RX7620 not booting in Linux Advanced ver3
HI Mr Ken
From the message
::
mptscsih: ioc1: id=1 OldAbort: unknown target (sc=e0000000007fd980) SCSI
host 5 abort (pid 135) timed out - resetting SCSI bus is being reset for
host 5 channel 0.
mptscsih: ioc1: id=1 OldReset: scheduling BUS_RESET SCSI IO
(sc=e0000000007fd980)
SCSI host 5 channel 0 reset (pid 135) timed out - trying harder SCSI bus
is being reset for host 5 channel 0.
mptscsih: ioc1: id=1 OldReset: scheduling BUS_RESET SCSI IO
(sc=e0000000007fd980)
mptbase: ioc1: WARNING - IOCStatus(0x0048): SCSI Task Terminated
======>>> SCSI reset & terminating x 02 counts
::
::
::
[/sbin/fsck.ext3 (1) -- /var] fsck.ext3 -a /dev/cciss/c0d0p7 [ OK ]
Mounting local filesystems: [ OK ] Enabling local filesystem quotas:
[ OK ] Enabling swap space: [ OK ]
INIT: Entering runlevel: 3
Entering non-interactive startup
Checking for new hardware
=============>> should have an [ OK } but
missing...
Please verify the following due to the reason,
1. After the CE install the system, did you add any new devices like HDD
etc...
2. This seems like doing a IO checking and seems at certain bus it hang.
At this point of time, i suspect certain HW might be causing the system
to hang when checking for device.
As for the notebook keyboard, I was not able to find out any issue on
why the direction keys cannot be use. If possible, you may connect
another set of notebook to the MP Console and confirm whether the other
notebook direction is able to function.
action plan:
what: Check on Physical Connection on HW and I/O cards on the I/O Board
- Check on the HDD as well
- Check if notebook connection through MP card, direction key
able to function
If needed boot to Single User Mode and boot up level by level
why: Not able to boot up and hang at checking for new devices messgae
Cheers
chong
Dear Chong
Below is the message
IOC: sx1000 0.1 HPA 0xf8120003000 IOVA space 1024Mb at 0x80000000 Linux
NET4.0 for Linux 2.4 Based upon Swansea University Computer Society
NET3.039 Initializing RT netlink socket
perfmon: version 1.6 IRQ 238
perfmon: Itanium 2 PMU detected, 16 PMCs, 18 PMDs, 4 counters (47 bits)
PAL Information Facility v0.5 EFI Variables Facility v0.05 2002-Mar-26
Total HugeTLB memory allocated, 0 Call gate_vma_init Starting kswapd
VFS: Disk quotas vdquot_6.5.1
aio_setup: num_physpages = 523775
aio_setup: sizeof(struct page) = 112
Hugetlbfs mounted.
pty: 2048 Unix98 ptys configured
Serial driver version 5.05c (2001-07-08) with MANY_PORTS MULTIPORT
SHARE_IRQ DETECT_IRQ SERIAL_PCI SERIAL_ACPI enabled tyS0 at
0xc0000f0100004000 (irq = 49) is a 16550A
PCI: Found IRQ 49 for device 00:00.0
ttyS1 at iomem 0xc0000f0100007000 (irq = 49) is a 16550A
PCI: Found IRQ 49 for device 00:00.1
ttyS0 at iomem 0xc0000f0100004000 (irq = 49) is a 16550A
ttyS2 at iomem 0xc0000f0100004010 (irq = 49) is a 16550A
ttyS3 at iomem 0xc0000f0100004038 (irq = 49) is a 16550A EFI Time
Services Driver v0.4
NET4: Frame Diverter 0.46
RAMDISK driver initialized: 256 RAM disks of 8192K size 1024 blocksize
Uniform Multi-Platform E-IDE driver Revision: 7.00beta4-2.4
ide: Assuming 33MHz system bus speed for PIO modes; override with
idebus=xx ide-floppy driver 0.99.newide ide-floppy driver 0.99.newide
md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
Initializing Cryptographic API
NET4: Linux TCP/IP 1.0 for NET4.0
IP: routing cache hash table of 524288 buckets, 8192Kbytes
TCP: Hash tables configured (established 16777216 bind 65536) Linux IP
multicast router 0.06 plus PIM-SM Initializing IPsec netlink socket
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
RAMDISK: Compressed image found at block 0 Freeing initrd memory: 1872kB
freed
VFS: Mounted root (ext2 filesystem).
SCSI subsystem driver Revision: 1.00
Red Hat nash version 3.5.13.6 starting
Mounted
Loading
Loading
Loading
/proc filesystem
scsi_mod.o module
sd_mod.o module
diskdumplib.o modulePCI: Found IRQ 50 for device 00:03.0
Loading sym53c8xx.o module
sym53c8xx: at PCI bus 0, device 3, function 0
sym53c8xx: 53c1010-66 detected with Symbios NVRAM
PCI: Found IRQ 51 for device 00:03.1
sym53c8xx: at PCI bus 0, device 3, function 1
sym53c8xx: 53c1010-66 detected with Symbios NVRAM
PCI: Found IRQ 52 for device 1d:01.0
sym53c8xx: at PCI bus 29, device 1, function 0
sym53c8xx: 53c1010-66 detected with Symbios NVRAM
PCI: Found IRQ 53 for device 1d:01.1
sym53c8xx: at PCI bus 29, device 1, function 1
sym53c8xx: 53c1010-66 detected with Symbios NVRAM
sym53c1010-66-0: rev 0x1 on pci bus 0 device 3 function 0 irq 50
sym53c1010-66-0: Symbios format NVRAM, ID 7, Fast-80, Parity Checking
sym53c1010-66-0: on-chip RAM at 0xc0000000
sym53c1010-66-0: restart (scsi reset).
sym53c1010-66-0: handling phase mismatch from SCRIPTS.
sym53c1010-66-0: Downloading SCSI SCRIPTS.
sym53c1010-66-1: rev 0x1 on pci bus 0 device 3 function 1 irq 51
sym53c1010-66-1: Symbios format NVRAM, ID 7, Fast-80, Parity Checking
sym53c1010-66-1: on-chip RAM at 0xc0002000
sym53c1010-66-1: restart (scsi reset).
sym53c1010-66-1: handling phase mismatch from SCRIPTS.
sym53c1010-66-1: Downloading SCSI SCRIPTS.
sym53c1010-66-2: rev 0x1 on pci bus 29 device 1 function 0 irq 52
sym53c1010-66-2: Symbios format NVRAM, ID 7, Fast-80, Parity Checking
sym53c1010-66-2: on-chip RAM at 0xc8010000
sym53c1010-66-2: restart (scsi reset).
sym53c1010-66-2: handling phase mismatch from SCRIPTS.
sym53c1010-66-2: Downloading SCSI SCRIPTS.
sym53c1010-66-3: rev 0x1 on pci bus 29 device 1 function 1 irq 53
sym53c1010-66-3: Symbios format NVRAM, ID 7, Fast-80, Parity Checking
sym53c1010-66-3: on-chip RAM at 0xc8012000
sym53c1010-66-3: restart (scsi reset).
sym53c1010-66-3: handling phase mismatch from SCRIPTS.
sym53c1010-66-3: Downloading SCSI SCRIPTS.
scsi0 : sym53c8xx-1.7.3c-20010512
scsi1 : sym53c8xx-1.7.3c-20010512
scsi2 : sym53c8xx-1.7.3c-20010512
scsi3 : sym53c8xx-1.7.3c-20010512
blk: queue e0000000007ff9b0, I/O limit 1048575Mb (mask 0xffffffffff)
Vendor: _NEC
Model: DVD+RW ND-2100AD Rev: 1.28
Type:
CD-ROM
ANSI SCSI revision: 02
blk: queue e0000000007ff5b0, I/O limit 1048575Mb (mask 0xffffffffff)
Loading mptbase.o moduleFusion MPT base driver 2.06.16.01 Co pyright (c)
1999-2005 LSI Logic
PCI: Found IRQ 56 for device 54:01.0
mptbase: Initiating ioc0 bringup
ioc0: 53C1030: Capabilities={Initiator,Target}
PCI: Found IRQ 57 for device 54:01.1
mptbase: Initiating ioc1 bringup
ioc1: 53C1030: Capabilities={Initiator,Target}
mptbase: 2 MPT adapters found, 2 installed.
Loading mptscsih.o moduleFusion MPT SCSI Host driver 2.06.16.01
scsi4 : ioc0: LSI53C1030, FwRev=01032341h, Ports=1, MaxQ=203, IRQ=56
scsi5 : ioc1: LSI53C1030, FwRev=01032341h, Ports=1, MaxQ=203, IRQ=57
scsi : aborting command due to timeout : pid 135, scsi5, channel 0, id
1, lun 0 Inquiry 00 00 00 ff 00
mptscsih: ioc1: id=1 OldAbort: unknown target (sc=e0000000007fd980) SCSI
host 5 abort (pid 135) timed out - resetting SCSI bus is being reset for
host 5 channel 0.
mptscsih: ioc1: id=1 OldReset: scheduling BUS_RESET SCSI IO
(sc=e0000000007fd980)
SCSI host 5 channel 0 reset (pid 135) timed out - trying harder SCSI bus
is being reset for host 5 channel 0.
mptscsih: ioc1: id=1 OldReset: scheduling BUS_RESET SCSI IO
(sc=e0000000007fd980)
mptbase: ioc1: WARNING - IOCStatus(0x0048): SCSI Task Terminated
Vendor: HP
Model: C5683A
Rev: C305
Type:
Sequential-Access
ANSI SCSI revision: 03
blk: queue e0000000007ff1b0, I/O limit 17592186044415Mb (mask
0xffffffffffffffff)
Loading qla2300.o module
qla2x00_set_info starts at address = a0000000001b4b50
PCI: Found IRQ 59 for device a9:01.0
qla2x00: Found VID=1077 DID=2312 SSVID=1077 SSDID=131
scsi(6): Found a QLA2312 @ bus 169, device 0x1, irq 59, iobase
0xc0000f4110020000
scsi(6): 64 Bit PCI Addressing Enabled.
scsi(6): Configure NVRAM parameters...
scsi(6): Verifying loaded RISC code...
scsi(6): Verifying chip...
scsi(6): Waiting for LIP to complete...
scsi(6): Cable is unplugged...
scsi-qla0-adapter-node=50060b00002fa9d7\;
scsi-qla0-adapter-port=50060b00002fa9d6\;
qla2x00_detect num_hosts=0
PCI: Found IRQ 60 for device c6:01.0
qla2x00: Found VID=1077 DID=2312 SSVID=1077 SSDID=131
scsi(7): Found a QLA2312 @ bus 198, device 0x1, irq 60, iobase
0xc0000f4120020000
scsi(7): 64 Bit PCI Addressing Enabled.
scsi(7): Configure NVRAM parameters...
scsi(7): Verifying loaded RISC code...
scsi(7): Verifying chip...
scsi(7): Waiting for LIP to complete...
scsi(6): LOOP DEAD detected.
scsi(7): Cable is unplugged...
scsi-qla1-adapter-node=50060b00002fa90b\;
scsi-qla1-adapter-port=50060b00002fa90a\;
qla2x00_detect num_hosts=1
scsi6 : QLogic QLA2312 PCI to Fibre Channel Host Adapter: bus 169 device
1 irq 59
Firmware version: 3.03.11, Driver version 7.05.00-RH1
scsi7 : QLogic QLA2312 PCI to Fibre Channel Host Adapter: bus 198 device
1 irq 60
Firmware version: 3.03.11, Driver version 7.05.00-RH1
blk: queue e0000000007ce330, I/O limit 17592186044415Mb (mask
0xffffffffffffffff)
Loading cciss.o module
HP CISS Driver (v 2.4.58.RH1)
PCI: Found IRQ 55 for device 39:04.0
blocks= 286734240 block_size= 512
heads= 255, sectors= 32, cylinders= 35139 RAID 1(0+1)
blk: queue e000000004d8c5b0, I/O limit 17592186044415Mb (mask
0xffffffffffffffff)
Partition check:
cciss/c0d0: p1 p2 p3 p4 p5 p6 p7 p8 p9
Loading jbd.o module
Journalled Block Device driver loaded
Loading ext3.o moduleEXT3-fs: INFO: recovery required on readonly
filesystem.
Creating block devices
Creating root device
Mounting root filesystem
EXT3-fs: write access will be enabled during recovery.
kjournald starting. Commit interval 5 seconds
EXT3-fs: recovery complete.
EXT3-fs: mounted filesystem with ordered data mode.
Freeing unused kernel memory: 368kB freed
INIT: version 2.85 booting
Welcome to Red Hat Enterprise Linux AS
Press 'I' to enter interactive startup.
Configuring kernel parameters: [ OK ] Setting clock (localtime): Thu
Nov 3 11:58:02 MYT 2005 [ OK ] Setting hostname myitopc04: [ OK ]
Your system appears to have shut down uncleanly Press Y within 1 seconds
to force file system integrity check...
Checking root filesystem
/: clean, 116950/786432 files, 784585/1572864 blocks
[/sbin/fsck.ext3 (1) -- /] fsck.ext3 -a /dev/cciss/c0d0p6 [ OK ]
Remounting root filesystem in read-write mode: [ OK ] Activating swap
partitions: [ OK ] Finding module dependencies: [ OK ] Checking
filesystems
/opt: recovering journal
/opt: clean, 11/1310720 files, 49345/2621440 blocks
/script: recovering journal
/script: clean, 11/131072 files, 12329/262144 blocks
/tech_file: recovering journal
/tech_file: clean, 11/131072 files, 12329/262144 blocks
/var: recovering journal
/var: clean, 1127/393216 files, 33264/786432 blocks Checking all file
systems.
[/sbin/fsck.ext3 (1) -- /opt] fsck.ext3 -a /dev/cciss/c0d0p5
[/sbin/fsck.ext3 (1) -- /script] fsck.ext3 -a /dev/cciss/c0d0p9
[/sbin/fsck.ext3 (1) -- /tech_file] fsck.ext3 -a /dev/cciss/c0d0p8
[/sbin/fsck.ext3 (1) -- /var] fsck.ext3 -a /dev/cciss/c0d0p7 [ OK ]
Mounting local filesystems: [ OK ] Enabling local filesystem quotas:
[ OK ] Enabling swap space: [ OK ]
INIT: Entering runlevel: 3
Entering non-interactive startup
Checking for new hardware
HI Mr Ken
Please try to simulate the reboot and provide the exact message shown as
mentioned about "checking device" or where the boot hang.
There is no issue about the notebook connection to the MP card, I'll try
to search for more.
Current findings:
**************
As for the SEL, everything seems fine except for 02 Nov
1597 SFW 0,1,0 *7 e38016dd10e001ae 0000000000005400
FATAL_INTERRUPT_VECTOR
====>>
1597
11/02/2005
04:29:36
Description:
An unrecoverable processor interrupt occured. IPF firmware owned the
processor interrupt vector table (IVT) at the time of the interrupt.
Cause / Action:
Probable bug in System Firmware, EFI driver, EFI app or OS loader (prior
to OS launch). The event data field contains the IVT offset applicable
to the interrupt. See table 5-7 (Interruption Vector Table) in the Intel
ASDM Volume 2.
*****************
Dear Chong
I am selecting D option as below
[uninitialized] MP:VW> sel
Welcome to the SEL (System Event Log) Viewer
The following SEL navigation commands are available:
D: Dump log starting at current block for capture and analysis
F: Display first (oldest) block
L: Display last (newest) block
J: Jump to specified entry and display previous block
+: Display next (forward in time) block
-: Display previous (backward in time) block
<cr>: Repeat previous +/- command
<sp>: Repeat previous +/- command
?: Display help
^B: Exit viewer
The following event format options are available:
K: Keyword
R: Raw hex
T: Text
The following event filter options are available:
A: Alert level
C: Cell
U: Unfiltered
[uninitialized] MP:VWR (<cr>,<sp>,+,-,?,F,L,J,D,K,R,T,A,C,U,^B) >
Attached are the messages
1520 PDHC 0,1
1520
09:04:34
1521 PDHC 0,1
1521
09:04:35
2 4b000b5a01e00150 0100000043672fa2 RESET_CELL
11/01/2005
2 4b000c3901e00151 0100000043672fa3 CELL_POWER_OFF
11/01/2005
1522 MP
1522
09:04:35
1523 MP
1523
09:04:35
1524 MP
1524
09:04:36
1525 PM
1525
09:04:41
1526 MP
1526
09:05:03
1527 MP
1527
09:05:03
1528 MP
1528
09:05:04
1529 PDHC
1529
09:05:04
1530 PDHC
1530
09:11:40
1531 PDHC
1531
09:11:41
1532 MP
1532
09:11:41
1533 MP
1533
09:11:41
1534 MP
1534
09:11:41
1535 PM
1535
09:11:47
1536 MP
1536
09:12:00
1537 MP
1537
09:12:01
1538 MP
1538
09:12:02
1539 PDHC
1539
09:12:02
1540 PDHC
1540
09:18:28
1541 MP
1541
09:18:28
1542 PDHC
1542
0
2 44800ee800e00152 00ffffffff01ff68 CELL_OFF
11/01/2005
0
2 4b000eca00e00154 0100000043672fa3 IO_BP_LPM_OFF
11/01/2005
0
2 4b000ec700e00155 0100000043672fa4 MAIN_BP_LPM_OFF
11/01/2005
0
2 4b000af800e00156 0100000043672fa9 CABPWR_OFF
11/01/2005
0
2 4b000ec600e00157 0100000043672fbf MAIN_BP_LPM_GOOD
11/01/2005
0
2 4b000ec900e00158 0100000043672fbf IO_BP_LPM_GOOD
11/01/2005
0
2 44800ee700e00159 00ffffffff01ff68 CELL_ON
11/01/2005
0,1
2 4b000b5801e0015b 0100000043672fc0 CELL_POWER_GOOD
11/01/2005
0,1
2 4b000b5a01e0015c 010000004367314c RESET_CELL
11/01/2005
0,1
2 4b000c3901e0015d 010000004367314d CELL_POWER_OFF
11/01/2005
0
2 44800ee800e0015e 00ffffffff01ff68 CELL_OFF
11/01/2005
0
2 4b000eca00e00160 010000004367314d IO_BP_LPM_OFF
11/01/2005
0
2 4b000ec700e00161 010000004367314d MAIN_BP_LPM_OFF
11/01/2005
0
2 4b000af800e00162 0100000043673153 CABPWR_OFF
11/01/2005
0
2 4b000ec600e00163 0100000043673160 MAIN_BP_LPM_GOOD
11/01/2005
0
2 4b000ec900e00164 0100000043673161 IO_BP_LPM_GOOD
11/01/2005
0
2 44800ee700e00165 00ffffffff01ff68 CELL_ON
11/01/2005
0,1
2 4b000b5801e00167 0100000043673162 CELL_POWER_GOOD
11/01/2005
0,1
2 4b000b5a01e00168 01000000436732e4 RESET_CELL
11/01/2005
0
2 44800ee800e00169 00ffffffff01ff68 CELL_OFF
11/01/2005
0,1
2 4b000c3901e0016b 01000000436732e4 CELL_POWER_OFF
11/01/2005
09:18:28
1543 MP
1543
09:18:29
1544 MP
1544
09:18:29
1545 PM
1545
09:18:35
1546 MP
1546
09:19:13
1547 MP
1547
09:19:14
1548 MP
1548
09:19:15
1549 PDHC
1549
09:19:15
1550 PDHC
1550
09:34:30
1551 PDHC
1551
09:34:30
1552 MP
1552
09:34:30
1553 MP
1553
09:34:30
1554 MP
1554
09:34:31
1555 PM
1555
09:34:37
1556 MP
1556
09:34:50
1557 MP
1557
09:34:50
1558 MP
1558
09:34:51
1559 PDHC
1559
09:34:51
1560 PDHC
1560
09:42:42
1561 MP
1561
09:42:42
1562 PDHC
1562
09:42:42
1563 MP
0
2 4b000eca00e0016c 01000000436732e5 IO_BP_LPM_OFF
11/01/2005
0
2 4b000ec700e0016d 01000000436732e5 MAIN_BP_LPM_OFF
11/01/2005
0
2 4b000af800e0016e 01000000436732eb CABPWR_OFF
11/01/2005
0
2 4b000ec600e0016f 0100000043673311 MAIN_BP_LPM_GOOD
11/01/2005
0
2 4b000ec900e00170 0100000043673312 IO_BP_LPM_GOOD
11/01/2005
0
2 44800ee700e00171 00ffffffff01ff68 CELL_ON
11/01/2005
0,1
2 4b000b5801e00173 0100000043673313 CELL_POWER_GOOD
11/01/2005
0,1
2 4b000b5a01e00174 01000000436736a6 RESET_CELL
11/01/2005
0,1
2 4b000c3901e00175 01000000436736a6 CELL_POWER_OFF
11/01/2005
0
2 44800ee800e00176 00ffffffff01ff68 CELL_OFF
11/01/2005
0
2 4b000eca00e00178 01000000436736a6 IO_BP_LPM_OFF
11/01/2005
0
2 4b000ec700e00179 01000000436736a7 MAIN_BP_LPM_OFF
11/01/2005
0
2 4b000af800e0017a 01000000436736ad CABPWR_OFF
11/01/2005
0
2 4b000ec600e0017b 01000000436736ba MAIN_BP_LPM_GOOD
11/01/2005
0
2 4b000ec900e0017c 01000000436736ba IO_BP_LPM_GOOD
11/01/2005
0
2 44800ee700e0017d 00ffffffff01ff68 CELL_ON
11/01/2005
0,1
2 4b000b5801e0017f 01000000436736bb CELL_POWER_GOOD
11/01/2005
0,1
2 4b000b5a01e00180 0100000043673892 RESET_CELL
11/01/2005
0
2 44800ee800e00181 00ffffffff01ff68 CELL_OFF
11/01/2005
0,1
2 4b000c3901e00183 0100000043673892 CELL_POWER_OFF
11/01/2005
0
2 4b000eca00e00184 0100000043673893 IO_BP_LPM_OFF
1563
09:42:43
1564 MP
1564
09:42:43
1565 PM
1565
09:42:49
1566 MP
1566
09:43:02
1567 MP
1567
09:43:03
1568 MP
1568
09:43:03
1569 PDHC
1569
09:43:03
1570 PDHC
1570
10:31:14
1571 PDHC
1571
10:31:14
1572 MP
1572
10:31:14
1573 MP
1573
10:31:14
1574 MP
1574
10:31:15
1575 PM
1575
10:31:21
1576 MP
1576
10:31:38
1577 MP
1577
10:31:38
1578 MP
1578
10:31:39
1579 PDHC
1579
10:31:39
1580 PDHC
1580
10:41:08
1581 PDHC
1581
10:41:09
1582 MP
1582
10:41:09
1583 MP
1583
10:41:09
11/01/2005
0
2 4b000ec700e00185 0100000043673893 MAIN_BP_LPM_OFF
11/01/2005
0
2 4b000af800e00186 0100000043673899 CABPWR_OFF
11/01/2005
0
2 4b000ec600e00187 01000000436738a6 MAIN_BP_LPM_GOOD
11/01/2005
0
2 4b000ec900e00188 01000000436738a7 IO_BP_LPM_GOOD
11/01/2005
0
2 44800ee700e00189 00ffffffff01ff68 CELL_ON
11/01/2005
0,1
2 4b000b5801e0018b 01000000436738a7 CELL_POWER_GOOD
11/01/2005
0,1
2 4b000b5a01e0018c 01000000436743f2 RESET_CELL
11/01/2005
0,1
2 4b000c3901e0018d 01000000436743f2 CELL_POWER_OFF
11/01/2005
0
2 44800ee800e0018e 00ffffffff01ff68 CELL_OFF
11/01/2005
0
2 4b000eca00e00190 01000000436743f2 IO_BP_LPM_OFF
11/01/2005
0
2 4b000ec700e00191 01000000436743f3 MAIN_BP_LPM_OFF
11/01/2005
0
2 4b000af800e00192 01000000436743f9 CABPWR_OFF
11/01/2005
0
2 4b000ec600e00193 010000004367440a MAIN_BP_LPM_GOOD
11/01/2005
0
2 4b000ec900e00194 010000004367440a IO_BP_LPM_GOOD
11/01/2005
0
2 44800ee700e00195 00ffffffff01ff68 CELL_ON
11/01/2005
0,1
2 4b000b5801e00197 010000004367440b CELL_POWER_GOOD
11/01/2005
0,1
2 4b000b5a01e00198 0100000043674644 RESET_CELL
11/01/2005
0,1
2 4b000c3901e00199 0100000043674645 CELL_POWER_OFF
11/01/2005
0
2 44800ee800e0019a 00ffffffff01ff68 CELL_OFF
11/01/2005
0
2 4b000eca00e0019c 0100000043674645 IO_BP_LPM_OFF
11/01/2005
1584 MP
0
2 4b000ec700e0019d
1584
10:41:09
1585 PM
0
2 4b000af800e0019e
1585
10:41:15
1586 MP
0
2 4b001a6600e0019f
1586
00:00:31
1587 MP
0
2 4b000ec600e001a0
1587
02:55:35
1588 MP
0
2 4b000ec900e001a1
1588
02:55:35
1589 MP
0
2 44800ee700e001a2
1589
02:55:36
1590 PDHC 0,1
2 4b000b5801e001a4
1590
02:55:36
1591 PDHC 0,1
2 4b000b5a01e001a5
1591
03:01:58
1592 PDHC 0,1
2 4b000b5a01e001a6
1592
03:11:45
1593 SFW 0,1,0 *7 e38016dd10e001a7
FATAL_INTERRUPT_VECTOR
1593
04:23:09
1594 SFW 0,1,0 2 438016de10e001a9
FATAL_INTERRUPT_IIPA
1594
04:23:10
1595 SFW 0,1,0 2 438016df10e001ab
1595
04:23:10
1596 PDHC 0,1
2 4b000b5a01e001ad
1596
04:27:09
1597 SFW 0,1,0 *7 e38016dd10e001ae
FATAL_INTERRUPT_VECTOR
1597
04:29:36
1598 SFW 0,1,0 2 438016de10e001b0
FATAL_INTERRUPT_IIPA
1598
04:29:37
1599 SFW 0,1,0 2 438016df10e001b2
1599
04:29:37
1600 PDHC 0,1
2 4b000b5a01e001b4
1600
04:30:16
1601 PDHC 0,1
2 4b000b5a01e001b5
1601
06:27:51
1602 PDHC 0,1
2 4b000c3901e001b6
1602
06:27:51
1603 MP
0
2 44800ee800e001b7
0100000043674645 MAIN_BP_LPM_OFF
11/01/2005
010000004367464b CABPWR_OFF
11/01/2005
010000004368019f MP_TIMESTAMP
11/02/2005
0100000043682aa7 MAIN_BP_LPM_GOOD
11/02/2005
0100000043682aa7 IO_BP_LPM_GOOD
11/02/2005
00ffffffff01ff68 CELL_ON
11/02/2005
0100000043682aa8 CELL_POWER_GOOD
11/02/2005
0100000043682c26 RESET_CELL
11/02/2005
0100000043682e71 RESET_CELL
11/02/2005
0000000000005400
11/02/2005
00000727ff908910
11/02/2005
00000727ff908920 FATAL_INTERRUPT_IP
11/02/2005
010000004368401d RESET_CELL
11/02/2005
0000000000005400
11/02/2005
00000727ff908910
11/02/2005
00000727ff908920 FATAL_INTERRUPT_IP
11/02/2005
01000000436840d8 RESET_CELL
11/02/2005
0100000043685c67 RESET_CELL
11/02/2005
0100000043685c67 CELL_POWER_OFF
11/02/2005
00ffffffff01ff68 CELL_OFF
1603
06:27:51
1604 MP
1604
06:27:52
1605 MP
1605
06:27:52
1606 PM
1606
06:27:58
1607 MP
1607
06:28:11
1608 MP
1608
06:28:12
1609 MP
1609
06:28:12
1610 PDHC
1610
06:28:12
1611 PDHC
1611
06:35:18
1612 PDHC
1612
06:41:15
1613 PDHC
1613
06:54:17
1614 PDHC
1614
06:57:26
1615 MP
1615
00:00:30
1616 PDHC
1616
05:09:21
1617 PDHC
1617
05:16:16
1618 PDHC
1618
05:19:17
1619 PDHC
1619
05:21:58
1620 PDHC
1620
05:29:56
1621 PDHC
1621
05:38:35
1622 PDHC
1622
06:02:42
1623 PDHC
1623
06:28:55
11/02/2005
0
2 4b000eca00e001b9 0100000043685c68 IO_BP_LPM_OFF
11/02/2005
0
2 4b000ec700e001ba 0100000043685c68 MAIN_BP_LPM_OFF
11/02/2005
0
2 4b000af800e001bb 0100000043685c6e CABPWR_OFF
11/02/2005
0
2 4b000ec600e001bc 0100000043685c7b MAIN_BP_LPM_GOOD
11/02/2005
0
2 4b000ec900e001bd 0100000043685c7c IO_BP_LPM_GOOD
11/02/2005
0
2 44800ee700e001be 00ffffffff01ff68 CELL_ON
11/02/2005
0,1
2 4b000b5801e001c0 0100000043685c7c CELL_POWER_GOOD
11/02/2005
0,1
2 4b000b5a01e001c1 0100000043685e26 RESET_CELL
11/02/2005
0,1
2 4b000b5a01e001c2 0100000043685f8b RESET_CELL
11/02/2005
0,1
2 4b000b5a01e001c3 0100000043686299 RESET_CELL
11/02/2005
0,1
2 4b000b5a01e001c4 0100000043686356 RESET_CELL
11/02/2005
0
2 4b001a6600e001c5 010000004369531e MP_TIMESTAMP
11/03/2005
0,1
2 4b000b5a01e001c6 0100000043699b81 RESET_CELL
11/03/2005
0,1
2 4b000b5a01e001c7 0100000043699d20 RESET_CELL
11/03/2005
0,1
2 4b000b5a01e001c8 0100000043699dd5 RESET_CELL
11/03/2005
0,1
2 4b000b5a01e001c9 0100000043699e76 RESET_CELL
11/03/2005
0,1
2 4b000b5a01e001ca 010000004369a054 RESET_CELL
11/03/2005
0,1
2 4b000b5a01e001cb 010000004369a25b RESET_CELL
11/03/2005
0,1
2 4b000b5a01e001cc 010000004369a802 RESET_CELL
11/03/2005
0,1
2 4b000b5a01e001cd 010000004369ae27 RESET_CELL
11/03/2005
1624 PDHC
1624
06:34:10
1625 PDHC
1625
06:40:27
1626 PDHC
1626
07:03:28
1627 PDHC
1627
07:28:00
1628 PDHC
1628
08:32:56
1629 PDHC
1629
08:43:41
1630 PDHC
1630
09:03:33
0,1
2 4b000b5a01e001ce 010000004369af62 RESET_CELL
11/03/2005
0,1
2 4b000b5a01e001cf 010000004369b0db RESET_CELL
11/03/2005
0,1
2 4b000b5a01e001d0 010000004369b640 RESET_CELL
11/03/2005
0,1
2 4b000b5a01e001d1 010000004369bc00 RESET_CELL
11/03/2005
0,1
2 4b000b5a01e001d2 010000004369cb38 RESET_CELL
11/03/2005
0,1
2 4b000b5a01e001d3 010000004369cdbd RESET_CELL
11/03/2005
0,1
2 4b000b5a01e001d4 010000004369d265 RESET_CELL
11/03/2005
Rgds
ken
HI Mr Ken
Then you can use SEL, system error logs is the same with system event
logs but using different naming convention
FPL: Forward Progress Log
SEL: System Event Log
=========>>
LIVE: Live Events
Dear Chong
Mine is different. Exampe
CO:
VFP:
CM:
CL:
SL:
HE:
X:
Consoles
Virtual Front Panel (partition status)
Command Menu
Console Logs
Show Event Logs
Help
Exit Connection
[uninitialized] MP> sl
EVENT LOG MENU:
FPL: Forward Progress Log
SEL: System Event Log
LIVE: Live Events
CLR: Clear FPL and SEL
Q: Quit
[uninitialized] MP:VW>
HI Mr Ken
As per conversation, I'm now current researching on any issue with
RX7620 / MP card with Notebook Keyboard.
At the same time, please collect the following,
1.
Please collect the last / most recent 50 entries or dump the entire
error logs / SEL.
Control + B
MP> SL > E
Example:
CL: Console Logs
SL: Show chassis Logs ====>>
HE: Help
::
(A)ctivity Log
(E)rror Log
==========>>
(L)ive Chassis Logs
::
2.
Please try to reboot the server again and capture the exact message as
mentioned "Checking device"
::
::
If possible capture the whole print screen, thank you
I'll revert to you shortly
Regards
Chong