1
2
Ensure all required parts are
present.
surface.
Drill a 9/16” diameter hole at the
desired location on the mounting
3
Remove the hex nut and mounting
washer from the canopy assembly.
Wire Leads
Hex Nut
Mounting Washer
9/16”
dia. hole
Canopy Assembly
P1 canopy shown for example
4
P1 canopy shown for example
Feed the wire leads and threaded
nipple into the mouinting hole.
5
Place the mounting washer and hex
nut over the wire leads and thread
onto the nipple to secure the assembly to the
mounting surface.
6
Connect the secondary wires to
the secondary side of the driver.
Threaded Nipple
120V
Tighten the
hex nut
P1 canopy shown for example
P1 canopy shown for example
Attach the pendant adapter to the
canopy by inserting the threaded
portion into the coupler on the canopy and
thread clock-wise.
7
Basic installation is now complete.
Wire leads may now be connected
to remote low voltage power supply.
6
P3
Canopy
finished installation
P2
Canopy
P4
Canopy
finished installation
P2 canopy shown for example
Attach the pendant adapter to the
8
canopy by inserting the threaded
portion into the coupler on the canopy. Thread
into the canopy by turning the knurled wheels
at the top of the adapter.
Black knob is for
locking purposes
Hold here
when
threading
NOT here
P1 canopy shown for example
13615 Marquardt Ave. Santa Fe Springs, CA 90670
Ph. 562-407-3079 . Fx. 562-407-3069
www.primalighting.com
Follow all local and national electrical codes.
For assistance please call Prima Customer Service at 562-407-3079
P1
Canopy
P1 canopy shown for example
P1 / P2 / P3 / P4 Monopoint
Instruction Sheet
IMPORTANT Please read these instructions prior to installation. Refer to the Prima catalog for pr
res.
Prima is not r
re or system failure caused by unsupported lamps. Contact Prima customer service for the latest updates on
which lamps we support and proper usage. Prima low voltage transformers must be used with all Prima Lighting product installations. All warranties
are void if Prima transformers are not used. Prima’s catalogs provide general information and suggestions for proper dimmer usage. Please consult
our customer service department with any questions regar
responsible for any damage caused by improper
re to all local and national electrical codes prior to installation.
Rev. 121714
Continue to thread the adapter into
9
the coupling until it stops. To lock
the adapter in place, rotate the knurled
locking ring clockwise until its tight. There
should now be a gap between the two knobs.
Rotate black
knob to lock
Notes:
Always disconnect power
prior to installation or
maintenance.
*Always use dedicated breaker/branch
circuit line for Prima low voltage system.
Do not mix with fluorescent lighting
system on the same circuit.
P1 canopy shown for example
P1 / P2 / P3 / P4 Monopoint
Instruction Sheet
IMPORTANT Please read these instructions prior to installation. Refer to the Prima catalog for pr
res.
Prima is not r
re or system failure caused by unsupported lamps. Contact Prima customer service for the latest updates on
which lamps we support and proper usage. Prima low voltage transformers must be used with all Prima Lighting product installations. All warranties
are void if Prima transformers are not used. Prima’s catalogs provide general information and suggestions for proper dimmer usage. Please consult
our customer service department with any questions regar
responsible for any damage caused by improper
re to all local and national electrical codes prior to installation.
Follow all local and national electrical codes.
For assistance please call Prima Customer Service at 562-407-3079
13615 Marquardt Ave. Santa Fe Springs, CA 90670
Ph. 562-407-3079 . Fx. 562-407-3069
www.primalighting.com
Rev. 121714