Certificate of Compliance
Certificate:
1874453 (LR 14496-12)
Master Contract:
150957
Project:
2435620
Date Issued:
June 23, 2011
Issued to:
Emerson Process Management
Valve Actuation LLC
13840 Pike Road
Missouri City, TX 77489
USA
Attention: Ken Wood
The products listed below are eligible to bear the CSA Mark shown
Joe da Silva
Issued by: Joe da Silva, C.E.T.
PRODUCTS
CLASS 3228 02
- VALVES - Actuators - For Hazardous Locations
Class I, Groups C and D; Class II, Groups E, F and G; Class III; Types 4X, 6P (as applicable); T4 or
T4A:
• Series 2000 Valve Actuators MCP and M2CP designs, with or without optional SCM and /or CBM or PBM or
MPA modules, rated 1/16 to 10 hp, 600V, 50/60Hz max, three phase, 240V, 50/60 Hz max, single phase or 250V
dc max; CBM or PBM modules as standalone assemblies, rated 480V, 0.5 to 67A and 115V, 10A respectively.
Class I, Groups B, C and D; Class II, Groups E, F and G; Class III; Temperature Coded T6; Types 4X,
6P:
• PBM Module, standalone assembly for use with Series 2000 Valve Actuators MCP and M2CP designs, rated
115 V, 10A.
Notes:
Notes:
1. Certified Conduit Seal(s) are installed between electrical enclosures.
Exception: Configurations of the Valve Actuators equipped with close coupled NPT threaded steel nipples
between electrical enclosures, instead of Certified Conduit Seal(s), are suitable for use in Class I, Group D;
Class II, Groups E, F and G; Class III Hazardous Locations.
DQD 507 Rev. 2009-09-01
Page: 1
Certificate:
1874453 (LR 14496-12)
Master Contract:
150957
Project:
2435620
Date Issued:
June 23, 2011
2 Electrical Motors used in the subject Valve Actuators are either the motors Accepted under CSA Report LR
14496-11 or, alternatively, the applicable Certified ones.
3. Motor thermal cut-off is Certified Texas Instrument, Temperature Coded T4 when valve actuator is protected
with (2) 130°C rated thermal cut-off; Temperature Coded T4A when valve actuator is protected with (2) 115°C
rated thermal cut-off.
4. Thermal cut-offs are pre-wired in series with motor contactor coil, at the factory.
5. Maximum ambient temperature: 60°C
6. Modules CBM and PBM include rating for Types 4X and 6P
APPLICABLE REQUIREMENTS
CSA Std C22.2 No. 0-M91 - General Requirements – Canadian Electrical Code, Part II
CSA Std C22.2 No. 14-95 Industrial Control Equipment
CSA Std C22.2 No. 25-1966 - Enclosures for Use in Class II Groups E, F, and G Hazardous Locations
CSA Std C22.2 No. 30-M1986 - Explosion-Proof Enclosures for Use in Class I Hazardous Locations
CSA Std CAN/CSA C22.2 No. 94-M91 - Special Purpose Enclosures
CSA Std C22.2 No. 139-1982 - Electrically Operated Valves
MARKINGS
• Submitter’s name;
• Model number;
• Electrical rating;
• Serial number;
• Enclosure Types 4X, 6P (as applicable);
• Hazardous Locations Designation:
Class I, Groups C and D; Class II, Groups E, F and G; Class III, for configurations with the Certified Conduit
Seal(s) between electrical enclosures.
Class I, Group D; Class II, Groups E, F and G; Class III, for configurations with close coupled NPT threaded
steel nipples, instead of Certified Conduit Seal(s), between electrical enclosures.
- PMP Module standalone: Class I, Groups B, C and D; Class II, Groups E, F and G, Class III, T6, Types 4X,
6P.
DQD 507 Rev. 2009-09-01
Page: 2
Certificate:
1874453 (LR 14496-12)
Master Contract:
150957
Project:
2435620
Date Issued:
June 23, 2011
• Temperature Code: T4 or T4A (as applicable); T6 for PBM stanalone Module.
• Caution Statements:
“Conduit seal is required at Electrical Enclosure Entrances“ - for all the configurations but standalone CBM or
PBM modules.
“Conduit seal is required within 18" of Entrances“ - for standalone CBM or PBM modules.
“Do not open cover while circuits are alive“ or equivalent.
“More than one live circuit. See Diagram“ or equivalent - for configurations that are energized from more than
one circuit and that do not have means for disconnecting all ungrounded conductors within single enclosure or
compartment.
• Ambient Temperature: 60°C maximum;
• CSA Monogram.
DQD 507 Rev. 2009-09-01
Page: 3
Supplement to Certificate of Compliance
Certificate:
1874453
Master Contract:
150957
The products listed, including the latest revision described below, are
eligible to be marked in accordance with the referenced Certificate.
Product Certification History
Project
Date
Description
2435620
June 23, 2011
2302193
May 14, 2010
2269380
1874453
January 29, 2010
April 4, 2007
Update to report 1874453 to cover use of MPA (Mulit-Port Actuator) module to
be used with Series 2000 valuve actuator M2CP.
Update of report 1874453 to include revised drawings and evaluation of minor
alternate construction
Reissue report 1874453 with new company name and address.
Update to report LR14496-12 to cover revised construction and add Class I,
Div. 1, Group B for Module PBM.
History
LR 1464096-12 April 28, 1998 Original Certification
Page: 1