Super power
service Manual
www.genatamotor.eu
1
IMPORTANT
This manual was produced by the GENATA Holdings, Ltd. primarily for use by GENATA dealers
and their qualified mechanics. It is not possible to include all the knowledge of a mechanic in one
manual.
Therefore, anyone who uses this book to perform maintenance and repairs on GENATA vehicles
should have a basic understanding of mechanics and the techniques to repair these types of vehicles.
Repair and maintenance work attempted by anyone without this knowledge is likely to render the vehicle
unsafe and unfit for use.
This model has been designed and manufactured to perform within certain specifications in regard to
performance and emissions. Proper service with the correct tools is necessary to ensure that the vehicle
will operate as designed. If there is any question about a service procedure, it is imperative that you
contact a GENATA dealer for any service information changes that apply to this model. This policy is
intended to provide the customer with the most satisfaction from his vehicle and to conform to federal
environmental quality objectives.
www.genatamotor.eu
2
GENATA International Holdings, Ltd. is continually striving to improve all of its models. Modifications and
significant changes in specifications or procedures will be forwarded to all authorized dealers and will
appear in future editions of this manual where applicable.
TIP________________________________________________________________________________

This Service Manual contains information regarding periodic maintenance. Please read this
material carefully.

Designs and specifications are subject to change without notice.
IMPORTANT MANUAL INFORMATION
Particularly important information is distinguished in this manual by the following notations.
www.genatamotor.eu
3
PREFACE
Dear users：
Welcome to buy our Super Power. Sincerely we hope you could provide us with valuable comments and
suggestions while using our products. Your satisfaction is our greatest wish.
GENATA International Holdings Ltd. is a professional manufacturer of Power Technology. Super Power
bike is modern design, development, research and manufacture are ideal for a new generation of green
transportation which are original in appearance, comfortable for riding ,easy to operate, powerful, safe
with low noise, low maintenance cost advantages and a long cruising mileage. In order to make electric
bicycles better serve you, please read the instructions carefully before driving, and fully understand its
performance, use and maintenance of this e-bike, and then properly use it, exercise its best performance,
reduce failures and prolong its life.
Do not lend it to people who can not drive electric bicycles. Be strictly abided by traffic rules and drive
in the slow lane.
Ride slowly and keep the distance in rainy, snowy and in slippery road to ensure safety
Bag just to be used for storing helmets, chargers and other lightweight items (less than 3KG).
Prohibited to be stored heavy goods
www.genatamotor.eu
4
Due to the continuous improvements of this product, there are some difference between our product
and instruction. Please forgive us.
This manual is intended as a handy, easy-to-read reference book for the customer and mechanic.
Comprehensive explanations proposes solutions to technical problems, repair and check procedures
are laid out with the individual steps in sequential order.

The manual is divided into chapters and each chapter is divided into sections. The current
section title is shown at the top of each page.

Sub-section titles appear in smaller print than the section title.

To help identify parts and for the ordering of spare parts is an exploded diagramm available

Numbers are given in the order of the jobs in the exploded diagram. A number indicates a
disassembly step.
www.genatamotor.eu
5
675
www.genatamotor.eu
6
 Safe driving of matters need attention
Please obey the traffic rules, the speed control in
the safety speed. Please. (The highest safe
speed of this bike is 45KM/H)
Before driving, you should understand the
contents of this instruction manual, and then
find a empty safe field exercise, to fully grasp
the skill and familiar with its structure, which is
the basic safe driving.

Pay more attention to the rain and snow
weather driving on the road.

Rain and snow weather the ground is wet
and slippery dangers! Should avoid highspeed driving, steering to be especially
careful, encountered in advance braking, to
prevent accidental!

Properly qualified helmet, and fasten your
belt

To properly dressed:
Warning:
Dress color contrast, systemic activity freely, not
tight, cuff not open clothing, please do not wear
slipper or high heels driving vehicle
Do not lend it to people who can not
drive electric bike. Single and take off
the handlebar, drunk driving is
prohibited.
www.genatamotor.eu

7
Load capacity not too heavy
When loading or without loading, the vehicle
operation is different, and carrying too much,
will seriously affect the operation, prone to
danger. Allowable only one passenger, stored
bag rated load 3KG, do not exceed loading,
avoid driving safety hidden trouble and parts
damages
Attention

In order to facilitate the maintenance and service, each vehicle from our
company issued a unique frame number and motor number, ensures the dealer
to provide better service for you.

Frame number engraved on the direction of the vehicle frame pole on the right.
Motor number engraved on the body.

Electric Motor number engraved on the motor body.
www.genatamotor.eu
8
Super Power diagrammatic sketch
1.REAR VIEW MIRROR
2.HANDLEBAR
3.LEFT ASSEMBLE SWITCH
4.TURNING HANDLEBAR
5.FRONT BRAKE HANDLEBAR
6.LIGHTING SWITCH
7.REAR BRAKE HAND SHANK
8.STEERING UPPER CONNECTING PLATE
9.FRONT TURN INDICATOR
10.STEERING LOWER CONNECTING PLATE
11.STEERING LOCK
12.FRONT SHOCK ABSORBER
13.SIDE FLASHER
14.FRONT WHEEL RIM
15.FRONT WHEEL TYRE
16.FRONT FENDER
17.STORED BAG
18.FRONT FOOTREST
19.FRAME MAIN STAND
20.REAR FOOTREST
21.FORK
22.REAR DRUM BRAKE
23.REAR WHEEL RIM
24.REAR WHEEL
25.REAR FENDER
26.REAR SHOCK ABSORBER
www.genatamotor.eu
9
27.FOLDING FAST DISASSEMBLE
HANDLE
28.SEAT BRACKET
29.LICENSE PLATE BRACKET
30.REAR FLASHER
31.REAR INDICATOR
32.TAILLIGHT
33.SEAT
34.AIR SWITCH
35.CHARGER INTERFACE
36.MUSIC SYSTEM
37.SPEEDOMETER
38.HEADLIGHT
39.FRONT DISK BRAKE
40.FRONT BRAKE LOWER PUMP
41.SIDE STAND
42.SHIFT MOTOR ASSEMBLY
43.SUB-FRAME
Please identify the body were
marked in the figure the various
components, be familiar with the
vehicle
www.genatamotor.eu
10

SPEEDOMETER Function and Operation
1.STARTING LOCK
2.TEMPERATURE,TIME,KM/MILE INDICATION
3.SPEED 4.MAX SPEED
5.POWER AND VOLTAGEINDICATION
6.TOTAL MILEAGE 7.ONE TIME MILEAGE
8.SETECT PUSH-BUTTON INDICATOR
9.SETUP PUSH-BUTTON
10.TURNING INDICATOR
11.HIGH BEAM INDICATOR
12.FIRST GEAR
13.VOLTAGE TOO LOW INDICATOR
www.genatamotor.eu
11
Regional Function
1. Power door locks, running in the ON
position, the vehicle can be started the motor
and function of each part.
2. Is used to display the environment
temperature, time, and km / mile system
3.4. Respectively show the current speed and
the maximum speed driving
5. Display the remaining battery voltage and
current
6.7. Shows the total mileage and vehicle
mileage single
8.9. For adjusting and setting instruments
10. On turn signal, the indicator flashes
followed
11.Open beam headlamps, the indicator lights
along
12. When the vehicle is in a file, this
indicator lights
13.When the battery voltage is lower than
45V, the indicator lights
Meter adjustment and setup time：
 Two buttons for the "SELECT" and "SETUP"
button





Press the "SELECT" button for the
speedometer in kilometers / miles switch
Press "SETUP" button for the Single
odometer cleared
Press "SETUP" button for 2 seconds to enter
time setting function
Then you press the "SETUP" button to select
the setting items (current project will flash),
then press the "SELECT" button to change
the flashing item to adjust the value (long
press can quickly transform).
After setting a loop or long press "SETUP"
key to exit the settings

Switch operation
1.Turn on the switch, starting the motor and all
function of the vehicle; Turn off the switch, all
electrical source is cut off, then remove the key,
2.High & low beam switch, when open the head
light, Use this switch to change high and low
beam, up is high beam, down is low beam.
3.Turning light switch, when turning or change
road use the switch, the blinker flashs when use
the switch, press the middle button to stop, then
blinker crush out.
4.Horn switch
5. Light switch
Attention：
To avoid any misunderstanding, Please
stop the turning light after use.
www.genatamotor.eu
12

Accelerate Bar
Warning：
To avoid accident, please don’t use the
acceleration bar before driving, Please
remove the key immediately when stop
vehicle.
Remark:
The vehicle is automatic gear, only use
accelerate bar, no need other operation
5. Use and drive operation


Use the acceleration bar smoothly to accelerate
or decelerate, please don’t not use it roughly
Starting Method
Before starting: Check the vehicle is no
abnormity
1Put the key and turn to on position, then check
the switch, indicator, horn, and hold the Front &
Rear brake bar, check the brake and brake light
works.
 Brake operation
1. Please don’t use the acceleration bar when
brake.
2. To avoid tyre slip or any dangerous, Please
control the strength when brakes.
3. To avoid sideslip or any dangerous, Please do
not suddenly turn side or brake operation,
Especially raining weather.
2.Start E-Motor: when driver sit on the bike,
rise the side stander, Please operate the
acceleration bar smoothly
www.genatamotor.eu
Speed
13
Attention
Only use Fr. Brake or Rr. Brake may
cause sideslip


Parking
1. Take signal and indicator. Pay attention to the
rear, slow down the speed then close the parking
Drive notice
1. To ensure the safety of driver and vehicle,
save on battery for Endurance mileage, Please
keep smoothly drive, Do not hurry operation for
accelerate or decelerate
2. Pay attention for Rain or snow weather road
condition, please check the brake is works fine
and drive the vehicle at low speed,.
3. To ensure the controller safety, Please don't
drive the vehicle at heavy rain weather or road
gathered much water condition,
Notice:

To avoid the vehicle fall down, Do not
stop the vehicle at incline or soft place.
 Please lock the the vehicle and
steering and remove the key before
leave
 Do not caught in or swash the electric
parts.
place.
2. Use brake system to stop, turn off the indicator,
lock the vehicle then remove the key.
www.genatamotor.eu
14
3.After the vehicle stop, use the side stander to
park the vehicle.

4. Frequently charge would be health for lithium
battery.
Use and Maintenance of Battery
1.The vehicle use high performance 48V lithium
battery, It can be use temperature range -20℃to
50℃, best temperature is 10-30℃; Too over or
low temperature will effect the performance of
battery, Please do not charge the battery below
the temperature 0℃.
2. The performance like Endurance mileage
would be effected if temperature too low, It will
renew when temperature rise again,
5. Please keep 60% quantity of electricity and
turn off air lock when don't use the vehicle,
Charge the battery for each three month to avoid
effect the performance.

Charge and charger
1. Do not use other charger to avoid harm for
battery or any dangerous.
3. The battery have protect function to avoid
Warning
overcharge or Excessive discharge, but
Do not charge the battery below 0℃,
deepness discharge is harm for battery; please
charge the battery when the quantity of electric
charge lights on
www.genatamotor.eu
15
it will harm for battery
2. Check the input voltage is AC220V
3. You can both charge the battery or vehicle
directly.
Charging Notice
4. The right side picture is
the lithium battery, Black
for charge, Yellow for
discharge
5. When charging, the
Charger indicator will flash,
full charge is around 2-8
hours,( charger type 3A5A-8A)
6. The charger will turn off
automatic when battery
charged full, do not connect
the charger with electrified
wire netting, not more than
12 hours.
7.To avoid harm or dangerous, strictly prohibit
disassemble the battery by customer.
www.genatamotor.eu
16

Keep the charger in a safe place cannot
reach of children when charging.

Do not use the vehicle if the battery didn’t’t
charge full; Please use the vehicle after 10
minutes when charge full.

The charger can only use in dry and wellventilated place, do not cover anything
when charge

When charging, If the temperature is high
or can't charge full after a long time or
peculiar smell, Please stop charge and
send to maintain office.

Do not use others charger.

The charger is high voltage, Do not
disassemble it

It can be charge when lock the switch

Do not charge the battery billow 0℃

Prohibit to charge the vehicle when drive.
Use and Maintenance of Motor and Controller
1.Check the screw of the motor to avoid it is
loosen frequently
1.press red button to open the phone house.Do
not keep press the button for a long time.
2.IPHONE house can load IPHONE4 or 4S as
music player.
2.Check the connection wire between motor and
controller frequently.
3.Control Key：Sound source, Play/Pause,
Voice Up/Down, Next/Back.
3.Check the fuses frequently.(if it is
loosen,fasten or change it at once.)
4.Speaker：Do not touch the speaker with sharp
objects.
Use of MP3 and IPHONE Player
5.TF/MINISD card slot: support memory card as
sound source.
6.USB Connection, user can user USB disk to
be the music source. And also, user can use this
USB connection to charge the mobile phone. But
please do not connect the mobile phone, while
there’s the USB Disk connected.
A. SD Cart Input
B. USB Connect
The player support MP3 and IPHONE music
mode.
www.genatamotor.eu
17
INSPECTION BEFORE RIDING

TIRES INSPECTION
1. INSPECTION OF TIRES PRESSURE
According to the tires depression (The part
which touches the ground), users can judge
whether the tires pressure is normal. Generally
speaking, the normal tire pressure for front tire is
125Kpa,(1,25Bar) and the normal tire pressure
for rear tire is 175Kpa (1,75 Bar ) (If the tire
pressure is lower than the normal condition, the
speed and the riding distance per charge will be
affected).
2. Before riding, please check whether there’re
alligator cracks or abnormal wears on the tires,
3. Before riding, please check whether the tires
were damaged by the nails, sharp rocks, glasses,
etc
www.genatamotor.eu
18
4. Before riding, please check the tires tread
depth. If the tires tread depth is worn out 2/3,
then, users need to replace the old tires with
new tires.

INSPECTION OF SPEEDOMETER,
INDICATOR LAMPS, BRAKES
1. Open the electricity lock to check whether all
parts of the speedo meter are working in normal
condition.
2. Before riding, press the switches to see
whether the head light, indicator lamps, tail lamp,
horn work correctly.
3. Before riding, hold the right and left brake
handles to check whether the brakes work
correctly.
then, user need to replace the old tires with new
tires.
Warning
 It’s not safe to ride, when tires are
with abnormal pressures, damages,
and severe wears.



1.Open the electricity lock to check whether all
parts of the speedo meter are working in normal
condition.
When tires pressure is lower than
the normal condition, it will speed
up the tires wears, and cause the
steering failure happen, lower down
the speed, and shorten the riding
distance per charge)
2.Before riding, press the switches to see
whether the head light, indicator lamps, tail lamp,
horn work correctly.
3.Before riding, hold the right and left brake
handles to check whether the brakes work
correctly.
When tires pressure is higher than
the normal condition, it will also
speed up the tires wears, reduce
the riding comfort, and even cause
the tires blowout

INSPECTION OF REAR VIEW MIRRORS
1. Before riding, please check whether there
have some dirts or damages on the rear view
mirrors.
2. Before riding, please check the rear view
mirror from the riding position to see whether 2.
4. Before riding, please check the tires tread
depth. If the tires tread depth is worn out 2/3,
www.genatamotor.eu
INSPECTION OF SPEEDOMETER,
INDICATOR LAMPS, BRAKES
Before riding, please check the rear view
19
mirror from the riding position to see whether
riders can watch clearly about the situation at the
rear and two sides.


1.User stand at the left side of the vehicle, when
the vehicle is supported by the side stand. And
INSPECTION OF HANDLE BAR & SEAT
of the connection point
MOTORCYCLE FOLDING, BATTERY
TAKE-OUT & PUT-IN
www.genatamotor.eu
push the fast dismantling switch, which is
mounted at the right side
between the rear
absorber and the rear fork,
then, loosen the rear fork
to start the fast
INSPECTION OF VEHICLE FOLDING
STRUCTURE
Please check whether the rear fork and seat
bracket are mounted in the right positions, and
fix them tightly. Any problems found after the
inspection, user can try to solve the problems
according to the instructions in the users’ manual.
Or contact the dealer for after sales service.

MOTORCYCLE FOLDING
Before riding, please check whether there
have some dirts or damages on the
reflectors and the license plate.
Please check whether the handle bar & seat are
correctly fixed and adjusted in the right positions.


20
dismantling between rear
fork and rear absorber.
2. Right hand leaning on
the right side of the body
cushions and slightly to the
left side of the body force,
the left hand will be lifted up the rear shock,
quick-release lever from the flat fork, then lift the
rear bodywork, fork and rear wheel to a flat
before folding
3. Push the folding lock, which is positioned next
to the right foot rest, to lock on the locking screw
on the rear fork
4. Fold forward the
license plate support
bracket, then, loosen
downward the seat, until it’s
in the right position.
the fast dismantling
switch, which is
positioned at the
connection point
between the seat
support frame and the sub-frame. Meanwhile,
also loosen the nut at the left side of the fast
dismantling shaft
6. Push the locking plate,
which is positioned on the right side and middle
of the sub-frame, and press on the seat tightly to
lock the seat support bracket on the locking plate
to avoid the folded vehicle to unfold accidentally.
5. Move backward the entire fast dismantling
shaft, rotate downward the seat, and then, move
www.genatamotor.eu
forward the fast dismantling shaft to the original
position, push backward
the fast dismantling
switch to lock the seat.
After this, keep rotating
21
7. At last, retract the side stand. If the rear view
mirrors, which are chosen by the user, are
foldable rear view mirrors, user can fold the rear
view mirror to get a smaller folding size.
2. Push the seat folding locking plate, which is
positioned on the right side and middle of the
sub-frame, loosen the seat lock, and rotate the
seat upward.
Warning
 Before the folding, please switch
off the electricity lock to avoid any
accidents happen.


3. At the same time, push and loosen the seat
fast dismantling switch, move the entire fast
dismantling shaft backward, keep rotating the
seat upward, until it’s in a right position. Then,
move the fast dismantling shaft forward to the
slot of the sub-frame, tighten the nut of the fast
dismantling shaft, push back the fast dismantling
switch to lock the seat support bracket tightly.
When the motorcycle is folded,
user can push the vehicle forward.
But in this condition, start the
motor is prohibited. Otherwise, will
cause the damages to the vehicle,
or even hurts the user.
4. Unfold the license support bracket.
MOTORCYCLE UNFOLDING
Motorcycle’s unfolding steps are in the contras to
the motorcycle’s folding steps.
1. Open the side stand, unfold the rear view
mirrors.
www.genatamotor.eu
22
5. Push the rear fork folding lock plate, which is
positioned on the right side front foot rest, to
loosen the rear fork lock. And then, hold the rear
brake handle, move the motorcycle forward until
the side stand can stand on the ground.
6. User use the right hand to adjust the gradient
of the motorcycle, and use the left hand to put
the fast dismantling shaft into the slot of the rear
fork. Then, tighten the fast dismantling nut, Push
back and tighten the fast dismantling switch to
unfold to motorcycle.
2. Take off the charging and discharging plugs of
the battery, pull the battery backward to take out
the battery. Then, close the battery container,
and restore the bike folding.
Warning
 Please ride the motorcycle after
tighten all the fast dismantling
switches.



BATTERY PUT-IN
1. After the step 3 of the folding operation
finished, user can use the battery container cap
key to open the battery
container lock catch. Then,
pull the front of the lock
catch downward to open
the battery container cap.
The folding structure is very stable
and reliable. It does not affect the
motorcycle body intensity, and the
riding stability and safety.
2. Put the wire into the
longitudinal slot, which is
on the left side of the battery, and push the
battery into the container, meanwhile, make sure
the charging and discharging plugs are correctly
inserted. Then, close the battery container cap,
and make sure the battery container lock catch
is well locked. Finally, remove the key.
BATTERY TAKE-OUT
1. After the step 3 of the
folding operation finished,
user can use the battery
container cap key to open
the battery container lock
www.genatamotor.eu
catch. Then, pull the front of
the lock catch downward to
open the battery container cap, and the battery
can be seen.
23


REGULAR INSPECTION AND SIMPLE
MAINTENANCE METHOD
1. Choose the wide and flat ground to park the
vehicle.
2. When the user need to do the running
inspection, should lay it at a safety place, and
pay attention to the environment and situation
around the place at the same time.
Warning
 Please switch off the electricity
before the battery take-out or put-in.
Also turn off the air switch.
 If user cannot put-in the battery,
please do not try to put-in the battery
by force. Then, need to take-out the
batter to check whether the battery
is jammed by the bended wire.
3. If any unnormal problems were found in the
inspections, user must solve the problems first,
then, can ride the vehicle. If user cannot solve
the problems, can call the local dealer for
technical support, and then, solve to problem to
ride.
To increase the vehicle’s life time, ride with
safety and comfort, user need to do the regular
inspection for the motorcycle. If the motorcycle
has been not used for a long time, user also
need to do the regular inspection for the
motorcycle.
After the new Super Power run 300KM, need to
do inspection and maintenance.
www.genatamotor.eu
BE CAREFUL TO DO THE INSPECTION
24

INSPECTION FOR MAIN OPERATION
UNITS
1. Check the front absorbers to see whether any
bends, deformations and damages happened to
the front absorbers.
User need to check whether the front absorbers
have damages, loosen and oil leaking.
2. Rear absorber inspection.
Check the rear absorber to see whether any
bends, deformations, oil Leaking and loosen
happened to it. Meanwhile, user also need to
check whether the rear absorber is correctly and
tightly fixed.
not within this range, then, need to do
adjustments.
4. BRAKE EFFICIENCY AND INSPECTION
3. BRAKE INSPECTION
User can ride on the dry and plat road with low
speed, operate the front and rear brakes
separately to check the bake efficiency of each
brake.
User need to check whether the brake clearance
is within the range 15-20mm. If the test result is
If user do not have the suitable tools, please
send the motorcycle to the local maintenance
station to do inspection. In the condition of
Warning
 Front brake is disc brake. And when
the brake friction plates are worn to the
bottom of the groove mark, it needs to
be replaced with new friction plates.
 When the rear brake rock arm
indicating plate is worn to the bottom of
the groove mark, then, need to be
replaced with new rear brake friction
plate.
www.genatamotor.eu
25
lack of tools and skill, it’s prohibited that users
dismantle or assemble the Super Power.
Otherwise, the parts, or even the motorcycles
will get some damages.

TIRE INSPECTION
1. When the tires cool down, user can use the
tire pressure meter to check the tire pressure.
2.User must check whether there’re alligator
cracks, damages, sharp objects, abnormal
wears on the tires.
Usually, the tires will touch the ground for a long
time during the riding. And the sharp rocks,
broken glass pieces, nails, or any other sharp
objects will damage the tires. So, when users
ride on the road, please watch the road, and try
to avoid riding on the road, which is with a bad
condition and will cause damages to the tires.
And also, each time before the users ride the
motorcycle, the tires need to be checked to see
whether any obvious alligator cracks and
abnormal wears on the surface. Or the tires were
penetrated by sharp rocks, glass or some other
sharp objects.
3. TIRES TREAD DEPTH INSPECTION
Check the tires’ wear and tread depth. If the tires
tread depth is worn out 2/3, then, users need to
replace the old tires with new tires. During the
www.genatamotor.eu
26
riding, if users hear abnormal noise and found
strange shocks, please send the motorcycle to
the local dealer’s maintenance station to check.
Suggested tighten torque for the rear wheel axle
nut is 30NM, for the front wheel axle nut is 18NM.
Warning

Hold the left brake handle tightly, then,
if the brake does not have the ideal
brake effect, then, need to adjust the
nut of the rear brake cable.

If the front disc brake does not work
effectively, please check the front disc
plate’s cleanliness. If the brake still
does not work effectively, then, please
send the motorcycle to the local
dealers’ maintenance stations to check
and get the problems to be solved.
motorcycle to the local dealer’s maintenance
station to check.
Warning:

This motorcycle use enclosed lithium
battery, personally dismantling is
prohibited. Otherwise, will get the
battery to be damaged or cause any
dangers happen.
FUSE REPLACEMENT
After the air switch and electricity switch were
turned on, if all the lights and the horn do not
work, may be because the fuse was blown.
Before the users replace the fuse, please turn off
the air and electricity switches.
1. Open the upper cap of the sub-frame, pull out
and open the fuse box.

BATTEREY INSPECTION
The battery for this motorcycle is enclosed LiNiCoMn lithium battery, and need to use the
digital multi-meter to measure the positive and
negative voltage, after the battery is fully
charged. The voltage for the fully charged
battery should be within the range 53.5-54.6V. If
out of the range, then, need to send the
www.genatamotor.eu
27
2. Get the blown fuse off, and use the backup
fuse, which is fixed on the fuse box cap, to finish
the replacement. Then, well close the fuse box
and the upper cap of the sub-frame.
Technical Parameters and Specifications
External
dimensions
Folded size
Wheelbase
Overall vehicle
weight / Weight
including battery
Rated Load：
Maximum grade
ability：
Maximum speed：
1650X1100X650 mm
Warning
1045X1025X500 mm
1150 mm
41 Kg / 48Kg
150 Kg
≥18°（angle）
45 Km/h
Power Systems：
Two gear-shifts
automatic motor
Rated Power：
1500 W（Depending on
Maximum output
power：
the configuration）
2000-3000 W
（Depending on the
configuration）
www.genatamotor.eu
28
 The fuse must be tightly inserted, if
the insert parts are loosened, the
fuse maybe will be overheating to
cause other problems and
dangers happen.
 When the users replace the fuse,
must use the same size fuse
compared with the original fuse
on the motorcycle. Otherwise, the
fuse cannot work correctly to
protect the relative parts.
 If the new replaced fuse is blown
just after it’s inserted, users need
to check for other reasons.
 Must avoid strong water flow to
dash against the fuse part.
Driving wheel the
maximum torque：
Gear-shifts
method：
Gear-shifts
times ：
250 NM
Intelligence electronic
control instantaneous
drive
200 mS
Battery Type ：
Lithium ion battery
48V/16-28AH
Mileage one time
charging
55-80 Km（20AH
The charging time
2-8 h （Depending on
Charger input
voltage：
One hundred
kilometers charging
consumption：
Controller under
voltage：
Controller currentlimiting：
www.genatamotor.eu
Battery）
Battery the
overcorrect
protection value：
60A
Vehicle body
Type：
Type of wheel ：
Aluminum Alloy
Composite
Aluminum One Rims
1.85-14
Tubeless type 80/80-14
Hydraulic complex shock
absorber distance of
run:110mm
Hydraulic Complex
Center Shock Absorber,
Adjustable ,Distance of
Run:55mm
Disk Brake 180mm
Drum Brake 110mm
Type of tire：
The front
suspension
system：
Rear suspension
system
battery charger）
AC220V-50Hz
Front Brake system
Rear brake
system：
Headlamp
system：
Lights system：
Instrument Type：
2 KWH
40V
32A
29
AII LED Headlight 3W
AII LED Lightings 0.8W
AII LCD Speedometer
Folding
Music playback
system：
Stored Bag：
2 units fast folded M10
IPHONE/SD/TF/USB
AND MP3
Phone charging
interface
EVA nylon complex
waterproof
USB-5V Standard
Interface 500ma
Handlebar：
7075 Aluminum T6
www.genatamotor.eu
Product
Certification：
European standard
certification vehicles and
parts
Vehicle power /
weight ratio：
50W/Kg（General
electric car for about
15）
Note: Due to continuous product improvement,
performance parameters listed are subject to
change, in order to prevail in kind, without prior
notice
30
Trouble Symptoms and Remedies
NO
1
2
3
Symptom
Failure or a lower
maximum speed
governor
Meter Auto Zero
Power on, motor
does not work
www.genatamotor.eu
Failure
1. Battery voltage is too low
2. speed transfer to fail
1. button battery is exhausted
within the instrument
1. Loose battery cable
2. Speed transfer to joint shedding
3. Electrical wiring loose or fall off
4. Brake lever does not return or
the brake switch failure
31
Remedy
1. The battery is fully charged
2. Repair aftermarket for
replacement speed transfer
1. Replace the backup battery
1. Check the cable is securely
connected
2. 2 repair the plug is securely
connected
3. 3Maintenance Division reconnect and tighten
4. Check the brake lever and
brake switch
4
Lack of a single
charge endurance
mileage
1. Insufficient tire pressure
2. insufficient charging or charger
Error
3. improperly adjusted brakes,
driving resistance is too large
4. battery aging or damaged
5. more uphill, headwind, frequent
acceleration and deceleration,
containing significant
1. tire filled to the proper
pressure
2. fully charged or check the
charger plug contacts
3. re-adjust the brake
4. Replace the battery
5. The use of the environment
reduces battery life is
normal
5
The charger No
charge
1. charger plug off or loose
connections
2. loose battery cable plugs
6
Music player does
not work
1. source selection wrong
2. There is no memory card player
and other sources
3. The volume too low
7
Unusual ring
moving Vehicle
body
8
Other
1. quick release no fixed firmly
folded
2. Shock Absorber installation is
not stable or malfunction
1. When you encounter the above
1. Insert the plug or connector
2. Open the battery
compartment cover, Insert
the plug
1. Press the action key to
switch audio
2. Install the memory card or
U disk and other sources
3. Press the action key to
increase the volume
1. Adjust and tighten quick
release folding handle
2. Check whether the failure to
install and shock absorbers
In case of the above,
www.genatamotor.eu
32
malfunctions
can not be excluded under the
guidance of their own Error or
the fault can not be determined.
2. motors, controllers, chargers,
battery damage.
please contact your supplier or
service station, do not open the
above components, otherwise it
will lose our warranty.
Service and Warranty
Dear Users：
To better protect your interests, please take good care of this manual, when the Electric Scooter on the
spot inspection, testing, and require salesman to provide the correct methods of operation and
maintenance issues, provide effective notes, security cards and maintenance of address, contact phone.
When you use the vehicle, if meet some quality problems, based on purchase invoice and warranty card
to the company's dealer for warranty service.
Service and
www.genatamotor.eu
33
Original Spare Part Use
Warranty Contents
NO.
Names of Parts
1
Variable speed motor
assembly
2
Frame, fork flat
3
Controllers
4
Lithium Battery
www.genatamotor.eu
Quality problems
Broken gears, damaged line
group（other than human
factors）
Disordering, breaking（other than
human factors）
Malfunction can not be repaired
Insufficient capacity, quality
failures (ensure still intact
condition)
34
Warranty
period
Within
one year
Within
one year
Within
one year
Within
one year
These
component
failure during
the warranty
period, the
service does
not work
properly,
and a free
replacement.
5
Battery charger
6
instrument
7
shock absorbers
Oil spills, no damping
8
Speed twist grip, brake lever,
cable
Malfunction can not be repaired
（other than human factors）
9
Front and rear brakes, front
and rear wheels
Cracking, breakage, gas leakage
（other than human factors）
10
Electric door locks
Flasher, speakers, converters
Error（other than human
factors）
11
Side stand，direction
handles, pedals, plastic parts
Fracture（other than human
factors）
12
Baking varnish pieces
Paint off a large area（other than
human factors）
13
Lamps (including turn
signals, headlights, taillights)
Damage (other than human
factors)
www.genatamotor.eu
Malfunction can not be repaired
（other than human factors）
Malfunction can not be repaired
（other than human factors）
35
Within
one year
Within
six
months
Within
six
months
Within
six
months
Within
six
months
Within
three
months
Within
three
months
Within
three
months
Within
three
months
14
Music Player
Malfunction can not be repaired
（other than human factors）
15
Bag, cushions, rear view
mirrors
Damage (other than human
factors)
User's attention of report
1. Available against using the instructions on
Within
three
months
Within
three
months
Does not belong to the "three guarantees" the
scope and content.The user is not in accordance
with the "manual" of the requirement to use,
maintenance and adjustments caused by the
failure.
the warranty card to the sales office or our
authorized service stations for warranty
3. Users own overhaul and modification, as well
service
2. Our commitment: for E-Motor, Controllers,
Chargers, Lithium Batteries and other major
components, after a period of more than
three packs failure, maintenance only charge
as non-compliance with the provisions of
induced failure.
4. Users improper storage or accidents caused
by the failure
5. No warranty card, invoice or tickets, cards,
the amount of maintenance costs.
inconsistent things
www.genatamotor.eu
36
6. Wearing parts (brake cable, bearings, etc.)
consumables is not a "three guarantees"
range.
7. Over the warranty period
8. Collision, impact, overload and chemical
corrosion damage
9. Without special maintenance unit agreed to
repair
10. Has been compensation insurance company
www.genatamotor.eu
37
Warranty Card
Client Name
………………..
Address
Postal Code
…………………
Model
Super Power
Frame Number
Telephone NO.
Motor number
Sales Department
Telephone NO。
Customers signed and
stamp：
Date of purchase
Invoice number
Sales department
signed and stamp
Y
M
D
………………….
Y
M
D
…………………………
Spare Parts
Warranty Date
Warranty Record Card
Warranty Case Records
Warranty officers
and department stamp
Warranty Principles
"Three guarantees" and outside the scope of "three guarantees" after a period of service, the company will be responsible
for the warranty, and depending on the specific circumstances of fees charged for repair and replacement parts
www.genatamotor.eu
38
Spare Parts Catalogue
www.genatamotor.eu
39
Spare Parts Catalogue
www.genatamotor.eu
40
Spare Parts Catalogue
www.genatamotor.eu
41
Spare Parts Catalogue
www.genatamotor.eu
42
Spare Parts Catalogue
www.genatamotor.eu
43
Spare Parts Catalogue
www.genatamotor.eu
44
Spare Parts Catalogue
www.genatamotor.eu
45
Spare Parts Catalogue
www.genatamotor.eu
46
Spare Parts Catalogue
www.genatamotor.eu
47
Spare Parts Cat
www.genatamotor.eu
48
Spare Parts Catalogue
www.genatamotor.eu
49
www.genatamotor.eu
50
Europe Head Office
Asia Head Office
GENATA Motor Germany
GENATA International Holdings Ltd
Pettenkofer Str.8
NO. 801, Buildig 29, Jade-Green Island,
68169 Mannheim – Germany
Pu Nan Road, Hunag Pu Area
Guanzhou – CHINA
Email: [email protected]
Web: www.genatamotor.eu
www.genatamotor.eu
Email: [email protected]
51