Product data sheet
Sheet No.: 1.606.01 - Rev: C Page 1 of 2
Date:
May 2014
FieldQ
FieldQ valve actuator
Parts and materials Actuator and Modules
Description
Body
Pinion
Upper pinion part
Guide band housing
Washer pinion
Bearing ring
Limit stop cam
Piston
End cap QS
End cap QD
Guide band piston
O-ring piston
O-ring end cap
O-ring upper pinion part
O-ring pinion top
O-ring pinion bottom
O-ring B-port
O-ring retainer bolt
O-ring limit stop bolt
Outer spring
Middle spring
Inner spring
Spring retainer
Washer spring pack
Spring pack retainer bolt
Washer
Nut
Nut cover
End cap screws
Retaining ring pinion large
Retaining ring pinion small
Limit stop screw
Indicator cap
Indicator arrow
Indicator insert
Type plate
Hammer drive
Insert
Qty. Description
1
Aluminum Alloy
1
Aluminum Alloy
1
Aluminum Alloy
2*
Nylatron
2*
CRMZX100
2*
Delrin®
1
Steel
2
Aluminum Alloy
2
Aluminum Alloy
2
Aluminum Alloy
2*
PTFE, Carbon filled
2*
Nitrile Rubber
2*
Nitrile Rubber
1*
Nitrile Rubber
1*
Nitrile Rubber
1*
Nitrile Rubber
2*
Nitrile Rubber
4*
Nitrile Rubber
2*
Nitrile Rubber
2
Carbon Spring Steel
2
Carbon Spring Steel
2
Carbon Spring Steel
2
Steel
2
Steel
2
Stainless Steel
4*Nylon
4
Stainless Steel
2
Polyethylene
8
Stainless Steel
1*
Carbon Spring Steel
1*
Carbon Spring Steel
1
Stainless Steel
1
Nylon
1
Nylon
1
Nylon
1
Stainless Steel
1
Stainless Steel
1
Aluminum Alloy
Specification
EN AC-AlSi10Mg (Cu)
EN AW 7075 T6
EN AW 7075 T6
PA6.6 + MoS2
-
POM
42CrMo4V
EN AC-AlSi7Mg
EN AC-AlSi7Mg
EN AC-AlSi7Mg
PTFE + 25% C
NBR
NBR
NBR
NBR
NBR
NBR
NBR
NBR
EN 10270-1 SH
EN 10270-1 SH
EN 10270-1 SH
St. DC01 EN10139
C35
AISI 304 (DIN W nr 1.4301)
PA6
AISI 304 (DIN W nr 1.4301)
PE
AISI 304 (DIN W nr 1.4301)
C45, DIN 17200
C45, DIN 17200
AISI 304 (DIN W nr 1.4301)
PA6
PA6
PA6
AISI 303 (DIN W nr 1.4305)
AISI 303 (DIN W nr 1.4305)
EN AW 6082 T5
Notes
1/5
2
2
6
1
1
3
3
3
4
4
3
3
5
Notes
1 See Corrosion protection below
2 Hard anodized.
3Deltatone® or Epoxy (black) coating.
4 Zinc plated and passivated.
5Anodized.
6Chromatized
Control & Pneumatic Modules
www.FieldQ .com
Copyright © Emerson Process Management. The information in this document is subject to change without notice. Updated data sheets can be obtained
from our web site www.Fieldq.com or from your nearest Valve Automation Center:
America’s: +1 281 477 4100 (fax 477 2809) Europe: +31 74 256 10 10 (fax +31 74 291 09 38) Asia/Pacific: +65 650 14 600 (fax +65 626 80 028)
For material specification of
the Pneumatic Modules see
page 2
Corrosion protection
The applied paint system
has passed a 1000 hour salt
spray test as detailed by
ASTM B117. For a detailed
description of the Corrosion
protection system see data
sheet 1.606.05.
Temperature ranges
The temperature range
of FieldQ actuators with
NAMUR plates depends
on the O-ring seals and the
utilized grease.
For a detailed description of
posible temperature ranges
and applied parts, see data
sheet 1.605.03
Repair kit
Parts marked with an * are
included in the repair kit
Product data sheet
Sheet No.: 1.606.01 - Rev: C Page 2 of 2
Date:
May 2014
FieldQ
FieldQ valve actuator
Parts and materials Actuator and Modules
Modules QC01, 02, 03, 04
Modules QC41, QC42, QC43
QC11, QC12, QC13, QC14
QC30, QC31 and QC34
6
3
1
2
3
1
2
4
5
Base Materials
Body:Aluminium
Valve housing:
30% glass-filled Nylon
Finish:
Polyester non-TGIC based powder
coating
Valve seats:
Buna-N
Membrane:Buna-N
Fasteners:
Stainless Steel
External parts
1 Plug
NPT:
BSP:
2 Vents:
3 Exhaust
Base: Cover:
Option:
4 Speed Control:
- Throttle:
- Nut Cover:Nylon
5 Plug:
6 Manual Control:
- Plug: - Push:
- Push & Lock: Steel, zinc plated
Brass, nickel plated
Stainless Steel (AISI 303)
Nylon
Zinc Nickel plated and transparent passivated
Plastic silencer (nylon)
Stainless Steel (AISI 303)
PA6
Brass Nickel plated
4
Base Materials
Bodies:Aluminium
Finish:
2 Component with an epoxy primer and
polyurethane enamel top coating.
Pneumatic cartridge:
Aluminium
Valve seats
NBR
Pilot valve cartridge:
Housing: Nylon PA6
Switch cartridge:
Housing: Nylon PA6
Fasteners
Stainless Steel
External parts
1 Plug
2 Exhaust
NPT:
Base :
Cover:
Steel, Nickel plated
Nylon PA6
Zinc, Nickel plated and transparent passivated
Option: Plastic silencer (nylon)
3 Speed Control:
Stainless Steel (AISI 303)
4 Manual Control:
Red anodized aluminum
5 Nut Covers: Nylon PA6
Brass Nickel plated
Red anodized aluminum
Red anodized aluminum
www.FieldQ .com
Copyright © Emerson Process Management. The information in this document is subject to change without notice. Updated data sheets can be obtained
from our web site www.Fieldq.com or from your nearest Valve Automation Center:
America’s: +1 281 477 4100 (fax 477 2809) Europe: +31 74 256 10 10 (fax +31 74 291 09 38) Asia/Pacific: +65 650 14 600 (fax +65 626 80 028)