit from anywhere in a menu, hold both buttons at the same
time Ready
for 2 seconds.
to remove links.
▪ Follow the same instructions as shown in Step 2 of the “To
link...” section. The Set (right) LED will turn red briefly to indicate the link was successfully removed.
To restore factory defaults
Follow these steps to clear all linked devices and restore the
Plug-in Switch Module to its factory default settings.
1. Press and hold both buttons for 15 seconds
>> Hold buttons until the Menu (left) LED is solid RED and
the Set (right) LED is solid Amber (Both LEDs will turn various
Blinkcolors
Legend
as the module cycles through the resetting process.
2. Press The
andMenu
hold LED
the or
SetSet
(right)
buttonsolid
for 3
toofconLED display
forseconds
a number
secfirm factory
reset.
onds in a certain color to indicate a mode or a conrmation.
3. DeviceThe
will
reboot
initiate
startofup
LEDinsequence.
Menu
LEDand
blinks
a number
times
a color to indicate a selected menu.
Con
guring
The Set
LED blinks a number of times in a color to indicate
an option.
The default
settings on the module support common control
scenarios.AHowever,
settings
can be
number insome
a whiteoccupancy
box indicates
the number
of adjusted
times to
on the module
using
the
setup
interface,
if
required.
click the Menu button or Set button.
black box indicates
the number of seconds to
Application
Setting A number in a Default
hold down the Menu button or Set button.
Control
& Design
AutomaticallyLighting
If linked to
an occupancy
sen9144
Deering Ave.,
Chatsworth,
CA 91311
Determined
sor, the
default is Enabled.
Auto-On
To link a transmitter to a transceiver
www.lightingcontrols.com
If linked to a switch, the default
2014 Acuity Brands Lighting Inc., All rights reserved
1. Access Basic Setup ©mode.
is Disabled for manual control.
5 minutes
linked to a occupancy senor
Vacancy
Check
NOTE: By
default, the
Accept Link Ifoption
in the Linking
To
Th
De
1.
2.
3.
4.
A
Th
on
fa
th
m
Fr
th
by
on
in
Cl
pr
an
To
Th
m
1.
2.