COMMERCIAL IN CONFIDENCE
AUTHORITY: The Secretary of State for the
Home Department
acting through Border Force
VOLUME 3
SCHEDULE 1 – STATEMENT OF
REQUIREMENTS, PART C
APPENDIX 1: LIST OF CCTV CAMERA
SPECIFICATIONS
PROVISION AND INSTALLATION OF CCTV AT
THE PORT OF DOVER
SEPTEMBER 2013
Provision and Installation of CCTV at the Port of Dover
1
IMO 13 250/2
Volume 3 – Statement of Requirements, Part C – Appendix 1: List of Camera Specifications.Final.September2013
COMMERCIAL IN CONFIDENCE
Camera Type C1 - Indoor Standard Definition IP


Image capture
Image sensor type:
Sensitivity @ f1.2:



Lens:
Iris:
Shutter:
1/3" CCD
0.3 lux Colour,Down to 0.012 lux (Low light technology)
Minimum illumination (30IRE)
2.8-10mm (or 9-22mm) - As required
Automatic iris control
Auto (1/50 to 1/50000) automatic flickerless, fixed selectable




Image processing
Processing system:
Gain control:
White balance:
Dynamic range:
Digital signal processing (DSP)
20 dB (max)
ATW, ATWHold (2500 to 10000K)
60 dB (10bit-processing) - Minimum (or to suit specific requirements)






Digital video output
Colour system:
Compression:
Image resolution (Hor x Vert):
Frame rate:
Signal to noise ratio:
Video output connector:

Protocols:

Audio
Line in / Line out:
1 x mono line in, 1 x mono line out

Alarm
Alarm input signal:
1 non-isolated closing contact, 1 relay output



Enclosure and mounting
Enclosure type:
Enclosure application:
Mounting:







Camera movements
Video latency:
Pan range and speed:
Pan speed:
Tilt range:
Tilt speed:
Position presets:
Position preset activation:




Intelligence
Video motion detection:
Object detection:
Privacy zone masking:
Anti-tamper:

Alarm-triggered refresh rate:
Yes, Motion
Minimum object size
Four independent areas, fully programmable
Global change, scene too bright, scene too dark, scene too noisy,
reference check
Via Alarm input/ Motion/Audio alarm / Video loss alarm‑

Power supply:
Power-over-Ethernet

Ambient conditions:
Minus 50 degrees to + 50 degrees (with heater on)
Colour / Low light technology (Auto, forced)
H.264 (ISO/IEC 14496-10); M-JPEG, JPEG
4CIF 704 x 576,
Adjustable up to 25 images per second
>50 dB with AGC off
STP, 10/100 Base-T, auto-sensing, half/full duplex, RJ45
2.5mm jack 75 Ohm, Analogue Composite for service
RTP, Telnet, UDP, TCP, IP, HTTP, HTTPS, FTP, DHCP,
IGMP V2/V3, ICMP, ARP, SMTP, SNTP, SNMP, 802.1x, PnP
Mini-dome
IP 66 and NEMA‑4X
Recessed mount, surface mount, pendant wall mount, corner
mount, pipe mount – As required
Min 120ms, Max 240ms
N/A
N/A
N/A
N/A
N/A
N/A
Provision and Installation of CCTV at the Port of Dover
2
IMO 13 250/2
Volume 3 – Statement of Requirements, Part C – Appendix 1: List of Camera Specifications.Final.September2013
COMMERCIAL IN CONFIDENCE
Camera Type C2 - Internal High Definition IP





Image capture
Image sensor type:
Sensitivity @ f1.2:
Lens:
Iris:
Shutter:
1/2.7" CMOS
0.22 lux Colour, 0.05 lux Mono Minimum illumination (30IRE)
3.8-13mm (or: 1.8-3mm; 9-40mm) - As required
Automatic iris control
Auto (1/50 to 1/150000) automatic. Fixed selectable





Image processing
Processing system:
Backlight compensation:
White balance:
Contrast enhancement:
Dynamic range:
Digital signal processing (DSP)
On/off
ATW (2500 to 10000K), ATWhold and manual
On/off
Digital WDR: 76dB - Minimum (or to suit specific requirements)







Digital video output
Colour system:
Compression:
Image resolution (Hor x Vert):
Frame rate:
Signal to noise ratio:
Video output connector:
Protocols:

Audio
Line in / Line out:
1 x mono line in, 1 x mono line out

Alarm
Alarm input signal:
2 inputs, 1 relay output



Enclosure and mounting
Enclosure type:
Enclosure application:
Mounting:
Mini-dome
IP66, NEMA 4x
Surface mount, wall mount, pendant pipe mount - as required







Camera movements
Video latency:
Pan range and speed:
Pan speed:
Tilt range:
Tilt speed:
Position presets:
Position preset activation:
Min 120ms, Max 240ms
N/A
N/A
N/A
N/A
N/A
N/A




Intelligence
Video motion detection:
Object detection:
Privacy zone masking:
Anti-tamper:

Alarm-triggered refresh rate:
Yes
Minimum object size
Four independent areas, fully programmable
Global change, scene too bright, scene too dark, scene too noisy,
reference check
Via Alarm input/ Motion/Audio alarm / Video loss alarm

Power supply:
Power-over-Ethernet

Ambient conditions:
Minus 50 degrees to + 55 degrees
Day/night - Colour, Mono, Auto
H.264 (ISO/IEC 14496-10); M-JPEG, JPEG - Quad steaming
1920 x 1080p, also capable of 720p, 480p, 240p
Adjustable up to 25 images per second
>50 dB
STP , 10/100 Base-T, auto-sensing, half/full duplex, RJ45
RTP, RTSP, Telnet, UDP, TCP, IP, HTTP, HTTPS, FTP, DHCP,
IGMP V2/V3, ICMP, ARP, SMTP, SNTP, SNMP, 802.1x, UPnP,
SNTP, SNMP, 802.1x, UPnP
Provision and Installation of CCTV at the Port of Dover
3
IMO 13 250/2
Volume 3 – Statement of Requirements, Part C – Appendix 1: List of Camera Specifications.Final.September2013
COMMERCIAL IN CONFIDENCE
Camera Type C3 - Internal Vandal Resistant Corner Mount IP





Image capture
Image sensor type:
Sensitivity @ f1.2:
Lens:
Iris:
Shutter:






Image processing
Processing system:
Gain control:
White balance:
Dynamic engine:
Dynamic range:
Peak White Invert:






Digital video output
Colour system:
Compression:
Image resolution (Hor x Vert):
Frame rate:
Signal to noise ratio:
Video output connector:

Protocols:

Audio
Line in / line out:
N/A

Alarm
Alarm input signal:
1 non-isolated closing contact, 1 relay output



Enclosure and mounting
Enclosure type:
Enclosure application:
Mounting:
Vandal resistant corner mount c/w 1/4" lexan windows
IP 66 and NEMA‑4X
corner mount







Camera movements
Video latency:
Pan range and speed:
Pan speed:
Tilt range:
Tilt speed:
Position presets:
Position preset activation:
Min 120ms, Max 240ms
N/A
N/A
N/A
N/A
N/A
N/A




Intelligence
Video motion detection:
Object detection:
Privacy zone masking:
Anti-tamper:

Alarm-triggered refresh rate:
Yes
Minimum object size
N/A
Global change, scene too bright, scene too dark, scene too noisy, reference
check
Via Alarm input/ Motion/Audio alarm / Video loss alarm

Power supply:
Power over Ethernet

Ambient conditions:
Minus 50 degrees to + 50 degrees (with heater on)
1/3" CCD, Hi-Resolution Colour
2.7 Lux at F1.4
Fixed 2.5mm wide angle providing 88o Horizontal FoV and 72o Vertical FoV
Auto (1/50 to 1/10000) selectable. Auto (1/50 to 1/50000) automatic
flickerless, fixed selectable
Digital signal processing (DSP)
AGC On or Off (0-30dB) selectable
ATW, ATWHold (2500 to 10000K)
2X-Dynamic, XF-Dynamic, Smart BLC+2X-Dynamic
120 dB (20-bit image processing)
On/Off
Colour
H.264 (ISO/IEC 14496-10); M-JPEG, JPEG
4CIF 704 x 576,
Adjustable up to 25 images per second
>48 dB
STP, 10/100 Base-T, auto-sensing, half/full duplex, RJ45. 2.5mm jack 75
Ohm, Analogue Composite for service only
RTP, Telnet, UDP, TCP, IP, HTTP, HTTPS, FTP, DHCP, IGMP V2/V3,
ICMP, ARP, SMTP, SNTP, SNMP, 802.1x, UPnP
Provision and Installation of CCTV at the Port of Dover
4
IMO 13 250/2
Volume 3 – Statement of Requirements, Part C – Appendix 1: List of Camera Specifications.Final.September2013
COMMERCIAL IN CONFIDENCE
Camera Type C4 - External Standard Definition IP





Image capture
Image sensor type:
Sensitivity @ f1.2:
Lens:
Iris:
Shutter:






Image processing
Processing system:
Gain control:
White balance:
Dynamic engine:
Dynamic range:
Peak White Invert:






Digital video output
Colour system:
Compression:
Image resolution (Hor x Vert):
Frame rate:
Signal to noise ratio:
Video output connector:

Protocols:

Audio
Line in / line out:
1 x mono line in, 1 x mono line out

Alarm
Alarm input signal:
1 non-isolated closing contact, 1 relay output



Enclosure and mounting
Enclosure type:
Enclosure application:
Mounting:







Camera movements
Video latency:
Pan range and speed:
Pan speed:
Tilt range:
Tilt speed:
Position presets:
Position preset activation:




Intelligence
Video motion detection:
Object detection:
Privacy zone masking:
Anti-tamper:

Alarm-triggered refresh rate:
Yes
Minimum object size
Four independent areas, fully programmable
Global change, scene too bright, scene too dark, scene too noisy, reference
check
Via Alarm input/ Motion/Audio alarm / Video loss alarm‑

Power supply:
Power-over-Ethernet

Ambient conditions:
Minus 50 degrees to + 50 degrees (with heater on)
1/3" CCD, WDR, dual shutter
0.28 lux Colour, 0.099 lux Mono Minimum illumination (30IRE) (SensUp off)
2.8-10mm IR corrected (or: 9-22mm; 6-50mm) - as required
Automatic iris control
Auto (1/50 to 1/10000) selectable. Auto (1/50 to 1/50000) automatic
flickerless, fixed selectable
Digital signal processing (DSP)
AGC On or Off (0-30dB) selectable
ATW, ATWHold (2500 to 10000K)
2X-Dynamic, XF-Dynamic, Smart BLC+2X-Dynamic
120 dB (20-bit image processing)
On/Off
Day/night - Colour, Mono, Auto
H.264 (ISO/IEC 14496-10); M-JPEG, JPEG
4CIF 704 x 576,
Adjustable up to 25 images per second
>50 dB
STP, 10/100 Base-T, auto-sensing, half/full duplex, RJ45. 2.5mm jack 75
Ohm, Analogue Composite for service only
RTP, Telnet, UDP, TCP, IP, HTTP, HTTPS, FTP, DHCP, IGMP V2/V3,
ICMP, ARP, SMTP, SNTP, SNMP, 802.1x, UPnP
Mini-dome
IP 66 and NEMA‑4X
Recessed mount, surface mount, pendant wall mount, corner mount, pipe
mount – as required
Min 120ms, Max 240ms
N/A
N/A
N/A
N/A
N/A
N/A
Provision and Installation of CCTV at the Port of Dover
5
IMO 13 250/2
Volume 3 – Statement of Requirements, Part C – Appendix 1: List of Camera Specifications.Final.September2013
COMMERCIAL IN CONFIDENCE
Camera Type C5 - External High Definition IP





Image capture
Image sensor type:
Sensitivity @ f1.2:
Lens:
Iris:
Shutter:
1/2.7" CMOS
0.22 lux Colour, 0.05 lux Mono Minimum illumination (30IRE)
3.8-13mm (or: 1.8-3mm; 9-40mm) - As required
Automatic iris control
Auto (1/50 to 1/150000) automatic. Fixed selectable





Image processing
Processing system:
Backlight compensation
White balance:
Contrast enhancement:
Dynamic range:
Digital signal processing (DSP)
On/off
ATW (2500 to 10000K), ATWhold and manual
On/off
Digital WDR: 76dB - minimum (or to suit specific requirements)







Digital video output
Colour system:
Compression:
Image resolution (Hor x Vert):
Frame rate:
Signal to noise ratio:
Video output connector:
Protocols:

Audio
Line in / Line out:
1 x mono line in, 1 x mono line out

Alarm
Alarm input signal:
2 inputs, 1 relay output



Enclosure and mounting
Enclosure type:
Enclosure application:
Mounting:
Mini-dome
IP66, NEMA 4x
Surface mount, wall mount, pendant pipe mount - as required







Camera movements
Video latency:
Pan range and speed:
Pan speed:
Tilt range:
Tilt speed:
Position presets:
Position preset activation:
Min 120ms, Max 240ms
N/A
N/A
N/A
N/A
N/A
N/A




Intelligence
Video motion detection:
Object detection:
Privacy zone masking:
Anti-tamper:

Alarm-triggered refresh rate:
Yes
Minimum object size
Four independent areas, fully programmable
Global change, scene too bright, scene too dark, scene too noisy, reference
check
Via Alarm input/ Motion/Audio alarm / Video loss alarm

Power supply:
Power-over-Ethernet

Ambient conditions:
Minus 50 degrees to + 55 degrees
Day/night - Colour, Mono, Auto
H.264 (ISO/IEC 14496-10); M-JPEG, JPEG - Quad steaming
1920 x 1080p, also capable of 720p, 480p, 240p
Adjustable up to 25 images per second
>50 dB
STP, 10/100 Base-T, auto-sensing, half/full duplex, RJ45
RTP, RTSP, Telnet, UDP, TCP, IP, HTTP, HTTPS, FTP, DHCP, IGMP
V2/V3, ICMP, ARP, SMTP, SNTP, SNMP, 802.1x, UPnP, SNTP, SNMP,
802.1x, UPnP
Provision and Installation of CCTV at the Port of Dover
6
IMO 13 250/2
Volume 3 – Statement of Requirements, Part C – Appendix 1: List of Camera Specifications.Final.September2013
COMMERCIAL IN CONFIDENCE
Camera Type C6 - External Standard Definition IP





Image capture
Image sensor type:
Sensitivity @ f1.2:
Lens:
Iris:
Shutter:






Image processing
Processing system:
Gain control:
White balance:
Dynamic engine:
Dynamic range:
Peak White Invert:






Digital video output
Colour system:
Compression:
Image resolution (Hor x Vert):
Frame rate:
Signal to noise ratio:
Video output connector:

Protocols:

Audio
Line in / line out:
1 x mono line in, 1 x mono line out

Alarm
Alarm input signal:
1 non-isolated closing contact, 1 relay output



Enclosure and mounting
Enclosure type:
Enclosure application:
Mounting:







Camera movements
Video latency:
Pan range and speed:
Pan speed:
Tilt range:
Tilt speed:
Position presets:
Position preset activation:




Intelligence
Video motion detection:
Object detection:
Privacy zone masking:
Anti-tamper:

Alarm-triggered refresh rate:
Yes
Minimum object size
Four independent areas, fully programmable
Global change, scene too bright, scene too dark, scene too noisy, reference
check
Via Alarm input/ Motion/Audio alarm / Video loss alarm

Power supply:
Power-over-Ethernet

Ambient conditions:
Minus 20 degrees to + 50 degrees
1/3" CCD, WDR, dual shutter
0.15 lux Colour, 0.060 lux Mono Minimum illumination (30IRE) (SensUp off)
2.8-6mm IR corrected (or: 2.8-11mm; 7.5-50mm)
Automatic iris control
Auto (1/50 to 1/10000) selectable. Auto (1/50 to 1/50000) automatic
flickerless, fixed selectable
Digital signal processing (DSP)
AGC On or Off (0-30dB) selectable
ATW, ATWHold (2500 to 10000K)
2X-Dynamic, XF-Dynamic, Smart BLC+2X-Dynamic
120 dB (20-bit image processing)
On/Off
Day/night - Colour, Mono, Auto
H.264 (ISO/IEC 14496-10); M-JPEG, JPEG
4CIF 704 x 576,
Adjustable up to 25 images per second
>50 dB
STP, 10/100 Base-T, auto-sensing, half/full duplex, RJ45. 2.5mm jack 75
Ohm, Analogue Composite for service only
RTP, Telnet, UDP, TCP, IP, HTTP, HTTPS, FTP, DHCP, IGMP V2/V3,
ICMP, ARP, SMTP, SNTP, SNMP, 802.1x, UPnP
Surface mount, pendant wall mount, corner mount,
External housing c/w wiper
Min 120ms, Max 240ms
N/A
N/A
N/A
N/A
N/A
N/A
Provision and Installation of CCTV at the Port of Dover
7
IMO 13 250/2
Volume 3 – Statement of Requirements, Part C – Appendix 1: List of Camera Specifications.Final.September2013
COMMERCIAL IN CONFIDENCE
Camera Type C7 - External High Definition IP





Image capture
Image sensor type:
Sensitivity @ f1.2:
Lens:
Iris:
Shutter:
1/3" CMOS HD
0.25 lux Colour, 0.08 lux Mono Minimum illumination (30IRE)
As required
Automatic iris control
Auto (1/50 to 1/150000) automatic. Fixed selectable





Image processing
Processing system:
Backlight compensation:
White balance:
Contrast enhancement:
Dynamic range:
Digital signal processing (DSP)
On/off
ATW (2500 to 10000K), ATWhold and manual
On/off
Digital WDR: 90dB







Digital video output
Colour system:
Compression:
Image resolution (Hor x Vert):
Frame rate:
Signal to noise ratio:
Video output connector:
Protocols:

Audio
Line in / Line out:
1 x mono line in, 1 x mono line out

Alarm
Alarm input signal:
2 inputs, 1 relay output



Enclosure and mounting
Enclosure type:
Enclosure application:
Mounting:







Camera movements
Video latency:
Pan range and speed:
Pan speed:
Tilt range:
Tilt speed:
Position presets:
Position preset activation:




Intelligence
Video motion detection:
Object detection:
Privacy zone masking:
Anti-tamper:

Alarm-triggered refresh rate:
Yes
Minimum object size
Four independent areas, fully programmable
Global change, scene too bright, scene too dark, scene too noisy, reference
check
Via Alarm input/ Motion/Audio alarm / Video loss alarm

Power supply:
Power-over-Ethernet

Ambient conditions:
Minus 20 degrees to + 50 degrees
Day/night - Colour, Mono, Auto
H.264 (ISO/IEC 14496-10); M-JPEG, JPEG - Quad steaming
1920 x 1080p,
Adjustable up to 25 images per second
>50 dB
STP, 10/100 Base-T, auto-sensing, half/full duplex, RJ45
RTP, RTSP, Telnet, UDP, TCP, IP, HTTP, HTTPS, FTP, DHCP, IGMP
V2/V3, ICMP, ARP, SMTP, SNTP, SNMP, 802.1x, UPnP, SNTP, SNMP,
802.1x, UPnP
Surface mount, pendant wall mount, corner mount,
External housing c/w wiper
Min 120ms, Max 240ms
N/A
N/A
N/A
N/A
N/A
N/A
Provision and Installation of CCTV at the Port of Dover
8
IMO 13 250/2
Volume 3 – Statement of Requirements, Part C – Appendix 1: List of Camera Specifications.Final.September2013
COMMERCIAL IN CONFIDENCE
Camera Type C8 - External Standard Definition PTZ





Image capture
Image sensor type:
Sensitivity @ f1.2:
Lens:
Iris:
Shutter:
1/4" ExView HAD CCD - Progressive Scan
0.66 lux Colour, 0.104 lux Mono Minimum illumination (30IRE) - SensUp Off
28 x zoom (3.5 - 98mm). F1.35 to F3.7
Automatic iris control with manual override
1/1 to 1/10,000 sec., 22 steps




Image processing
Processing system:
Gain control:
Dynamic range:
White balance:
Digital signal processing (DSP)
Auto/Manual/Max (-3dB to 28dB, 2dB steps)
128 dB
2000K to 10,000K







Digital video output
Colour system:
Compression:
Image resolution (Hor x Vert):
Frame rate:
Signal to noise ratio:
Video output connector:
Protocols:

Audio
Line in / out:
Via IP encoder

Alarm
Alarm input signal:
1 tamper input, 8 additional inputs with optional alarm card, 2 relay outputs

Enclosure and mounting
Enclosure type:


Enclosure application:
Mounting:




Camera movements
Video latency:
Pan range and speed:
Pan speed:
Tilt range:



Tilt speed:
Position presets:
Position preset accuracy:
N/a
360 degrees
0.2degrees/sec - 120degrees/sec
Upright unit, -58degress to +90 degrees,
Canted unit, -103 degrees to +90 degrees
0.2degrees/sec to 60degrees/second
99, each with 20 characters per title
0.17 degrees (typical)







Intelligence
Image stabilisation:
Video motion detection:
Object detection:
Privacy zone masking:
Anti-tamper:
Alarm-triggered refresh rate:
Lighting:
Yes
Via encoder
Via encoder
24 individually configurable
Tamper input alarm
Via encoder
Yellow' light compensation

Power supply:
24V, 115V, 230V

Ambient conditions:
Minus 40 degrees to + 60 degrees
Day/night - Colour, Mono
PAL - used in conjunction with IP encoder
752 x 582
Adjustable up to 25 images per second
>50 dB
Coaxial via composite cable
PTZ dome, cast solid aluminium, tempered flat glass with long-life silicone
wiper. 360degree continuous rotation
IP68 rated
Wall mount, corner mount, pole mount, column mount
Provision and Installation of CCTV at the Port of Dover
9
IMO 13 250/2
Volume 3 – Statement of Requirements, Part C – Appendix 1: List of Camera Specifications.Final.September2013
COMMERCIAL IN CONFIDENCE
Camera Type C9 - External Vehicle Capture




Image capture
Image sensor type:
IR Illumination
Operational Range
Max capture speed:
1/3" CCD,
Pulsed LED array
3.8m to 28.0m selected to suit final mounting position
140 mph



Image processing
Processing system:
Gain control:
Dynamic range:
Digital signal processing (DSP)
AGC On or Off (0-30dB) selectable
120 dB (20-bit image processing)






Digital video output
Colour system:
Compression:
Image resolution (Hor x Vert):
Frame rate:
Video output connector:
Protocols:



Enclosure and mounting
Enclosure type:
Enclosure application:
Mounting:
Box
IP 67 and NEMA‑4X
Surface mount, pendant wall mount, corner mount, pipe mount







Camera movements
Video latency:
Pan range and speed:
Pan speed:
Tilt range:
Tilt speed:
Position presets:
Position preset activation:
Min 120ms, Max 240ms
N/A
N/A
N/A
N/A
N/A
N/A



Intelligence
Video motion detection:
Privacy zone masking:
Anti-tamper:

Alarm-triggered refresh rate:
Yes
Four independent areas, fully programmable
Global change, scene too bright, scene too dark, scene too noisy,
reference check
Via Alarm input/ Motion/Audio alarm / Video loss alarm

Power supply:
Power-over-Ethernet

Ambient conditions:
Minus 20 degrees to + 50 degrees
Mono
H.264 (ISO/IEC 14496-10); M-JPEG, JPEG
4CIF 704 x 576,
Adjustable up to 25 images per second
STP, 10/100 Base-T, auto-sensing, half/full duplex, RJ45.
RTP Telnet, UDP, TCP, IP, HTTP, HTTPS, FTP, DHCP, IGMP
V2/V3, ICMP, ARP, SMTP, SNTP, SNMP, 802.1x, UPnP
Provision and Installation of CCTV at the Port of Dover
10
IMO 13 250/2
Volume 3 – Statement of Requirements, Part C – Appendix 1: List of Camera Specifications.Final.September2013