BABA FARID COLLEGE OF ENGINEERING & TECHNOLOGY BATHINDA
GUIDELINES FOR B. TECH. INDUSTRIAL TRAINING REPORT
Project Report Submission Guidelines
Text:
The text should be typed in 12 font size Times New Roman style in 1.5 spacing on one
side of A4 size page. The heading should be of Times New Roman font size 14 and
Bold. The Captions for figures should be typed at its bottom; for example 6th figure in
Chapter 5 should be captioned as Fig. 5.6 Title of Figure. The captions for tables should
be typed at its top; for example 8th table in Chapter 2 should be captioned as Table 2.8
Title of Table.
Arrangement of Contents of Project Report:
The sequence in which the project report may be arranged as follows:
1. Cover Page or Title Page
2. Certificate
3. Abstract
4. Acknowledgement
5. Table of Contents
6. List of tables
7. List of Figures
8. List of Symbols, Abbreviations
9. Chapters I, II…
10. Appendices
11. References
1
Sample of table of contents:
CONTENTS
_____________________________________________________________________
S.No.
Title
Page
No.
Candidate’s Declaration
iii
Abstract
iv
Acknowledgement
v
List of Figures
viii
List of Tables
xi
Introduction
1
1.1
asaskdjasjdg
1
1.2
jaskjasxj
1
1.3
sahdasjd
3
1.4
kasjcbasj
5
1.5
bkasjsal
7
dbskjdhqwodhqwoijqw
8
2.1
jhassdjlaskjdk
8
2.2
mncxlaskdjod
8
2.3
ckasjkasjas
9
2.4
mncskacskdjaskdjsdklas
Chapter 1
Chapter 2
13
2
 Numbering of Chapters, Sections and Sub-sections:
The numbering of Chapters, division and sub-divisions should be done using
Arabic numerals only and further decimal notation should be used for numbering
the divisions and subdivisions within a chapter. For examples sub-division 5
under division 2 belonging to chapter 3 should be numbered as 3.2.5
 Page, Dimensions and Margin:
The dimensions of the final bound 3 copies report should be Standard A4 size
(297mm x210mm) paper may be used for preparing the copies. The report (at the
time of submission) should have the following page margins:
o Top and Bottom edge: 25 mm (1 inch)
o Left and right side: 32 mm (1.25 inches)
 Page Numbering:
All pages numbers should be typed at the center of page bottom. The preliminary
pages of the report (such as Title page, Acknowledgement, Table of Contents,
List of tables and figures, Notations, Abbreviations etc.) should be numbered in
lower case Roman numerals.
 Binding Specifications
Project Report submitted (3 copies) should be hard bound in Black color (Matt
finish) hard rexin binding with golden screen printing of the cover page.
 Number of Copies to be submitted
Three copies (one student copy, one for college record and one for departmental
library) are to be submitted.
At the time of Internal/External Viva, the students must possess
1. Training certificates in original (Software as well as Industrial training).
2. Attendance Report counter signed by Training In charge.
3. Project Assessment of 250 marks (Evaluation sheet) by Faculty
advisor/ Inspection in charge/Training Officer duly stamped & sealed (in
envelop) by the organization. (Pl ignore if already submitted).
4. CD containing Presentation of Project, Source Code of project, Soft
copy of report for both trainings (Software as well as Industrial training).
5. Daily Dairy
6. Three copies of Project Reports (one student copy, one for
college/Univ. record and one for library) , which should be hard bound
in Black color (Matt finish) hard rexin binding with golden screen
printing of the cover page. Report should be strictly as per the
prescribed format (refer to College Website).
3
FORMAT OF COVER PAGE (Hard Bound)
TITLE OF REPORT
(Times New Roman, Font size=24)
Submitted by:
Student’s name
Univ roll no.
DEPARTMENT OF …………………………………………….
BABA FARID COLLEGE OF ENGINEERING &TECH.
Muktsar Road, Bathinda-151001, Punjab (INDIA)
(Approved by AICTE, New Delhi and Affiliated to IKGPTU, Jalandhar)
Month, Year
4
FORMAT FOR INSIDE COVER PAGE
A REPORT ON
TITLE OF PROJECT (24pt)
SUBMITTED IN PARTIAL FULFILLMENT FOR AWARD DEGREE OF (12pt)
BACHELOR OF TECHNOLOGY (14pt)
IN
................................................... (14pt)
BY
NAME OF STUDENT (14pt)
(UNIV ROLL NO.)
UNDER THE GUIDANCE OF
NAME OF HOD
DEPARTMENT OF …………………………………
BABA FARID COLLEGE OF ENGINEERING &TECH.
Muktsar Road, Bathinda-151001, Punjab (INDIA)
(Approved by AICTE, New Delhi and Affiliated to IKGPTU, Jalandhar)
5
Certificate
Certified that this project/training report entitled “Title of the Project”
submitted by Name of the Student (University Roll Number), student of
______________(Branch),
Baba
Farid
College
of
Engineering
&
Technology, Bathinda in the partial fulfillment of the requirement for the
award of Bachelors of Technology (Name of Branch) Degree of IKGPTU,
Jalandhar, is a record of students own study carried under my supervision &
guidance.
This report has not been submitted to any other university or institution for
the award of any degree.
Name & Sign of Project Guide
Designation
6
Acknowledgement
7