Summary of proposals of Master Thesis themes
Proposals of Master Thesis
for Winter semestr in the academic year 2016/2017
- Mechanical Engineering postgraduate programme
- full time studies
No.
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
- International Design
Themes of theses
Number of
students
A heat storage for
1
improvement of operation
of domestic micro CHP
Numerical investigation
1
of the tunnel wall effect on
the flow around a solid body
Numerical prediction
1
of profile lift/drag
characteristics and
comparison with thin wing
theory
Effect of helical turbulators
1
on heat transfer
characteristics and
effectiveness
of double pipe heat
exchanger
Preliminary design of 1 MWe
1
biomass gasification power
plant
Design and CFD analysis
1
of a heat sink for use under
elevated temperature and
humidity conditions.
Numerical investigation
1
of the Magnus effect
of a spinning cylinder on the
lift to drag coefficient.
The theoretical analysis of
1
high temperature air
combustion process applied
in industrial boiler using CFD
software
Analysis and assesment of
1
mechanical ventilation heat
recovery unit
Oxidation of Zr alloy 1
influence of oxidation time on
alloy and oxide layer
microstructure
Oxidation of Zr alloy 1
influence of cooling
conditions on alloy and oxide
layer morphology
Engineering
Supervisor
Allotment criteria
Prof. dr hab. inż.
Dariusz Mikielewicz
Interview
Prof. dr hab. inż.
Jan Szantyr
Interview
Prof. dr hab. inż.
Jan Szantyr
Interview
Dr inż. Rafał Andrzejczyk
Interview
Dr inż. Marcin Jewartowski
High grade point
average
+Interview
Interview
Dr inż. Tomasz Muszyński
Dr hab. inż.
Krzysztof Tesch
Interview
Dr inż. J. Barański
High grade point
average
Dr inż. M. Wierzbowski
Interview
dr inż. H. Smoleńska
dr inż. H. Smoleńska
12.
13.
14.
15.
16.
17.
18.
19.
Application of the Rigid Finite
Elements Method in
Modeling and
Investigation of Dynamics of
Selected Radio Masts and
Towers Installed
at the Offshore Structures
Multibody Dynamics in
Modeling and Analysis of
Dynamics of a KUKA
KR150 robot
Experimental research of
flow in an orifices, in a short
pipes and in a throttle valve
Project of screw-in flow
restrictor valve
Influnce of tempering
temperature on hardness
and microstructure of
connection bolt material
Influence of temepreing time
on material hardness and
microstructure
Laser welding of structural
steels and evaluation of postwelding residual stresses
Analysis of fluid flow
structure in a butterfly valve
(this project is for one
student only.
1
dr hab. inż. K. Lipiński
1
dr hab. inż. K. Lipiński
1
Dr inż. Paweł Śliwiński
High grade point
average
1
Dr inż. Paweł Śliwiński
High grade point
average
1
dr inż. K. Krzysztofowicz
1
dr inż. K. Krzysztofowicz
2
Dr inż. Wojciech
Kiełczyński
1
Prof. T. Stolarski
Pre-requisites:
familiarity with
ANSYS/FLUENT
computer program at
the basic level)
Pre-requisites:
familiarity with
ANSYS/Mechanical
computer program at
the basic level)
20.
Modal analysis of a
suspension for a computer
hard disc drive (this project is
for one student only
1
Prof. T. Stolarski
21.
Flexible components for
compensation of
manufacturing inaccuracies
A concept project for a door
closer device with energy
harvesting function
Comparison of analytical
calculations of different pin
connection designs with FEM
analysis results
Design of mobile lift platform
for ultralight aeroplane used
in airdock
Comparative study of parts
manufacturing variants using
Design of Experiments
(DOE) method
Analysis of design schemes
for integrated process
planning and job scheduling
1
Dr J. Czyżewicz
1
Dr J. Łubiński
1
Dr. G. Rotta
1
Dr A. Olszewski
1
dr inż. Mieczysław
Siemiątkowski
possibly high
average grade of
dr inż. Mieczysław
Siemiątkowski
possibly high
average grade of
studies
22.
23.
24.
25.
26.
1
27.
28.
29.
30.
31.
32.
Total Preventive
Maintenance in chosen
manufacturing company.
Value Stream Mapping of
chosen manufacturing
process.
Algorithms for Computer
Aided Process Planning
based on Geometrical
Product Specification (GPS)*
Experimental determination
of recommended rotational
speeds of circular saw
blades
Cable tension control system
for rehabilitation devices
Balancing platform for
rehabilitation outcome
evaluation
1
dr inż. Aleksandra
Wiśniewska
1
dr inż. Aleksandra
Wiśniewska
1
dr hab. inż. Mariusz Deja
1
prof. dr hab. inż. Kazimierz
Orłowski, prof. nadzw. PG
Interview
1
dr inż. W.Sieklicki
Interview
1
dr inż. W.Sieklicki
Interview
possibly high
average grade of
studies
possibly high
average grade of
studies
Interview
*There is a possibility to change master thesis theme to the preference of student, when he picks one of
the supervisors theme and agree upon with supervisor.
** When more than one student will want to apply for the same Master thesis theme,
provides two choices
1. Master thesis theme will be assigned to student with the high grade point average.
2. Master thesis theme will be assigned to the student after interview