CH. ORDER
ORIGINAL SIZE
FIELDBUS INTRINSICALLY SAFE CONCEPT (FISCO) APPROVAL
FISCO allows
of intrinsically safe apparatus to associated apparatus not specially examined
in such combination. The criteria for interconnection is that the voltage (Ui or Vmax), the current
or
and the power (Pi or
which an intrinsically safe apparatus can receive and remain intrinsically safe
considering faults, must be equal or greater than voltage (Uo, Voc or Vt), the current (lo,
or It) and
the power (Po or Pmax) levels which can be delivered by the associated apparatus, considering faults
and applicable factors. In addition, the maximum unprotected capacitance (Ci) and the inductance (Li) of each
apparatus (other than the termination) conncected to the Fieldbus must be less than or equal to 5 nF and
uH respectively.
In each l.S. Fieldbus segment only one active device, normally the associated apparatus, is allowed to
provide the necessary energy for the Fieldbus. The voltage (Uo, Voc or Vt) of the associated apparatus is
limited to a range of 14 V to 17.5 V. In this instance Rosemount
has voltage as given in table below.
All other equipment connected to the bus cable has to be passive, meaning that they are not
allowed to provide energy to the system, except a leakage current of 50 uA for each connected device.
Separately powered equipment needs galvanic isolation to assure that the intrinsically safe Fieldbus circuit
remains passive.
CH. ORDER No
CH. ORDER No
CH. ORDER No
ROSEMOUNT 2410 FISCO POWER SUPPLY
US/Canada
Ex de[ib]
Gb T4
ATEX
C L I ZONE 1
depb]
II 2(2)G Ex depb] IIB T4
to
Installation Notes:
FISCO allows the interconnection of Approved intrisically safe devices with FISCO
parameters not specifically examined in combination as a system when:
Uo, Voc or Vt =< Ui or Vmax, lo, Ioc or It =< or
Po =< Pi or Pmax
FISCO Parameters:
Uo =
V; lo = 354
Po = 5.32 W
2. Control equipment connected to the Associates Apparatus must not use or generate more than
250
VDC.
The cables used to interconnect devices need to have the parameters in the following range:
3. Dust tight conduit seals must be used when installed in Class ll and Class III environments.
Loop Resistance Rc:
Loop Inductance
Capacitance per unit length
2015-07-07 Electronic Master - Printed Copies Uncontrolled - Emerson Proprietary
Length of trunk cable:
Length of spur cable:
15
150 ohm/km
0.4 1 mH/km
45
200 nF/km
Cc=Cc line to line + 0.5
line to screen, if both lines are floating or
Cc=Cc line to line + Cc line to screen, if screen is conncted to one line
Less than or equal to 1 km for
(5km for
Less than or equal to 60
At each end of the trunk cable an approved infallible line terminator with the following parameters should be installed:
R >=90 ohm, C <=2.2 uF (recommended parameters are:
ohm, C=1.0 +/-0.2 uF)
One of the allowed terminations might already be integrated in the associated apparatus. Rosemount
is
equipped with integrated termination, see note 7.
4. Earth connection. Minimum cable area 4 mm2
5. Field Apparatus manufacturers installation drawing must be followed when installing this equipment.
6. Installation in the USA should be in accordance with
"Installation of Intrinsically
Safe Systems for Hazardous (Classified) Locations" and the National Electrical Code
70).
7. It is possible to disconnect the integrated termination by means of a jumper located inside
Rosemount
The ENTITY CONCEPT allows the interconnection of Approved intrisically safe devices with ENTITY
parameters not specifically examined in combination as a system when:
Uo, Voc or Vt =< Ui or Vmax, lo, Ioc or It =< or
Po =< Pi or Pmax.
FISCO limits the number of passive devices connected to a single segment to 32 devices. If the above rules are
respected, up to a total length of 1000
(sum of trunk and spur cables) of cable is permitted. The inductance and
capacitance of the cable will not impair the intrinsic safety of the installation.
ENTITY CONCEPT APPROVAL
The Entity concept allows interconnection of intrinsically safe apparatus to associated apparatus not specifically
examined in combination as a system. The approved values of max. open circuit voltage (Uo, Voc or Vt), max.
short circuit current (lo,
or
and max. power (Po or
/ 4 or
/
for the associated apparatus must
be less than or equal to the maximum safe input voltage (Ui or Vmax), maximum safe input current
or
and
maximum safe input power (Pi or Pmax) of the intrinsically safe apparatus. In addition, the approved max.
allowable connected capacitance (Co or Ca) of the associated apparatus must be greater than the sum of the
interconnecting cable capacitance and the unprotected internal capacitance (Ci) of the intrinsically safe
apparatus, and the approved max. allowable connected inductance (Lo or La) of the associated apparatus must
be greater than the sum of the interconnecting cable inductance and the unprotected internal inductance (Li) of the
intrinsically safe apparatus.
ISSUED BY
WEEK
PRODUCT CODE
APPROVED BY
WEEK
DOC. TYPE
EE-VN
EAp
WARNING - Substitution of components may impair Intrinsic Safety.
WARNING - To prevent ignition of flammable or combustible atmospheres,
disconnect power before servicing.
0844
2410
6
ALL DIMENSIONS ARE IN MILLIMETRES.
TOLERANCES. UNLESS OTHERWISE
STATED:
FM Approved Product
No revision to this drawing
without prior Factory Mutual
Approval.
o
o
FILE
OrCADl
S Y S T E M C O N T R O L DWG.
ROSEMOUNT 2410
1 /8
9240040-901
1 ST ANGLE
The copyright/ownership of this document is and will remain ours.
The document must
be used without our authorization or brought
to the knowledge of a third party. Contravention will be prosecuted.
Rosemount
Tank RadarAB,
Sweden
ISSUE
ORIGINAL SIZE
NON-HAZARDOUS
AREA
CH. ORDER No
WEEK
ISSUE
1
CH. ORDER No
2
WEEK
ISSUE
CH. ORDER No
1113 | 3
WEEK | ISSUE
CH. ORDER No
WEEK
HAZARDOUS AREA
NON-HAZARDOUS OR ZONE 1 / DIVISION 1 HAZARDOUS AREA
2015-07-07 Electronic Master - Printed Copies Uncontrolled - Emerson Proprietary
OPTIONAL
INTRINSICALLY
SAFE
UNSPECIFIED
CONTROL
EQUIPMENT
(Note 2)
ANY
APPROVED
FISCO FIELD
DEVICE
NON IS
APPROVED
FISCO
TERMINATOR
FM Approved Product
No revision to this drawing
without prior Factory Mutual
Approval.
BY
EE-VN
APPROVED BY
CT)
EAp
WEEK
PRODUCT CODE
WEEK
DOC. TYPE
0844
2410
6
FILE
OrCADl
ALL DIMENSIONS ARE IN MILLIMETRES.
TOLERANCES. UNLESS OTHERWISE
I STATED:
o
CM
G)
S Y S T E M C O N T R O L DWG.
ROSEMOUNT 2410
(INSTALLATION OVERVIEW)
9240040-901
1 ST ANGLE
2 / 8
The copyright/ownership of this document is and will remain ours.
The document must not be used without our authorization or brought
to the knowledge of a third party. Contravention will be prosecuted.
Rosemount
Tank
Sweden
ISSUE
ORIGINAL SIZE
NON-HAZARDOUS
AREA
Signal
N/ +
K1 A
COM
K2A
K2 COM
P
B
P BUS A
+
X1
Terminal
1
2
3
4
5
7a
7b
8a
8b
9
10
11
2015-07-07 Electronic Master - Printed Copies Uncontrolled - Emerson Proprietary
12
POWER
SUPPLY
(24/48 VDC,
48, 65 and
50/60Hz)
CH. ORDER No
WEEK
ISSUE
1
CH. ORDER No
2
1113
ISSUE
CH. ORDER No
CH. ORDER No
3
NON-HAZARDOUS OR ZONE 1 / DIVISION 1 HAZARDOUS AREA
HAZARDOUS AREA
Data
Signal
Power, Neutral / DC Power.
+
Relay 1 output (optional)
FB +
FB +
FBFB-
single terminals)
Relay 1 common
Relay 2 output (optional)
Relay 2 common
Primary comm. Bus
Primary comm. Bus
Primary comm. Bus
Primary comm. Bus
Secondary
(optional)
Secondary Power +
(optional)
Secondary comm. Bus
[optional)
Secondary comm. Bus
(optional)
X2
Data
Terminal
1a
1b
2a
2b
3
4
5
6
TankBus +
TankBus +
TankBus Future
Future
Future
Future
option
option
option
option
PE
VAC, N / |_ / +
Relay output
(Option)
K1 A
K1 COM
K2 A
K2 COM
Primary
Communication Bus
P BUS B
P BUS A
Secondary
Communication Bus
(Option)
ATEX /
Zone 1
US / Canada: Division 1 or Zone 1
Tank Bus
FISCO POWER SUPPLY
Note
see sheet 1
S PWRS PWR +l
S BUS B
S BUS A
FM Approved Product
No revision to this drawing
without prior Factory Mutual
Approval.
ISSUED BY
WEEK
PRODUCT CODE
APPROVED BY
WEEK
DOC. TYPE
EE-VN
Shielded cable
Optionally shielded cable
0844
2410
EAp
6
ro ALL
DIMENSIONS ARE IN MILLIMETRES.
•
o
o
o
CM
CD
FILE
OrCADl
S Y S T E M CONTROL DWG.
ROSEMOUNT 2410
(BASIC)
TOLERANCES, UNLESS OTHERWISE
STATED:
1 ST ANGLE
ISSUE
9240040-901
3
SHEET
3 /8
The copyright/ownership of this document is and will remain ours.
The document must not be used without our authorization or brought
to the knowledge of a third party. Contravention will be prosecuted.
Rosemount
Tank
Sweden
ISSUE
ORIGINAL SIZE
1
NON-HAZARDOUS
AREA
Signal
/ -
K1 COM
K2 A
K2
Q
P BUS B
ALARM B
ALARM A
1
2
3
4
5
S
7a
7b
8a
8b
9
10
11
12
WEEK
ISSUE
CH. ORDER No
2
SME-6989
WEEK
1113
ISSUE
3
NON-HAZARDOUS OR ZONE 1 / DIVISION 1 HAZARDOUS AREA
WEEK
ISSUE
CH. ORDER No
WEEK
HAZARDOUS AREA
X2
Data
Terminal
(Optional single terminals)
FB
FB
FB
FB
+
+
-
1a
1b
2a
2b
3
4
5
6
Alarm +
comm. Bus
Primary comm.
Not used
Not used
SIL relay common
SIL relay output NO
TankBus
TankBus
TankBus
TankBus
+
+
-
Future option
Future option
SIL alarm SIL alarm +
PE
ATEX/IECEx: Zone 1
US / Canada: Division 1 or Zone 1
VAC, N / -
L/ +
Relay output
(Option)
K1 A
K1 COM
K2 A
K2 COM
Primary
Communication Bus
P BUS B
P BUS A
SIL Alarm Relay
CH. ORDER No
SME-8259
Signal
Pov/er. Neutral DC Power. Line /
Relay 1 output (optional)
Relay 1 common
Relay 2 output (optional)
Relay 2 common
comm. Bus
POWER
SUPPLY
(24/48 VDC,
4 8 , 65 and
50/60Hz)
2015-07-07 Electronic Master - Printed Copies Uncontrolled - Emerson Proprietary
SME-6096
Data
L/ +
D
CH. ORDER No
Alarm +
Alarm -
Note
see sheet 1
Tank Bus
FISCO POWER SUPPLY
Note 1, see sheet 1
ALARM B
ALARM A
FM Approved Product
No revision to this drawing
without prior Factory Mutual
Approval.
ISSUED BY
EE-VN
Shielded cable
Optionally shielded cable
APPROVED BY
Oi EAp
o
o
0844
WEEK
PRODUCT CODE
2410
DOC. TYPE
6
FILE
OrCADl
ALL DIMENSIONS ARE IN MILLIMETRES.
TOLERANCES, UNLESS OTHERWISE
STATED:
S Y S T E M CONTROL DWG.
ROSEMOUNT 2410
(SIL OPTION)
1 ST
ISSUE
9240040-901
3
SHEET
4
The copyright/ownership of this document is and will remain ours.
The document must not be used without our authorization or brought
to the knowledge of a third
Contravention
be prosecuted.
Tank
Sweden
A3
ISSUE
1
NON-HAZARDOUS
AREA
CH. ORDER No
WEEK
1029
ISSUE
CH. ORDER No
2
SME-6989
WEEK
1113
ISSUE
3
CH. ORDER No
NON-HAZARDOUS OR ZONE 1 / DIVISION 1 HAZARDOUS AREA
Signal
K1 COM
K2A
K2 COM
P BUS B
P BUS A
P BUS A
1
2
3
4
5
S
Ta
7b
8a
8b
Power. Neutral / DC Power, Line / DC +
Relay 1 output
Relay 1 common
Relay 2 output (optional)
Relay 2 common
Primary comm. Bus
Primary comm. Bus
Primary comm. Bos
Primary comm.
Secondary Power (optional)
10
Secondary Power +
[optional)
Secondary comm. Bus
(optional)
Secondary comm. Bus
(optional)
11
S
A
12
ISSUE
CH. ORDER No
single terminals)
X2
Data
Terminal
FB +
FB +
FBFB-
1a
TankBus +
TankBus +
TankBus TankBus IS
+ HART/4-20
IS
- HART/4-20
Optional SIL alarm Optional
alarm
2a
2b
3
4
5
S
+
Alarm Alarm +
ATEX/IECEx:
Zone 0
Division 1 or Zone 0
E x depa IIC Ga]
Gb T4
© I I 2(1)G E x depa
IIC]
T4
DIV. 1 G P C & D
depa IIC]
POWER
SUPPLY
(24/48 VDC,
4 8 , 65 and
50/60HZ)
PE
ENTITY P A R A M E T E R S :
lo 95.3
Group IEC:
VAC, N / L / +
Po
uF
2015-07-07 Electronic Master - Printed Copies Uncontrolled - Emerson Proprietary
WEEK
1525
HAZARDOUS AREA
Al
L // +
K1 A
WEEK
SME-8259
HART/4-20mA A C T I V E
E N T I T Y IS
Note 8. see sheet 1
9
K1 A
K1 COM
K2 A
K2 COM
Relay output
(Option)
Primary
Communication Bus
Secondary
Communication Bus
(Option)
Lo<15mH
Zone 1
Division 1
P BUS B
Zone 1
Tank B u s
FISCO POWER SUPPLY
Note 1, see sheet 1
9
S PWRS PWR
S BUS A
FM Approved Product
Shielded cable
No revision to this drawing
without prior Factory Mutual
Approval.
Optionally shielded cable
BY
EE-VN
APPROVED BY
CT)
Installation Notes (cont.):
The IS
EAp
WEEK
0844
PRODUCT CODE
2410
DOC. TYPE
ROSEMOUNT 2410
(HART/4-20mA ACTIVE
ALL DIMENSIONS ARE IN MILLIMETRES,
TOLERANCES, UNLESS OTHERWISE
STATED:
ENTITY IS
cable and the FB cable shall be treated as separate intrinsically safe circuits.
1 ST ANGLE
CM
CT)
S Y S T E M CONTROL DWG.
OPTION)
9240040-901
5
The
of
document Is and will remain ours.
The document must not be used without our authorization or brought
to the knowledge of a third party. Contravention will be prosecuted.
Rosemount
Tank RadarAB,
Sweden
ISSUE
1
ORIGINAL SIZE
NON-HAZARDOUS
AREA
Signal
X1
CH. ORDER No
SME-6096
WEEK
ISSUE
CH. ORDER No
2
SME-6989
WEEK
1113
ISSUE
3
CH. ORDER No
WEEK
NON-HAZARDOUS OR ZONE 1 / DIVISION 1 HAZARDOUS AREA
CH. ORDER No
Signal
Data
X2
Terminal
single terminals)
FB
1a
TankBus +
N / -
1
Power. Neutral / DC -
L/
2
Power. Line / DC +
rD -
K1 A
3
Relay 1 output (optional)
FB -
2a
TankBus -
K1 COM
4
Relay 1 common
FB-
2b
TankBus -
K2A
5
Relay 2 output (optional)
3
IS
K2 COM
S
Relay 2 common
TankBus
-
4
+ HART/4-20
- HART/4-20
B
7a
Primary comm. Bus
Alarm -
5
Optional SIL
P BUS B
7b
Primary comm. Bus
Alarm +
6
Optional
P BUS A
8a
Primary comm. Bus
P BUS A
8b
Primary
P
WEEK
HAZARDOUS AREA
Data
Terminal
ISSUE
SME-8259
alarm +
Bus
Not used
10
ALARM B
11
ARM A
12
used
SIL relay common
relay output NO
US/Canada:
Zone 0
Division 1
Zone 0
E x depa
Ga]
Gb T4
© I I 2(1)G E x depa IIC]
CL
POWER
SUPPLY
(24/48 VDC,
ENTITY P A R A M E T E R S :
- 23.1
lo =
mA; Po
PE
4 8 , 6 5 and
50/60HZ)
VAC,
T4
DIV. 1 G P C & D
550
/
L/ +
D, HA:
2015-07-07 Electronic Master - Printed Copies Uncontrolled - Emerson Proprietary
ACTIVE
K1 A
K1 COM
Relay output
(Option)
Note 8, see sheet 1
Note 10
K2 COM
Primary
Communication Bus
SIL Alarm Relay
Division 1 or Zone 1
P BUS B
P BUS A
SIL Alarm Input
Tank B u s
HSCO POWER SUPPLY
see
1
ALARM B
ALARM A
Note 10
FM A p p r o v e d P r o d u c t
Shielded cable
No revision to this drawing
Optionally shielded cable
without prior Factory Mutual
Approval.
BY
EE-VN
APPROVED BY
Oi EAp
Installation Notes
The IS
cable and the FB/Alarm cable shall be treated as separate intrinsically safe circuits.
•
o
o
o
CM
Oi
WEEK
0844
1029
PRODUCT CODE
2410
TYPE
S Y S T E M CONTROL DWG.
ROSEMOUNT 2410
(SIL OPTION AND HART/4-20mA ACTIVE
ALL DIMENSIONS ARE IN MILLIMETRES.
TOLERANCES,
OTHERWISE
STATED:
ENTITY IS
1 ST ANGLE
OPTION)
9240040-901
6 /8
The
of
document Is and
remain ours.
The document must not be used without our authorization or brought
to the knowledge of a third party. Contravention will be prosecuted.
Rosemount
Tank RadarAB,
Sweden
ORIGINAL SIZE
CH. ORDER No
1
NON-HAZARDOUS
AREA
Signal
Power, Neutral / DC -
L/ +
2
Power. Line /
K1 A
3
Relay 1 output (optional)
K1 COM
4
Relay 1 common
K2 A
5
Relay 2 output (optional)
K2 COM
6
Relay 2 common
P BUS B
Ta
comm. Bus
Tb
Primary comm. Bus
8a
Primary comm. Bus
8b
Primary comm. Bus
9
Secondary Power (optional)
10
Secondary Power 4
(optional)
11
Secondary comm. Bus
(optional)
12
Secondary comm. Bus
(optional)
2015-07-07 Electronic Master - Printed Copies Uncontrolled - Emerson Proprietary
POWER
SUPPLY
(24/48 VDC,
4 8 , 6 5 and
50/60Hz)
CH. ORDER No
WEEK
2
SME-6989
1113
ISSUE
3
CH. ORDER No
WEEK
SME-8259
Primary
Communication Bus
Secondary
Communication Bus
(Option)
WEEKJ
X2
Data
Terminal
1a
TankBus +
FB 4
1b
TankBus +
FB-
2a
TankBus -
FB-
2b
TankBus -
4
Alarm
US/Canada:
3
IS
4 HART/4-20 mA
4
IS
- HART/4-20
5
Optional SIL alarm -
6
Optional
alarm
Zonel
AEx/Ex depb
VAC, N /
Relay output
(Option)
C H . O R D E R NO
HAZARDOUS AREA
PE
L/ +
K1
K1
K2
K2
ISSUE
1525
single terminals)
1
4
ISSUE
Signal
N/-
S
WEEK
NON-HAZARDOUS OR ZONE 1 / DIVISION 1 HAZARDOUS AREA
X1
Data
Terminal
S PWR -
SME-6096
A
COM
A
COM
ENTITY P A R A M E T E R S :
30.0
300 mA; Ci = 0 uF; Li
IS
-
IS
+
PASSIVE
ENTITY
Note 8, see sheet 1
see sheet 5
Zonel
Division 1
P BUS B
0 mH
Zone 1
Tank Bus
FISCO POWER SUPPLY
1, see
9, see sheet 5
S
S BUS B
S BUS A
FM Approved Product
Associated
Apparatus
(Note 2, 5, 6 a n d 8.
S e e sheet 1)
No revision to this drawing
without prior Factory Mutual
Approval.
S Y S T E M CONTROL DWG.
ROSEMOUNT 2410
(HART/4-20mA PASSIVE
ENTITY IS
OPTION)
9240040-901
7 /8
The
of
document is and will remain ours.
The document must not be used without our authorization or brought
to the knowledge of a third party. Contravention will be prosecuted.
Rosemount
Tank RadarAB,
Sweden
ORIGINAL SIZE A3
NON-HAZARDOUS
AREA
Signal
X1
Terminal
1
Hi2
3
K1 A
K1 COM
4
K2A
5
K2 COM
6
7a
P BUS B
7b
8a
8b
9
10
ALARM B
11
ALARM A
12
ISSUE
CH. ORDER
WEEK
1
SME-6096
1029
ISSUE
2
CH. ORDER No
SME-6989
WEEK
1113
ISSUE
3
CH. ORDER No
NON-HAZARDOUS OR ZONE 1 / DIVISION 1 HAZARDOUS AREA
Data
single terminals)
Power,
Power,
+
Relay 1 output (optional)
Relay 1 common
Relay 2 output (optional)
Relay 2 common
Primary comm. Bus
Primary comm. Bus
Primary comm. Bus
Primary comm. Bus
Not used
Not used
SIL relay common
relay output NO
WEEK
ISSUE
WEEK
HAZARDOUS AREA
X2
Terminal
1a
1b
2a
2b
3
4
FB +
FB +
FBFB+
Alarm Alarm +
TankBus
TankBus +
TankBus TankBus IS
+ HART/4-20
VO - HART/4-20
Optional SIL alarm Optional SIL alarm +
5
6
US/Canada:
Zone 1
E x depb
Gb]
©II
POWER
SUPPLY
2015-07-07 Electronic Master - Printed Copies Uncontrolled - Emerson Proprietary
(24/48 VDC,
4 8 , 65 and
50/60HZ)
PE
Relay output
(Option)
Primary
Communication Bus
P BUS B
P BUS A
SIL Alarm Relay
Associated
Apparatus
(Note 2, 5, 6 and 8.
See sheet 1)
Gb T4
E x depb
T4
depb IIC]
ENTITY PARAMETERS:
VAC, N / / +
K1 A
K1 COM
K2 A
K2 COM
CH. ORDER No
SME-8259
300 mA;
Li
IS
-
HART/4-20mA
IS
+
ENTITY
Note 8, see sheet 1
Note 10, see sheet 5
ATEX/IECEx:
Zone 1
Division 1
Zone 1]
SIL Alarm Input
Tank B u s
FISCO POWER SUPPLY
see
1
Note
see sheet
ALARM B
ALARM A
FM Approved Product
No revision to this drawing
without prior Factory Mutual
Approval.
S Y S T E M CONTROL DWG.
ROSEMOUNT 2410
(SIL OPTION AND
ENTITY IS
OPTION)
PASSIVE
9240040-901
8
The
of this document is and will remain ours.
The document must not be used without our authorization or brought
to the knowledge of a third party. Contravention will be prosecuted.
Rosemount
Tank Radar AB,
Sweden