Location:
®
LARGE CAPACITY PLASTIC
GREASE INTERCEPTOR
XL-MI-G-PL-750
Specification: MIFAB® XL-MI-G-PL-750, 75 GPM sand and grease interceptor with 750 lb. grease design capacity. Interceptor has a limited
lifetime warranty and is made in the USA out of seamless, rotationally molded High Density Polyethylene with 3/8” uniform wall thickness.
Interceptor designed for above or below ground installation. Interceptor includes an adjustable lid system, external, vented flow control fitting,
sample port access, and multiple outlet options. The steel encased composite lid provides a water / gas tight seal and has a minimum of 20,000
lbs. load capacity. The lid is designed in accordance with the loading requirements of AASHTO H20.
Function: The interceptor retains sand and sediment. Used in restaurants, kitchens, institutions, industrial facilities such as food processing
and packaging plants and other types of food processing areas where fat, oil and grease (FOG) drains with the wastewater. Narrow width
permits access through doorways and down stairwells. High Density Polyethylene construction ensures a lightweight installation process (two
people can move and install it).
20,000 LB. LOAD RATED
STEEL ENCASED
COMPOSITE, GASKETED
COVER AND COLLAR
50" (1267)
22" (558)
24.5" (625)
thru
15.5" (394)
STANDARD 18"
DIAMETER
CORRUGATED
DRAINAGE PIPE
4" NO
HUB INLET
37"
(940)
IN
DE A
MA E US
TH
(18" LONG PIECES
PROVIDED AS
STANDARD
CAN BE CUT
DOWN TO
8 1/2" FOR
"C" OF 16")
33.5"
(851)
(WIDTH)
49 3/4"
(1263)
U.S. Patent
# 9,551,142
OPTIONAL SIDE OUTLETS
25.5"
(651)
The XL-MI-G-PL-750 is tested and
certified to the following standards:
PDI-G-101, ASME A112.14.3,
CSA B481.1 and is listed with IAPMO.
3/8" THICK,
ROTATIONALLY
MOLDED H.D.P.E.
BODY
4" NO HUB INLET WITH INTERNAL VENT AND DEEP
FLOW GUIDE
FORKLIFT
ACCESS POINT RIBBED DESIGN PROVIDES
EXTRA STRUCTURAL
GRIP POINTS FOR
INTEGRITY FOR IN
ANCHOR KIT
GROUND INSTALLATION
4" NO HUB OUTLET WITH
INTERNAL AIR RELIEF
BYPASS AND DEEP SEAL TAP
MODEL NO.
FLOW
RATE (GPM)
GREASE DESIGN
CAPACITY
LIQUID
CAPACITY (GAL)
SHIPPING
WEIGHT(Lbs.)
75
750Lbs (105GAL)
140
150
XL-MI-G-PL-750
24"
(612)
thru
15.5"
(394)
18" (457)
SAMPLE PORT ACCESS
49 3/4"
(1263)
37"
(940)
25.5"
(651)
50" (1267)
SUFFIX
-AK
-C
-CL
-DCL
-DI
-DP
-EP
-FL-C
-F6 -HLA
-LHSI
-LHSO
-OP
-RHSI
-RHSO
-SB
-SP
-SP-OF
-T
Note: for the -DCL option, the floor
to top of lid dimension is 39 7/8”
OPTIONAL VARIATIONS
High water anchor kit (set of two)
Lid extension (specify “C” dimension required) (Max. of 72”)
Holdown brackets for lid (when installed above ground)
Direct Connect Lid (lid bolted to top of body)
Ductile iron lid & collar
Dosing pump
Enzyme port
Membrane clamp kit
6” No Hub Inlet / Outlet connection
High level alarm
4” no hub inlet on left hand side
4” no hub outlet on left hand side
Internal flow control*
4” no hub inlet on right hand side
4” no hub outlet on right hand side
Sediment bucket
External Sample Port (for existing construction. Inlet and Outlet on the same level)
External Sample Port (for new construction. Inlet higher than the outlet).
Female threaded connections
CALIFORNIA PROPOSITION 65 WARNING. This product contains chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.
Job Name:
Page No:
Section No:
Contractor:
Schedule No:
Purchase Order No:
MIFAB reserves the right to make changes in material and design without formal notice and obligation.
USA: 1-800-465-2736 www.mifab.com CAN: 1-800-387-3880
2017-04-05