In-Die Transfer Systems
DISTRICT BOARD
DISTRICT DIRECTOR
Tony Pascariello
Hobson & Motzer, Inc.
DISTRICT CHAIR
Steve Izzo
Bridgeport Fittings, Inc.
MEMBERSHIP CHAIR
Bob Maley
Ulbrich Specialty Steel, Inc.
MEMBERS AT LARGE
Jason Howey
Okay Industries, Inc.
Lucas Karabin
Acme Monaco Corporation
TREASURER
Ed Tremblay
Okay Industries, Inc.
DISTRICT ADMINISTRATOR
Genene Patrissi
Fairfield University
Directions:
From North Haven (south):
I-91 North, to Rt. 691 West
to I-84 West, to Rt. 8
North. (Follow Rt. 8 North
Directions Below).
From Hartford (east):
I-91 North or South to I-84
West towards Waterbury to
Rt. 8N (Follow Rt. 8 North
Directions Below).
From Danbury (west):
I-84 East to Rt. 8 North
(Follow Rt. 8 North
Directions Below)
From Rt. 8 North:
Take Exit 36 – Huntington
Avenue. Turn right at the
end of the exit. Follow for
approximately 2 miles then
turn left onto Farmwood
Road. (Farmwood Road is
at the intersection of
Lakewood Road and North
Main St.) Ponte’ Club & La
Bella Vista is
approximately ¾ miles
down the road on the righthand side.
Presented by Mr. Gary Ruby, M.S. Willett, Inc.
Date: Wednesday, May 17, 2017
Location: La Bella Vista at the Pontelandolfo Club
380 Farmwood Road
Waterbury, CT 06704
Phone:
203-574-3036
Registration: 5:00 - 5:45 p.m.
Social Hour: 5:45 - 6:45 p.m.
Dinner:
6:45 - 7:45 p.m.
Presentation: 7:45 - 8:45 p.m.
.
We welcome you to join us for this new presentation on the topic of in-die
transfer systems presented by Mr. Gary Ruby, Director of Engineering
Development & Sales at M.S. Willett, Incorporated.
Gary began his career at M.S. Willett in 1980 where he completed his
Machinist/Toolmaker Apprenticeship program. Over the past 37 years at
Willett, he’s been promoted several times in positions of increasing
responsibility working with the assembly and development of complex transfer
systems and field installations. Other positions included tool & system design,
and project engineering. Throughout his career Gary has always taken a
hands-on approach.
Willett is headquartered in Cockeysville, MD, which is located between
Baltimore, MD and York, PA. Willett operates two business units: Production
Division and the Tool & Die Division, which while separate and independently
run entities, frequently collaborate to achieve customer expectations. Willett,
an ISO 9001: 2008 registered company, operates in two buildings over
60,000 square feet.
The Production Division is a full-service manufacturer of stamped
components in presses with capabilities from 30 to 400 tons and with material
up to 0.150" at 40" and 0.250" at 10" mild steel (coil) and .375 thick in strip.
They are off-load specialists experienced in single items or entire product
lines from simple to complex shapes. They also offer sheet metal fabrication
services. A diverse range of processes are used to fashion sheet metal into
finished products. These processes include precision cutting, forming, welding
and finished services.
The Tool & Die Division is a full-service tooling and machine shop with
experience in machining all materials from space age to tool steels. Willett's
engineering and design team's expertise and computer aided design
capabilities supports its customers from part design and prototype to
completed manufactured part for a variety of industries. They design and
engineer close tolerances in blanking, compound, deep draw, progressive
and gag dies, part transfer systems, replacement and spare tooling and
complete turn-key systems.
The Presentation will cover:




Single and Multiple Lane Transfers
Transfers with Progressive Dies in Same Press
Multiple Transfer Devices Being Used in One Die
Dial Transfer Systems; One & Two Dial Systems
REGISTRATION FORM LOCATED ON PAGE 2 OF NOTICE
Fax, E-mail or Mail
Registrations to:
Genene Patrissi
(No voice mail registrations)
32 Limewood Avenue
Branford, CT 06405
Phone: 203-824-0392
Fax: 203-208-5780
E-mail:
[email protected]
For more information on this
and other district programs
and benefits, please visit us
online at
pma.org/districts/CT/south
ern_new_england/
Fax, E-mail or Mail Registrations to:
Genene Patrissi
32 Limewood Avenue
Branford, CT 06405
Phone: 203-824-0392
Fax: 203-208-5780.
E-mail: [email protected]
(No voice mail registrations please)
Cost of attendance: $60 per member, $75 per nonmember.
(Includes multi-course buffet dinner)
Deadline for registration is no later than Thursday, May 11, 2017
(Note: A 72-hour cancellation notice must be received for credit consideration towards a future meeting)
Who should attend: Tool Designers, Toolmakers, Tooling Engineers, Automation Engineers, Production Managers,
Purchasing Agents, Manufacturing Engineers, Process Engineers and Engineering Managers.
Dear Genene:
Here is our reservation(s) for the “In-Die Transfer Systems” presentation on Wednesday, May 17,
2017 at La Bella Vista at the Ponte’ Club in Waterbury.
Member
Nonmember
Company: __________________________________________________
Address: ___________________________________________________________
City: ____________________________ State: _____________ Zip: ____________
Signature ___________________________________________________________
Phone: ____________________________ Fax: ___________________________
E-mail Address: ______________________________________________________
Please make checks payable to the “PMA Southern New England District” and mail or fax
registrations to the above address/fax number.
THIS RESERVATION COVERS THE FOLLOWING INDIVIDUALS:
Names:
Title/Position (required):
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
Join the growing number of companies benefiting from PMA membership. A variety of tangible savings and benefits are available
to your company:
Legislative Advocacy
Informative Statistical Reports
Networking Opportunities
Training Programs
Safety Consultation
Shipping Discounts
To join PMA, contact Bob Maley, SNE District Membership Chair, at 203-623-6398
Or contact Janet Krall at PMA, 216-901-8800
Fax: 216-901-9190