Magtech Level Indicator
Configuration Data Sheet
December 2015
00806-0200-4430, Rev BA
Magtech™ GWR/MLI Dual Chamber Configuration
Data Sheet
 Select only one of the items provide
★ Default
 One or more of the listed items can be selected
General information
Company:_________________________________________________________
Phone No.: __________________________ Date: ________________________
Contact name:_____________________________________________________
RFQ No.:__________________________________________________________
Email: ____________________________________________________________
Tag:_____________________________________________________________
Process conditions
Pressure
Minimum:_________
Oper:_____________
Max:_____________
Units of measurement:_____________
Temperature
Minimum:_________
Oper:_____________
Max:_____________
Units of measurement:_____________
Description of media
___________________________________________________________________________________________________
Specific Gravity (SG)
Minimum:_________
Is the MLI indication for interface measurement?
If Yes
 Yes

 No

Lower fluid: min SG / max SG _____/_____
Upper fluid: min SG / max SG _____/_____
Dielectric constant ___________
Dielectric constant ___________
Does media flash or outgas in chamber?
Is this a saturated steam application?
 Yes
 Yes


 No
 No


Customer-specific design criteria
Are there any existing specifications, including minimum pipe schedule, general piping specifications, or an approved manufacturer list (AML/AVL) to which this these
chambers must comply
 Yes (please provide)  No
Transmitter:
Model:
 Guided-wave radar
 Non-contacting radar
 None
Transmitter output:
Transmitter options:
 4/20 mA and
 FOUNDATION™ Fieldbus (5300/5400 only)
 Modbus®
 Wireless (3308)
 SIL Certification
 Remote housing (specify cable length)
 Transient protection
 1m  2m  3m
 LCD display
 Hazardous area approval (specify):__________________________________
HART®
Mounting style
Select Style:
Orientation (top view)
Choose process
connection location
Choose indicator/scale
location
Right hand
Mounting
dimension
Standard
Left hand
Magtech Level Indicator
December 2015
Material of construction
Process connection type
 316/316L SS
 316/316L SS pipe with carbon steel flanges
 Other non-magnetic material: _________________
 RFSO
 RFWN
 RFSW
Flange rating
 RFLJ
 RTJWN
 NPTM
 NPTF
 Socket weld fitting
 Plain end nipple fitting
 Other ______________
Process connection size (inch)
 150#
 900#
 300#
 1500#
 600#
 Other: ________
Vent valve (Optional)
Vent
Type
 1/2
 11/2
Type
Type





OR


Type

 Ball
 Flange
 Gate
 SW
 Other ______________
 Other: ___________ Material
Size (inch)
 Carbon steel
1
★
 Stainless steel
 /2
3
 /4
Valve notes:____________
1
NPT★

1
 Other: ______________
Drain valve (Optional)
Drain

 Ball
 Flange
 Gate
 SW
 Other ______________
 Other: ___________ Material
Size (inch)
 Carbon steel
1
★
 Stainless steel
 /2
3
 /4
Valve notes:____________
1
NPT★
 3/4
2








Indicator type:
Flags colors (if applicable):
Scale units of measure
 Flags with scale★
 Follower with scale
 Red/silver ★
 Red/white
 Yellow/black
 Feet & inches★
%
 Inches only
 Metric (5 cm increments)
 +/ Other (please specify): ______________
All item below are OPTIONAL
Accessories
Tests and inspections
 Level switches
Qty: ___________ Amp:  1-amp  10-amp
 Pneumatic switch Qty ___________ Action:  Rising  Falling
 Insulation blanket
 Heat tracing (no controller)
 Cryogenic insulation
 Stream tracing
 PMI
 X-Ray
 Hydrostatic test
 NACE MR0103
 Dye pen
 NACE MR0175
 CRN, specify province: _____________________





Documentation:
 Material Traceability Report (MTR)
 Drawings
 Approval  As-built
Other special request (describe or provide sketch)
2


 Country of origin
 Certificate of conformance
 Calibration certificate (for GWR)
Magtech Level Indicator
00806-0200-4430, Rev BA
Configuration Data Sheet
December 2015
Global Headquarters
Emerson Process Management
6021 Innovation Blvd.
Shakopee, MN 55379, USA
+1 800 999 9307 or +1 952 906 8888
+1 952 949 7001
[email protected]
North America Regional Office
Emerson Process Management
8200 Market Blvd.
Chanhassen, MN 55317, USA
+1 800 999 9307 or +1 952 906 8888
+1 952 949 7001
[email protected]
Latin America Regional Office
Emerson Process Management
1300 Concord Terrace, Suite 400
Sunrise, FL 33323, USA
+1 954 846 5030
+1 954 846 5121
[email protected]
Europe Regional Office
Emerson Process Management Europe GmbH
Neuhofstrasse 19a P.O. Box 1046
CH 6340 Baar
Switzerland
+41 (0) 41 768 6111
+41 (0) 41 768 6300
[email protected]
Asia Pacific Regional Office
Emerson Process Management Asia Pacific Pte Ltd
1 Pandan Crescent
Singapore 128461
+65 6777 8211
+65 6777 0947
[email protected]
Linkedin.com/company/Emerson-Process-Management
Middle East and Africa Regional Office
Emerson Process Management
Emerson FZE P.O. Box 17033
Jebel Ali Free Zone - South 2
Dubai, United Arab Emirates
+971 4 8118100
+971 4 8865465
[email protected]
Standard Terms and Conditions of Sale can be found at:
www.Emerson.com/en-us/pages/Terms-of-Use.aspx
The Emerson logo is a trademark and service mark of Emerson Electric Co.
FOUNDATION Fieldbus is a trademark of the FieldComm Group.
HART is a registered trademark of the FieldComm Group.
Magtech is a trademark of Emerson Process Management.
Modbus is a registered trademark of Gould Inc.
All other marks are the property of their respective owners.
© 2015 Emerson Process Management. All rights reserved.