126
Bosch Rexroth AG
Linear Bushings and Shafts
R310EN 3100 (2007.03)
Linear Sets with Torque-Resistant Linear Bushings, steel housing
Linear Sets, R1096 2..
Type 1: one ball guide groove
Linear Sets, R1096 5..
Type 2: two ball guide grooves
Structural design
– Precision steel housing
– Torque-Resistant Linear Bushing
– Precision Steel Shaft with ball guide
groove
– Torque-transmitting steel load bearing
plates adjusted to zero-clearance
before delivery
– External seals
– Stability against cocking loads:
see Linear Sets, Tandem version
Type 1: one ball guide groove
Shaft
Ød
(mm)
12
16
20
25
30
40
50
Part numbers Linear Set with shaft
Standard length
Shaft to specified
per table
length1)
R1096 212 80
R1096 212 89
R1096 216 80
R1096 216 89
R1096 220 80
R1096 220 89
R1096 225 80
R1096 225 89
R1096 230 80
R1096 230 89
R1096 240 80
R1096 240 89
R1096 250 80
R1096 250 89
Customized shaft
R1096 212 86
R1096 216 86
R1096 220 86
R1096 225 86
R1096 230 86
R1096 240 86
R1096 250 86
85 Shaft length 900 mm
87 Shaft length 1200 mm
88 Shaft length 2000 mm
Type 2: two ball guide grooves
Shaft
Ød
(mm)
20
25
30
40
50
Part numbers Linear Set with shaft
Standard length
Shaft to specified
per table
length1)
R1096 520 80
R1096 520 89
R1096 525 80
R1096 525 89
R1096 530 80
R1096 530 89
R1096 540 80
R1096 540 89
R1096 550 80
R1096 550 89
Customized shaft
R1096 520 86
R1096 525 86
R1096 530 86
R1096 540 86
R1096 550 86
85 Shaft length 900 mm
87 Shaft length 1200 mm
88 Shaft length 2000 mm
1) Also partly available with tubular shaft from shaft diameter 25: R1096 ... 69, or
with corrosion-resistant steel shaft per ISO 683-17 / EN 10088: R1096 ... 79.
R310EN 3100 (2007.03)
Linear Bushings and Shafts
Bosch Rexroth AG
127
Dimensions
C
M
C
T2
I
O
I
I2
I2
E e
T
J
Type 1
Type 2
F3
F2
Dimensions (mm)
Ød
Type 1 Type 2
B
H1
H1)
L
D
40
44
55
68
80
92
114
22
26
32
40
47
62
75
E1
E2
S2) S1
+0.013
–0.022
12
16
20
25
30
40
50
–
–
20
25
30
40
50
42 35
50 42
60 50
74 60
84
70
108 90
130 105
18
22
25
30
35
45
50
28 30 5.3 M6
30 36 5.3 M6
39 44 6.6 M8
48 54 8.4 M10
58 62 10.5 M12
64 80 13.5 M16
84 100 13.5 M16
Standard Torque
Load
Weight
length
capacity Mt
capacities3) (N) Linear Shaft
N
l
(Nm)
C
C0 Set
Type 1 Type 2
(mm)
(kg) (kg/m)
12
400
2
–
640
420
0.35
0.89
12
400
3.3
–
780
530
0.55
1.57
12
500
7.5
12
1550
1050
1.00
2.45
15
500
15
24 3030
2180
1.50
3.80
18
600
23
37 3680
2790
2.70
5.50
20
600
53
86 6320 4350
5.00
9.80
20
600
103
167 9250
6470
8.70 15.30
1) If two or more Linear Sets are mounted on the same shaft, they are leveled to the same dimension H by grinding after mounting.
Dimension H is then 0.5 mm smaller.
2) Mounting screws ISO 4762-8.8.
3) The load capacities stated are minimum values as the direction of load cannot always be precisely defined.
Determination of the dynamic load capacities is based on a travel life of 100,000 m.
Often only 50,000 m are actually stipulated. For comparison: Multiply values C from the table by 1.26.