®
DMX
DRY LOCATION
DMX 4-CHANNEL DECODER
12VDC
24VDC
COMPATIBLE
SPECIFICATION SHEET
OVERVIEW
The DMX 4-Channel Decoder is a key component used for pairing low
voltage LED tape lights and fixtures with a DMX controller. It works by
translating a DMX signal sent from the DMX controller into a PWM signal
used to dim or control LED lights.
This DMX Decoder features a digital display that is much easier to work
with than traditional dip-switches, as well as a screw-down terminal
block for secure wiring connections. When used with our DMX Splitter,
there is virtually no limit to the number of color-changing LED tape lights
or fixtures required for your installation.
FEATURES & BENEFITS
• Compatible with most DMX controls
• Easy to use Digital Display (no dip-switches)
• Connect multiple units in series with standard CAT5 cable
• UL Recognized Component. File # E484300
APPROVED LED LUMINAIRES
Compatible with all Diode LED 12V and 24VDC constant voltage tape
lights and fixtures.
Item #
Project
SPEC SHEET | DMX 4-CHANNEL DECODER | SS040617-3.0 | 1 OF 4
SPECIFICATIONS
MODELS
• Input from Driver¹: 12-24VDC constant voltage
• Output to Load: 12-24VDC Constant Voltage
• Input Signal from DMX Control: DMX512
• Output Signal to Load: PWM
• Output Signal Frequency: 200 - 1,500 Hz; 0.8 milliseconds
• Max Load: 4 CH x 96W/192W (12V/24V)
• DMX Connection Ports: RJ45 (for CAT5 cable)
• Max Daisy-Chain Units (DMX Signal)²: 10 Units. After 10 units a DMX
8-Way Splitter (DI-1804) must be installed to extend DMX signal.
• Compatible Power Supply: 12-24VDC constant voltage driver
• Power Failure Memory: Yes
• Environment: Suitable for indoor / dry location
• Ambient Temp³: -4 ~ 104°F (-20 ~ 40°C)
• Operating Temp⁴: -4 ~ 122°F (-20 ~ 50°C)
• Environment: Indoor / damp location
• Dimensions: 6.50 x 2.40 x 1.24 in. (L x W x H)
• Weight: 0.58 lbs. (9.4 oz.)
DI-1810 (formally DI-1918)
Note: UL Report will indicate model DI-1918. This is the same
model as DI-1810.
ACCESSORIES
For a list of compatible accessories, see the ‘DMX Accessories’
Specification Sheet.
MAXIMUM DAISY-CHAIN DMX DECODERS
A maximum of 10x DMX Decoders may be connected together via
RJ45 DMX Connection Ports. DMX signal may be extended further
by installing a DMX 8-Way Splitter (DI-1804) after the 10th DMX
Decoder.
COMPLIANCE & REGULATORY APPROVALS
Safety
• UL Recognized Component US/CA - Controller. File # E484300.
• CE Compliant
Environmental
• RoHS Compliant
MECHANICAL DIAGRAMS
V+
V−
DC OUTPUT
12 - 24VDC, 4CH x 8A
DMX512
RJ45 Con
Pin 1: Data +
Pin 2: Data −
Pin 7: GND
Pin 8: GND
5/16 in. (8mm)
0-5
0-9
0-9
DMX Start Channel
E484300
tc: 167°F
CH1
DI-1810 (cat: DI-1918)
CH2
DMX DECODER
CH3
V−
V+
®
DC INPUT
12-24VDC
32.5A
87654321
DMX-512
Data Ports
(RJ45 Jack)
V+
87654321
8 7 65 4 3 2 1
Pin 1: Data +
Pin 2: Data Pin 7: Ground
Pin 8: Ground
V+
CH4
From Driver
12-24VDC
R
2.40 in.
R
G
G
To RGB(X) Load
12-24VDC
B
B
W
W
6.50 in.
1.24 in.
1. Ensure to specify a compatible driver and fixture with the same voltage specifications. Multiple decoders may be connected to a compatible LED driver with a single output.
2. A maximum of 10x DMX Decoders may be connected together via RJ45 DMX Connection Ports. DMX signal may be extended further by installing a DMX 8-Way Splitter (DI-1804)
after the 10th DMX Decoder.
3. Do not install product in an environment outside the listed ambient temperature. Exceeding the maximum ambient temperature may damage the controller and/or fixture.
4. Operating temperature is measured according to the minimum and maximum ambient temperature environment.
SPEC SHEET | DMX 4-CHANNEL DECODER | SS040617-3.0 | 2 OF 4
SYSTEM DIAGRAM
The following diagram is provided as an example system design. CAT5 (RJ45 connections) data cables are the most cost-effective solution for transmitting
DMX-512 signals. XLR-3 cables may also be installed but require an additional adapter for connecting to DMX decoders.
DMX Controller
Installed in Wall Box‡
Class 2 Low Voltage Driver**
Installed in Junction Box‡
N
N
G*
AC Power
50/60Hz
Power
Input
DMX Data
Output
Output
L
Input
L
Power input of DMX controllers may vary.
See DMX controller specifications to ensure
appropriate high or low voltage power input.
G
+
-
V+
V-
RJ45 Splice Cable
Wiring Connections
Brown
Ground
White/Orange
Data +
Orange
Data -
Install applicable wire gauge / type
CAT5 / Ethernet Cable (RJ45 Connections)
V-
V+
RJ45 Coupler
RJ45 Splice Cable
V+
V+
V-
CH1 - R
V+
CH1
V+
R
CH2
CH3
G
B
V+
CH1
V+
R
CH2
CH3
CH4
G
B
W
White/Brown wire may be used as
an additional ground.
CH2 - G
Data IN
0-5 0-9 0-9
Data OUT
CH3 - B
CH4 - W
RGB Tape Light / Fixture‡‡
DMX Decoder
V-
V+
V+
V+
V-
CH1 - R
CH2 - G
Data IN
0-5 0-9 0-9
Data OUT
CH3 - B
CH4 - W
RGBW Tape Light / Fixture‡‡
DMX Decoder
CH4 - W connection only utilized for RGBW / RGB(X) installation.
Wall Washer / DMX-512 Fixture‡‡
RJ45 / XLR-3
Adapter Connector
AC Power
50/60Hz
MAXIMUM DAISY-CHAIN DMX DECODERS
A maximum of 10x DMX Decoders may be connected together via
RJ45 DMX Connection Ports. DMX signal may be extended further
by installing a DMX 8-Way Splitter (DI-1804) after the 10th DMX
Decoder.
SPEC SHEET | DMX 4-CHANNEL DECODER | SS040617-3.0 | 3 OF 4
ADDITIONAL RESOURCES
DMX ACCESSORIES Specification Sheet
DMX 4-CHANNEL DECODER Installation Guide
VOLTAGE DROP CHARTS
SAFETY / WARNINGS / DISCLOSURES
1.Install in accordance with national and local electrical code regulations.
2.This product is intended to be installed and serviced by a qualified,
licensed electrician.
3.DO NOT connect directly to high voltage power. Install with a
compatible Class 2 constant voltage LED driver (power supply).
4.Only install compatible 12V and 24VDC constant voltage luminaires.
5.This product is rated for indoor installation and is not protected
against moisture.
6.Do not modify product beyond instructions or warranty will be void.
WARRANTY
Limited Warranty
This product has a one (1) year limited warranty from the date of
shipment. This warranty does not include the additional accessories
referenced in this specification sheet. Complete warranty details for
fixtures and additional accessories are available at www.DiodeLED.com
under the ‘Tools & Resources’ tab. For warranty related questions please
contact product support.
Consumer’s Acknowledgment
Diode LED stands behind its products when they are used properly
and according to our specifications. By purchasing our products, the
purchaser agrees and acknowledges that lighting design, configuration
and installation is a complex process, wherein seemingly minor factors
or changes in layout and infield adjustments can have a significant
impact on an entire system. Choosing the correct components is
essential. Diode LED is able to work with the original purchaser to make
an appropriate product selection to the extent of the limited information
that the customer can provide, but it is virtually impossible for Diode
LED to design a system that foresees every unknown factor. For this
reason, this Warranty does not cover problems caused by improper
design, configuration or installation issues. Any statement from a Diode
LED employee or agent regarding a customer’s bill of goods and/or
purchase order is NOT an acknowledgment that the products purchased
are designed and configured correctly. The purchase agrees and
acknowledges that it is the customer’s responsibility to adhere strictly
to all information contained in the Product Specification Sheets.
There is often more than one way to design, configure and layout an
LED lighting application properly to achieve the same lighting effect.
Diode LED strongly recommends that licensed professionals be used
in the design and installation of lighting systems that include Diode
LED products. The specifications include important information that
a designer and installer should carefully review and strictly follow.
Qualified designers and certified and/or licensed installers, with access
to the final installation environment, customer goals, and Diode LED
product specifications can make the requisite decisions appropriate for
a successful finished lighting application.
®
© 2017 Elemental LED, Inc. All rights reserved.
Specifications are subject to change without notice.
Toll Free: 877.817.6028 |­‌ Fax: 415.592.1596 | www.DiodeLED.com | [email protected]
SPEC SHEET | DMX 4-CHANNEL DECODER | SS040617-3.0 | 4 OF 4