I n s ta l l at i o n I n s t r u c t i o n s
Bionic™ 4 — Standard/Continuous X1, X2, X6
5˝
5"
5"
5˝
6-1/2˝
61 2"
5 "1
5/2˝
1
2
1"
11 16"
4-4 3/"32˝
6"
6˝
1
4- /32˝
6˝
31
4
16
T-bar
Flush SPL Louver (shown)
Regressed Lens
1) Identify housing:
Parts shipped separately
Start/End units are capped on one end
Intermediate units are not capped
Individual units are capped on both ends.
.437
2.562
END VIEW
SCALE 1 : 1
75°
Reflectors
.250
.187 X .375 SLOT
16"
6"
X1, X2 or X6 trim (X2/X6 shown)
Lens
Scale
Drawing Size
B
VAULT
Sheet
FRONT VIEW
SCALE 1 : 1
X3/X7 Start/End Unit
Date
Date
Appr
Date
Of
X1
Star
Project
Description
Finish
1.000
Prudential LTG.
Drawn By
Check
Material
Rev
Part Number
SCALE 1 : 1
R.125 (TYP.) PICTORIAL VIEW
1774 East 21st Street, Los Angeles, CA 90058
www.prulite.com
Aligner Splines
Adjustable Hanger
Bracket
T Bar Bracket
X1/X2/X6
X1Start/End
Start/End/
Unit
Individual
X3/X7 Start/End Unit
REV
Sca
Drawing Size
B
Sh
Lens Removal Tool
Intermediate Unit
Intermediate
8-32x3/8˝ Self-tapping
Machine Screws
Fin
Prudential LTG.
Ma
1774 East 21st Street, Los
www.prulite
Notes:
1. Housing ships separated from gear tray, reflectors and lens
for easy installation. (gear tray for STG only)
2. Remove specular reflector protective coating (if required)
3. Install lamps (by others)
WARNING: Ground fixture in accordance with local and national electrical
codes. Failure to do so may result in serious personal injury.
We reserve
change details of design,
REV the right to
DESCRIPTION
DATE materials
REV. BY and finish in any
REVISION HISTORY
way that will
not alterVAULT
installed appearance or reduce function or performance.
B
All hardware shipped in bulk.
Scale
Drawing Size
Sheet
Drawn By
Date
Check
Date
Appr
Date
Of
Intermediate Unit
Finish
Prudential LTG.
Project
Description
Material
Rev
Part Number
1774 East 21st Street, Los Angeles, CA 90058
www.prulite.com
Page 1 of 4, Jan-13
1774 East 21st Street, Los Angeles, CA 90058 • 213-746-0360 • www.prulite.com
or wire from
adjustable
hanger bracket
I n s ta l l at i o n I n s t r u c t i o n s
Bionic™ 4 — Standard/Continuous X1, X2, X6
www.prulite.com
1774 East 21st Street, Los Angeles, CA 90058
Prudential LTG.
Part Number
Rev
Material
Appr
Finish
Date
Description
Of
Check
VAULT
B
Drawing Size
Scale
8-32 x 3/8"
SELF-TAPPING
MACHINE SCREW
Drawn By
Date
Date
Project
8-32 x 1/4"
MACHINE SCREW
5) Secure luminaire to structure
(multiple options).
4) Install ‘U’ shaped end &
straight trim.
U-SHAPED TRIM
INSTALL
3) Install Aligner Splines
on housing.
Two at every joint on - outside or inside housing with
#8 screws – finger snug.
Sheet
2) Remove Shipping Straps.
Note: 6´ or smaller units have framed trims
– install NOW!
Top view of Option A Installation hole spacing
X
Y
1/4-20 all-thread
can protrude
into housing no
more than 3/8˝.
Y
X= 2´
Y = 9˝ from center hole
X= 3´
Y = 15˝
X= 4´
Y = 21˝
X= 5´
Y = 27˝
X= 6´
Y = 33˝
X= 7´
Y = 39˝
X= 8´
Y = 45˝
Safety Strap
Page 2 of 4, Jan-13
1774 East 21st Street, Los Angeles, CA 90058 • 213-746-0360 • www.prulite.com
I n s ta l l at i o n I n s t r u c t i o n s
Bionic™ 4 — Standard/Continuous X1, X2, X6
6) If additional holes are drilled in top plate
for 1/4-20 all thread, support with
additional #8 screws at closest location
to new holes.
7) Fasten Inside Joiner Brackets.
WARNING! Failure
to properly install
top plate screws
will void warranty.
8-32 x 3/8” self-tapping
machine screw
8-32 x 1/4” machine
screws (by others)
8) Slide & tighten Aligner Splines over joints.
9) Snap “Gear Trays” into housing (where
required) - Plug Quick Connects as you
install each Gear Tray.
10) Swing Safety Brackets and secure.
11) Install reflectors.
Gear Tray
8-32x1/4” screws
WARNING! Failure to properly install
Safety Brackets will void warranty.
Use filler reflector as needed, at end of
rows - trim to fit.
Page 3of 4, Jan-13
1774 East 21st Street, Los Angeles, CA 90058 • 213-746-0360 • www.prulite.com
I n s ta l l at i o n I n s t r u c t i o n s
Bionic™ 4 — Standard/Continuous X1, X2, X6
12) Install lamps (by others).
13) Install lensing, cut last piece to fit.
Note: Leave 1/16˝ air gap at each end of run
Table saw or chop saw with a 80T blade recommended.
Page 4 of 4, Jan-13
1774 East 21st Street, Los Angeles, CA 90058 • 213-746-0360 • www.prulite.com