QoS Command Reference, Cisco IOS XE 3E (Cisco WLC 5700 Series)
First Published: June 16, 2014
Last Modified: 0,
Americas Headquarters
Cisco Systems, Inc.
170 West Tasman Drive
San Jose, CA 95134-1706
USA
http://www.cisco.com
Tel: 408 526-4000
800 553-NETS (6387)
Fax: 408 527-0883
Text Part Number: OL-32321-01
THE SPECIFICATIONS AND INFORMATION REGARDING THE PRODUCTS IN THIS MANUAL ARE SUBJECT TO CHANGE WITHOUT NOTICE. ALL STATEMENTS,
INFORMATION, AND RECOMMENDATIONS IN THIS MANUAL ARE BELIEVED TO BE ACCURATE BUT ARE PRESENTED WITHOUT WARRANTY OF ANY KIND,
EXPRESS OR IMPLIED. USERS MUST TAKE FULL RESPONSIBILITY FOR THEIR APPLICATION OF ANY PRODUCTS.
THE SOFTWARE LICENSE AND LIMITED WARRANTY FOR THE ACCOMPANYING PRODUCT ARE SET FORTH IN THE INFORMATION PACKET THAT SHIPPED WITH
THE PRODUCT AND ARE INCORPORATED HEREIN BY THIS REFERENCE. IF YOU ARE UNABLE TO LOCATE THE SOFTWARE LICENSE OR LIMITED WARRANTY,
CONTACT YOUR CISCO REPRESENTATIVE FOR A COPY.
The Cisco implementation of TCP header compression is an adaptation of a program developed by the University of California, Berkeley (UCB) as part of UCB's public domain version
of the UNIX operating system. All rights reserved. Copyright © 1981, Regents of the University of California.
NOTWITHSTANDING ANY OTHER WARRANTY HEREIN, ALL DOCUMENT FILES AND SOFTWARE OF THESE SUPPLIERS ARE PROVIDED “AS IS" WITH ALL FAULTS.
CISCO AND THE ABOVE-NAMED SUPPLIERS DISCLAIM ALL WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING, WITHOUT LIMITATION, THOSE OF
MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT OR ARISING FROM A COURSE OF DEALING, USAGE, OR TRADE PRACTICE.
IN NO EVENT SHALL CISCO OR ITS SUPPLIERS BE LIABLE FOR ANY INDIRECT, SPECIAL, CONSEQUENTIAL, OR INCIDENTAL DAMAGES, INCLUDING, WITHOUT
LIMITATION, LOST PROFITS OR LOSS OR DAMAGE TO DATA ARISING OUT OF THE USE OR INABILITY TO USE THIS MANUAL, EVEN IF CISCO OR ITS SUPPLIERS
HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
Any Internet Protocol (IP) addresses and phone numbers used in this document are not intended to be actual addresses and phone numbers. Any examples, command display output, network
topology diagrams, and other figures included in the document are shown for illustrative purposes only. Any use of actual IP addresses or phone numbers in illustrative content is unintentional
and coincidental.
Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its affiliates in the U.S. and other countries. To view a list of Cisco trademarks, go to this URL: http://
www.cisco.com/go/trademarks. Third-party trademarks mentioned are the property of their respective owners. The use of the word partner does not imply a partnership
relationship between Cisco and any other company. (1110R)
© 2014
Cisco Systems, Inc. All rights reserved.
CONTENTS
Preface
Preface v
Document Conventions v
Related Documentation vii
Obtaining Documentation and Submitting a Service Request vii
CHAPTER 1
Using the Command-Line Interface 1
Information About Using the Command-Line Interface 1
Command Modes 1
Understanding Abbreviated Commands 3
No and Default Forms of Commands 4
CLI Error Messages 4
Configuration Logging 4
Using the Help System 5
How to Use the CLI to Configure Features 6
Configuring the Command History 6
Changing the Command History Buffer Size 6
Recalling Commands 7
Disabling the Command History Feature 7
Enabling and Disabling Editing Features 8
Editing Commands Through Keystrokes 9
Editing Command Lines That Wrap 10
Searching and Filtering Output of show and more Commands 11
Accessing the CLI Through a Console Connection or Through Telnet 12
CHAPTER 2
QoS Commands 13
auto qos 15
class 16
QoS Command Reference, Cisco IOS XE 3E (Cisco WLC 5700 Series)
OL-32321-01
iii
Contents
class-map 19
match (class-map configuration) 21
match non-client-nrt 24
match wlan user-priority 25
policy-map 26
priority 29
queue-buffers ratio 31
queue-limit 33
qos wireless-default untrust 35
service-policy (Wired) 37
service-policy (WLAN) 39
set 41
show ap name service-policy 48
show ap name dot11 49
show class-map 52
show wireless client calls 53
show wireless client dot11 54
show wireless client mac-address (Call Control) 55
show wireless client mac-address (TCLAS) 56
show wireless client mac-address service-policy 57
show wireless client voice diagnostics 59
show policy-map 60
show wlan 65
show wlan qos service-policies 68
trust device 69
wireless qos statistics 71
QoS Command Reference, Cisco IOS XE 3E (Cisco WLC 5700 Series)
iv
OL-32321-01
Preface
• Document Conventions, page v
• Related Documentation, page vii
• Obtaining Documentation and Submitting a Service Request, page vii
Document Conventions
This document uses the following conventions:
Convention
Description
^ or Ctrl
Both the ^ symbol and Ctrl represent the Control (Ctrl) key on a keyboard. For
example, the key combination ^D or Ctrl-D means that you hold down the Control
key while you press the D key. (Keys are indicated in capital letters but are not
case sensitive.)
bold font
Commands and keywords and user-entered text appear in bold font.
Italic font
Document titles, new or emphasized terms, and arguments for which you supply
values are in italic font.
Courier
font
Bold Courier
Terminal sessions and information the system displays appear in courier font.
font
Bold Courier
font indicates text that the user must enter.
[x]
Elements in square brackets are optional.
...
An ellipsis (three consecutive nonbolded periods without spaces) after a syntax
element indicates that the element can be repeated.
|
A vertical line, called a pipe, indicates a choice within a set of keywords or
arguments.
[x | y]
Optional alternative keywords are grouped in brackets and separated by vertical
bars.
QoS Command Reference, Cisco IOS XE 3E (Cisco WLC 5700 Series)
OL-32321-01
v
Preface
Document Conventions
Convention
Description
{x | y}
Required alternative keywords are grouped in braces and separated by vertical
bars.
[x {y | z}]
Nested set of square brackets or braces indicate optional or required choices
within optional or required elements. Braces and a vertical bar within square
brackets indicate a required choice within an optional element.
string
A nonquoted set of characters. Do not use quotation marks around the string or
the string will include the quotation marks.
<>
Nonprinting characters such as passwords are in angle brackets.
[]
Default responses to system prompts are in square brackets.
!, #
An exclamation point (!) or a pound sign (#) at the beginning of a line of code
indicates a comment line.
Reader Alert Conventions
This document may use the following conventions for reader alerts:
Note
Tip
Caution
Timesaver
Warning
Means reader take note. Notes contain helpful suggestions or references to material not covered in the
manual.
Means the following information will help you solve a problem.
Means reader be careful. In this situation, you might do something that could result in equipment damage
or loss of data.
Means the described action saves time. You can save time by performing the action described in the
paragraph.
IMPORTANT SAFETY INSTRUCTIONS
This warning symbol means danger. You are in a situation that could cause bodily injury. Before you
work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar with
standard practices for preventing accidents. Use the statement number provided at the end of each warning
to locate its translation in the translated safety warnings that accompanied this device. Statement 1071
SAVE THESE INSTRUCTIONS
QoS Command Reference, Cisco IOS XE 3E (Cisco WLC 5700 Series)
vi
OL-32321-01
Preface
Related Documentation
Related Documentation
Note
Before installing or upgrading the controller, refer to the controller release notes.
• Cisco Validated Designs documents, located at:
http://www.cisco.com/go/designzone
• Error Message Decoder, located at:
https://www.cisco.com/cgi-bin/Support/Errordecoder/index.cgi
Obtaining Documentation and Submitting a Service Request
For information on obtaining documentation, submitting a service request, and gathering additional information,
see the monthly What's New in Cisco Product Documentation, which also lists all new and revised Cisco
technical documentation, at:
http://www.cisco.com/c/en/us/td/docs/general/whatsnew/whatsnew.html
Subscribe to the What's New in Cisco Product Documentation as a Really Simple Syndication (RSS) feed
and set content to be delivered directly to your desktop using a reader application. The RSS feeds are a free
service and Cisco currently supports RSS version 2.0.
QoS Command Reference, Cisco IOS XE 3E (Cisco WLC 5700 Series)
OL-32321-01
vii
Preface
Obtaining Documentation and Submitting a Service Request
QoS Command Reference, Cisco IOS XE 3E (Cisco WLC 5700 Series)
viii
OL-32321-01
Using the Command-Line Interface
• Information About Using the Command-Line Interface, page 1
• How to Use the CLI to Configure Features, page 6
Information About Using the Command-Line Interface
Command Modes
The Cisco IOS user interface is divided into many different modes. The commands available to you depend
on which mode you are currently in. Enter a question mark (?) at the system prompt to obtain a list of commands
available for each command mode.
You can start a CLI session through a console connection, through Telnet, an SSH, or by using the browser.
When you start a session, you begin in user mode, often called user EXEC mode. Only a limited subset of
the commands are available in user EXEC mode. For example, most of the user EXEC commands are one-time
commands, such as show commands, which show the current configuration status, and clear commands,
which clear counters or interfaces. The user EXEC commands are not saved when the controller reboots.
To have access to all commands, you must enter privileged EXEC mode. Normally, you must enter a password
to enter privileged EXEC mode. From this mode, you can enter any privileged EXEC command or enter
global configuration mode.
Using the configuration modes (global, interface, and line), you can make changes to the running configuration.
If you save the configuration, these commands are stored and used when the controller reboots. To access the
various configuration modes, you must start at global configuration mode. From global configuration mode,
you can enter interface configuration mode and line configuration mode .
This table describes the main command modes, how to access each one, the prompt you see in that mode, and
how to exit the mode.
QoS Command Reference, Cisco IOS XE 3E (Cisco WLC 5700 Series)
OL-32321-01
1
Using the Command-Line Interface
Command Modes
Table 1: Command Mode Summary
Mode
Access Method
User EXEC
Begin a session
using Telnet, SSH,
or console.
Prompt
Controller>
Exit Method
About This Mode
Enter logout or Use this mode to
quit.
• Change
terminal
settings.
• Perform basic
tests.
• Display system
information.
Privileged EXEC
While in user
EXEC mode, enter
the enable
command.
Controller#
Enter disable
to exit.
Use this mode to
verify commands
that you have
entered. Use a
password to protect
access to this mode.
Use this mode to
execute privilege
EXEC commands
for access points.
These commands are
not part of the
running config of the
controller, they are
sent to the IOS
config of the access
point.
Global
configuration
VLAN
configuration
While in privileged
EXEC mode, enter
the configure
command.
While in global
configuration
mode, enter the
vlan vlan-id
command.
Controller(config)#
To exit to
privileged
EXEC mode,
enter exit or
end, or press
Ctrl-Z.
Use this mode to
configure parameters
that apply to the
entire controller.
Use this mode to
configure access
point commands that
are part of the
running config of the
controller.
Controller(config-vlan)#
QoS Command Reference, Cisco IOS XE 3E (Cisco WLC 5700 Series)
2
OL-32321-01
Using the Command-Line Interface
Understanding Abbreviated Commands
Mode
Access Method
Prompt
Exit Method
About This Mode
To exit to
global
configuration
mode, enter the
exit command.
Use this mode to
configure VLAN
parameters. When
VTP mode is
transparent, you can
create
To return to
extended-range
privileged
VLANs (VLAN IDs
EXEC mode,
greater than 1005)
press Ctrl-Z or
and save
enter end.
configurations in the
controller startup
configuration file.
Interface
configuration
While in global
configuration
mode, enter the
interface command
(with a specific
interface).
Line configuration While in global
configuration
mode, specify a line
with the line vty or
line console
command.
Controller(config-if)#
To exit to
global
configuration
mode, enter
exit.
Use this mode to
configure parameters
for the Ethernet
ports.
To return to
privileged
EXEC mode,
press Ctrl-Z or
enter end.
Controller(config-line)#
To exit to
global
configuration
mode, enter
exit.
Use this mode to
configure parameters
for the terminal line.
To return to
privileged
EXEC mode,
press Ctrl-Z or
enter end.
Understanding Abbreviated Commands
You need to enter only enough characters for the controller to recognize the command as unique.
This example shows how to enter the show configuration privileged EXEC command in an abbreviated form:
Controller# show conf
QoS Command Reference, Cisco IOS XE 3E (Cisco WLC 5700 Series)
OL-32321-01
3
Using the Command-Line Interface
No and Default Forms of Commands
No and Default Forms of Commands
Almost every configuration command also has a no form. In general, use the no form to disable a feature or
function or reverse the action of a command. For example, the no shutdown interface configuration command
reverses the shutdown of an interface. Use the command without the keyword no to reenable a disabled feature
or to enable a feature that is disabled by default.
Configuration commands can also have a default form. The default form of a command returns the command
setting to its default. Most commands are disabled by default, so the default form is the same as the no form.
However, some commands are enabled by default and have variables set to certain default values. In these
cases, the default command enables the command and sets variables to their default values.
CLI Error Messages
This table lists some error messages that you might encounter while using the CLI to configure your controller.
Table 2: Common CLI Error Messages
Error Message
Meaning
How to Get Help
% Ambiguous command: "show
con"
You did not enter enough
characters for your controller to
recognize the command.
Reenter the command followed by
a question mark (?) without any
space between the command and
the question mark.
The possible keywords that you can
enter with the command appear.
% Incomplete command.
You did not enter all of the
Reenter the command followed by
keywords or values required by this a question mark (?) with a space
command.
between the command and the
question mark.
The possible keywords that you can
enter with the command appear.
% Invalid input detected at
‘^’ marker.
You entered the command
Enter a question mark (?) to display
incorrectly. The caret (^) marks the all of the commands that are
point of the error.
available in this command mode.
The possible keywords that you can
enter with the command appear.
Configuration Logging
You can log and view changes to the controller configuration. You can use the Configuration Change Logging
and Notification feature to track changes on a per-session and per-user basis. The logger tracks each
configuration command that is applied, the user who entered the command, the time that the command was
entered, and the parser return code for the command. This feature includes a mechanism for asynchronous
QoS Command Reference, Cisco IOS XE 3E (Cisco WLC 5700 Series)
4
OL-32321-01
Using the Command-Line Interface
Using the Help System
notification to registered applications whenever the configuration changes. You can choose to have the
notifications sent to the syslog.
Only CLI or HTTP changes are logged.
Note
Using the Help System
You can enter a question mark (?) at the system prompt to display a list of commands available for each
command mode. You can also obtain a list of associated keywords and arguments for any command.
SUMMARY STEPS
1. help
2. abbreviated-command-entry ?
3. abbreviated-command-entry <Tab>
4. ?
5. command ?
6. command keyword ?
DETAILED STEPS
Step 1
Command or Action
Purpose
help
Obtains a brief description of the help system in any
command mode.
Example:
Controller# help
Step 2
abbreviated-command-entry ?
Obtains a list of commands that begin with a particular
character string.
Example:
Controller# di?
dir disable disconnect
Step 3
abbreviated-command-entry <Tab>
Completes a partial command name.
Example:
Controller# sh conf<tab>
Controller# show configuration
Step 4
?
Lists all commands available for a particular command
mode.
Example:
Controller> ?
QoS Command Reference, Cisco IOS XE 3E (Cisco WLC 5700 Series)
OL-32321-01
5
Using the Command-Line Interface
How to Use the CLI to Configure Features
Step 5
Command or Action
Purpose
command ?
Lists the associated keywords for a command.
Example:
Controller> show ?
Step 6
command keyword ?
Lists the associated arguments for a keyword.
Example:
Controller(config)# cdp holdtime ?
<10-255> Length of time (in sec) that receiver
must keep this packet
How to Use the CLI to Configure Features
Configuring the Command History
The software provides a history or record of commands that you have entered. The command history feature
is particularly useful for recalling long or complex commands or entries, including access lists. You can
customize this feature to suit your needs.
Changing the Command History Buffer Size
By default, the controller records ten command lines in its history buffer. You can alter this number for a
current terminal session or for all sessions on a particular line. This procedure is optional.
SUMMARY STEPS
1. terminal history [size number-of-lines]
DETAILED STEPS
Step 1
Command or Action
Purpose
terminal history [size number-of-lines]
Changes the number of command lines that the controller records
during the current terminal session in privileged EXEC mode. You
can configure the size from 0 to 256.
Example:
Controller# terminal history size 200
QoS Command Reference, Cisco IOS XE 3E (Cisco WLC 5700 Series)
6
OL-32321-01
Using the Command-Line Interface
Configuring the Command History
Recalling Commands
To recall commands from the history buffer, perform one of the actions listed in this table. These actions are
optional.
Note
The arrow keys function only on ANSI-compatible terminals such as VT100s.
SUMMARY STEPS
1. Ctrl-P or use the up arrow key
2. Ctrl-N or use the down arrow key
3. show history
DETAILED STEPS
Command or Action
Purpose
Step 1
Ctrl-P or use the up arrow key
Recalls commands in the history buffer, beginning with the most recent command.
Repeat the key sequence to recall successively older commands.
Step 2
Ctrl-N or use the down arrow key Returns to more recent commands in the history buffer after recalling commands
with Ctrl-P or the up arrow key. Repeat the key sequence to recall successively
more recent commands.
Step 3
show history
Example:
Controller# show history
Lists the last several commands that you just entered in privileged EXEC mode.
The number of commands that appear is controlled by the setting of the terminal
history global configuration command and the history line configuration
command.
Disabling the Command History Feature
The command history feature is automatically enabled. You can disable it for the current terminal session or
for the command line. This procedure is optional.
SUMMARY STEPS
1. terminal no history
QoS Command Reference, Cisco IOS XE 3E (Cisco WLC 5700 Series)
OL-32321-01
7
Using the Command-Line Interface
Enabling and Disabling Editing Features
DETAILED STEPS
Step 1
Command or Action
Purpose
terminal no history
Disables the feature during the current terminal session in
privileged EXEC mode.
Example:
Controller# terminal no history
Enabling and Disabling Editing Features
Although enhanced editing mode is automatically enabled, you can disable it and reenable it.
SUMMARY STEPS
1. terminal editing
2. terminal no editing
DETAILED STEPS
Step 1
Command or Action
Purpose
terminal editing
Reenables the enhanced editing mode for the current terminal
session in privileged EXEC mode.
Example:
Controller# terminal editing
Step 2
terminal no editing
Disables the enhanced editing mode for the current terminal
session in privileged EXEC mode.
Example:
Controller# terminal no editing
QoS Command Reference, Cisco IOS XE 3E (Cisco WLC 5700 Series)
8
OL-32321-01
Using the Command-Line Interface
Enabling and Disabling Editing Features
Editing Commands Through Keystrokes
The keystrokes help you to edit the command lines. These keystrokes are optional.
Note
The arrow keys function only on ANSI-compatible terminals such as VT100s.
Table 3: Editing Commands
Editing Commands
Description
Ctrl-B or use the left arrow key
Moves the cursor back one character.
Ctrl-F or use the right arrow key
Moves the cursor forward one character.
Ctrl-A
Moves the cursor to the beginning of the command
line.
Ctrl-E
Moves the cursor to the end of the command line.
Esc B
Moves the cursor back one word.
Esc F
Moves the cursor forward one word.
Ctrl-T
Transposes the character to the left of the cursor with
the character located at the cursor.
Delete or Backspace key
Erases the character to the left of the cursor.
Ctrl-D
Deletes the character at the cursor.
Ctrl-K
Deletes all characters from the cursor to the end of
the command line.
Ctrl-U or Ctrl-X
Deletes all characters from the cursor to the beginning
of the command line.
Ctrl-W
Deletes the word to the left of the cursor.
Esc D
Deletes from the cursor to the end of the word.
Esc C
Capitalizes at the cursor.
Esc L
Changes the word at the cursor to lowercase.
Esc U
Capitalizes letters from the cursor to the end of the
word.
QoS Command Reference, Cisco IOS XE 3E (Cisco WLC 5700 Series)
OL-32321-01
9
Using the Command-Line Interface
Enabling and Disabling Editing Features
Ctrl-V or Esc Q
Designates a particular keystroke as an executable
command, perhaps as a shortcut.
Return key
Scrolls down a line or screen on displays that are
longer than the terminal screen can display.
Note
The More prompt is used for any output that
has more lines than can be displayed on the
terminal screen, including show command
output. You can use the Return and Space
bar keystrokes whenever you see the More
prompt.
Space bar
Scrolls down one screen.
Ctrl-L or Ctrl-R
Redisplays the current command line if the controller
suddenly sends a message to your screen.
Editing Command Lines That Wrap
You can use a wraparound feature for commands that extend beyond a single line on the screen. When the
cursor reaches the right margin, the command line shifts ten spaces to the left. You cannot see the first ten
characters of the line, but you can scroll back and check the syntax at the beginning of the command. The
keystroke actions are optional.
To scroll back to the beginning of the command entry, press Ctrl-B or the left arrow key repeatedly. You can
also press Ctrl-A to immediately move to the beginning of the line.
Note
The arrow keys function only on ANSI-compatible terminals such as VT100s.
The following example shows how to wrap a command line that extends beyond a single line on the screen.
SUMMARY STEPS
1. access-list
2. Ctrl-A
3. Return key
DETAILED STEPS
Step 1
Command or Action
Purpose
access-list
Displays the global configuration command entry that extends beyond
one line.
Example:
When the cursor first reaches the end of the line, the line is shifted ten
spaces to the left and redisplayed. The dollar sign ($) shows that the
Controller(config)# access-list 101 permit
QoS Command Reference, Cisco IOS XE 3E (Cisco WLC 5700 Series)
10
OL-32321-01
Using the Command-Line Interface
Searching and Filtering Output of show and more Commands
Step 2
Command or Action
Purpose
tcp 10.15.22.25 255.255.255.0 10.15.22.35
Controller(config)# $ 101 permit tcp
10.15.22.25 255.255.255.0 10.15.22.35
255.25
Controller(config)# $t tcp 10.15.22.25
255.255.255.0 131.108.1.20 255.255.255.0
eq
Controller(config)# $15.22.25 255.255.255.0
10.15.22.35 255.255.255.0 eq 45
line has been scrolled to the left. Each time the cursor reaches the end
of the line, the line is again shifted ten spaces to the left.
Ctrl-A
Checks the complete syntax.
Example:
The dollar sign ($) appears at the end of the line to show that the line
has been scrolled to the right.
Controller(config)# access-list 101 permit
tcp 10.15.22.25 255.255.255.0 10.15.2$
Step 3
Return key
Execute the commands.
The software assumes that you have a terminal screen that is 80
columns wide. If you have a different width, use the terminal width
privileged EXEC command to set the width of your terminal.
Use line wrapping with the command history feature to recall and
modify previous complex command entries.
Searching and Filtering Output of show and more Commands
You can search and filter the output for show and more commands. This is useful when you need to sort
through large amounts of output or if you want to exclude output that you do not need to see. Using these
commands is optional.
SUMMARY STEPS
1. {show | more} command | {begin | include | exclude} regular-expression
DETAILED STEPS
Step 1
Command or Action
Purpose
{show | more} command | {begin | include | exclude}
regular-expression
Searches and filters the output.
Example:
Controller# show interfaces | include protocol
Vlan1 is up, line protocol is up
Vlan10 is up, line protocol is down
GigabitEthernet1/0/1 is up, line protocol is down
GigabitEthernet1/0/2 is up, line protocol is up
Expressions are case sensitive. For example, if you enter
| exclude output, the lines that contain output are not
displayed, but the lines that contain output appear.
QoS Command Reference, Cisco IOS XE 3E (Cisco WLC 5700 Series)
OL-32321-01
11
Using the Command-Line Interface
Accessing the CLI Through a Console Connection or Through Telnet
Accessing the CLI Through a Console Connection or Through Telnet
Before you can access the CLI, you must connect a terminal or a PC to the controller console or connect a
PC to the Ethernet management port and then power on the controller, as described in the hardware installation
guide that shipped with your controller.
If your controller is already configured, you can access the CLI through a local console connection or through
a remote Telnet session, but your controller must first be configured for this type of access.
You can use one of these methods to establish a connection with the controller:
• Connect the controller console port to a management station or dial-up modem, or connect the Ethernet
management port to a PC. For information about connecting to the console or Ethernet management
port, see the controller hardware installation guide.
• Use any Telnet TCP/IP or encrypted Secure Shell (SSH) package from a remote management station.
The controller must have network connectivity with the Telnet or SSH client, and the controller must
have an enable secret password configured.
• The controller supports up to 16 simultaneous Telnet sessions. Changes made by one Telnet user
are reflected in all other Telnet sessions.
• The controller supports up to five simultaneous secure SSH sessions.
After you connect through the console port, through the Ethernet management port, through a Telnet
session or through an SSH session, the user EXEC prompt appears on the management station.
QoS Command Reference, Cisco IOS XE 3E (Cisco WLC 5700 Series)
12
OL-32321-01
QoS Commands
• auto qos, page 15
• class, page 16
• class-map, page 19
• match (class-map configuration), page 21
• match non-client-nrt, page 24
• match wlan user-priority, page 25
• policy-map, page 26
• priority, page 29
• queue-buffers ratio, page 31
• queue-limit, page 33
• qos wireless-default untrust, page 35
• service-policy (Wired), page 37
• service-policy (WLAN), page 39
• set, page 41
• show ap name service-policy, page 48
• show ap name dot11, page 49
• show class-map, page 52
• show wireless client calls, page 53
• show wireless client dot11, page 54
• show wireless client mac-address (Call Control), page 55
• show wireless client mac-address (TCLAS), page 56
• show wireless client mac-address service-policy, page 57
• show wireless client voice diagnostics, page 59
• show policy-map, page 60
QoS Command Reference, Cisco IOS XE 3E (Cisco WLC 5700 Series)
OL-32321-01
13
QoS Commands
• show wlan, page 65
• show wlan qos service-policies, page 68
• trust device, page 69
• wireless qos statistics, page 71
QoS Command Reference, Cisco IOS XE 3E (Cisco WLC 5700 Series)
14
OL-32321-01
QoS Commands
auto qos
auto qos
To enable Auto QoS Wireless Policy, use the auto qos command. To remove Auto QoS Wireless Policy, use
the no form of this command.
auto qos enterprise|guest|voice
Syntax Description
enterprise
Enables AutoQos Wireless Enterprise Policy.
guest
Enables AutoQos Wireless Guest Policy
voice
Enables AutoQos Wireless Voice Policy
Command Default
None
Command Modes
WLAN Configuration
Command History
Examples
Release
Modification
Cisco IOS XE 3.7.0 E
This command was introduced.
This example shows how to enable AutoQos Wireless Enterprise Policy.
Controller# configure terminal
Enter configuration commands, one per line.
Controller(config)#wlan wlan1
Controller(config-wlan)#auto qos enterprise
End with CNTL/Z.
QoS Command Reference, Cisco IOS XE 3E (Cisco WLC 5700 Series)
OL-32321-01
15
QoS Commands
class
class
To define a traffic classification match criteria for the specified class-map name, use the class command in
policy-map configuration mode. Use the no form of this command to delete an existing class map.
class {class-map-name | class-default}
no class {class-map-name | class-default}
Syntax Description
class-map-name
The class map name.
class-default
Refers to a system default class that matches unclassified packets.
Command Default
No policy map class-maps are defined.
Command Modes
Policy-map configuration
Command History
Usage Guidelines
Release
Modification
Cisco IOS XE 3.2SE
This command was introduced.
Before using the class command, you must use the policy-map global configuration command to identify the
policy map and enter policy-map configuration mode. After specifying a policy map, you can configure a
policy for new classes or modify a policy for any existing classes in that policy map. You attach the policy
map to a port by using the service-policy interface configuration command.
After entering the class command, you enter the policy-map class configuration mode. These configuration
commands are available:
• admit—Admits a request for Call Admission Control (CAC)
• bandwidth—Specifies the bandwidth allocated to the class.
• exit—Exits the policy-map class configuration mode and returns to policy-map configuration mode.
• no—Returns a command to its default setting.
• police—Defines a policer or aggregate policer for the classified traffic. The policer specifies the bandwidth
limitations and the action to take when the limits are exceeded. For more information about this command,
see Cisco IOS Quality of Service Solutions Command Reference available on Cisco.com.
• priority—Assigns scheduling priority to a class of traffic belonging to a policy map.
• queue-buffers—Configures the queue buffer for the class.
QoS Command Reference, Cisco IOS XE 3E (Cisco WLC 5700 Series)
16
OL-32321-01
QoS Commands
class
• queue-limit—Specifies the maximum number of packets the queue can hold for a class policy configured
in a policy map.
• service-policy—Configures a QoS service policy.
• set—Specifies a value to be assigned to the classified traffic. For more information, see set, on page
41
• shape—Specifies average or peak rate traffic shaping. For more information about this command, see
Cisco IOS Quality of Service Solutions Command Reference available on Cisco.com.
To return to policy-map configuration mode, use the exit command. To return to privileged EXEC mode, use
the end command.
The class command performs the same function as the class-map global configuration command. Use the
class command when a new classification, which is not shared with any other ports, is needed. Use the
class-map command when the map is shared among many ports.
You can configure a default class by using the class class-default policy-map configuration command.
Unclassified traffic (traffic that does not meet the match criteria specified in the traffic classes) is treated as
default traffic.
You can verify your settings by entering the show policy-map privileged EXEC command.
Examples
This example shows how to create a policy map called policy1. When attached to the ingress direction, it
matches all the incoming traffic defined in class1, sets the IP Differentiated Services Code Point (DSCP) to
10, and polices the traffic at an average rate of 1 Mb/s and bursts at 20 KB. Traffic exceeding the profile is
marked down to a DSCP value gotten from the policed-DSCP map and then sent.
Controller(config)# policy-map policy1
Controller(config-pmap)# class class1
Controller(config-pmap-c)# set dscp 10
Controller(config-pmap-c)# police 1000000 20000 exceed-action policed-dscp-transmit
Controller(config-pmap-c)# exit
This example shows how to configure a default traffic class to a policy map. It also shows how the default
traffic class is automatically placed at the end of policy-map pm3 even though class-default was configured
first:
Controller# configure terminal
Controller(config)# class-map cm-3
Controller(config-cmap)# match ip dscp 30
Controller(config-cmap)# exit
Controller(config)# class-map cm-4
Controller(config-cmap)# match ip dscp 40
Controller(config-cmap)# exit
Controller(config)# policy-map pm3
Controller(config-pmap)# class class-default
Controller(config-pmap-c)# set dscp 10
Controller(config-pmap-c)# exit
Controller(config-pmap)# class cm-3
Controller(config-pmap-c)# set dscp 4
Controller(config-pmap-c)# exit
Controller(config-pmap)# class cm-4
Controller(config-pmap-c)# set precedence 5
Controller(config-pmap-c)# exit
Controller(config-pmap)# exit
Controller# show policy-map pm3
QoS Command Reference, Cisco IOS XE 3E (Cisco WLC 5700 Series)
OL-32321-01
17
QoS Commands
class
Policy Map pm3
Class cm-3
set dscp 4
Class cm-4
set precedence 5
Class class-default
set dscp af11
Related Commands
Command
Description
class-map
Creates a class map to be used for matching packets to the class whose name
you specify and enters class-map configuration mode.
policy-map
Creates or modifies a policy map that can be attached to multiple physical ports
or SVIs and enters policy-map configuration mode.
show policy-map
Displays QoS policy maps.
set
Classifies IP traffic by setting a DSCP or an IP-precedence value in the packet.
QoS Command Reference, Cisco IOS XE 3E (Cisco WLC 5700 Series)
18
OL-32321-01
QoS Commands
class-map
class-map
To create a class map to be used for matching packets to the class whose name you specify and to enter
class-map configuration mode, use the class-map command in global configuration mode. Use the no form
of this command to delete an existing class map and to return to global or policy map configuration mode.
class-map [match-any| type] class-map-name
no class-map [match-any| type] class-map-name
Syntax Description
match-any
(Optional) Perform a logical-OR of the matching statements under this
class map. One or more criteria must be matched.
type
(Optional) Configures the CPL class map.
class-map-name
The class map name.
Command Default
No class maps are defined.
Command Modes
Global configuration
Policy map configuration
Command History
Usage Guidelines
Release
Modification
Cisco IOS XE 3.2SE
This command was introduced.
Cisco IOS XE 3.3SE
The type keyword was added.
Use this command to specify the name of the class for which you want to create or modify class-map match
criteria and to enter class-map configuration mode.
The class-map command and its subcommands are used to define packet classification, marking, and aggregate
policing as part of a globally named service policy applied on a per-port basis.
After you are in quality of service (QoS) class-map configuration mode, these configuration commands are
available:
• description—Describes the class map (up to 200 characters). The show class-map privileged EXEC
command displays the description and the name of the class map.
• exit—Exits from QoS class-map configuration mode.
• match—Configures classification criteria.
QoS Command Reference, Cisco IOS XE 3E (Cisco WLC 5700 Series)
OL-32321-01
19
QoS Commands
class-map
• no—Removes a match statement from a class map.
If you enter the match-any keyword, you can only use it to specify an extended named access control list
(ACL) with the match access-group class-map configuration command.
To define packet classification on a physical-port basis, only one match command per class map is supported.
The ACL can have multiple access control entries (ACEs).
Examples
This example shows how to configure the class map called class1 with one match criterion, which is an access
list called 103:
Controller(config)# access-list 103 permit ip any any dscp 10
Controller(config)# class-map class1
Controller(config-cmap)# match access-group 103
Controller(config-cmap)# exit
This example shows how to delete the class map class1:
Controller(config)# no class-map class1
You can verify your settings by entering the show class-map privileged EXEC command.
Related Commands
Command
Description
policy-map
Creates or modifies a policy map that can be attached to multiple physical
ports or SVIs and enters policy-map configuration mode.
show policy-map
Displays QoS policy maps.
QoS Command Reference, Cisco IOS XE 3E (Cisco WLC 5700 Series)
20
OL-32321-01
QoS Commands
match (class-map configuration)
match (class-map configuration)
To define the match criteria to classify traffic, use the match command in class-map configuration mode. Use
the no form of this command to remove the match criteria.
match {access-group{nameacl-name | acl-index}| class-map class-map-name| cos cos-value| dscp dscp-value|
[ ip ] dscp dscp-list | [ip] precedence ip-precedence-list| precedence precedence-value1...value4| qos-group
qos-group-value| vlan vlan-id}
no match {access-group{nameacl-name | acl-index}| class-map class-map-name| cos cos-value| dscp
dscp-value| [ ip ] dscp dscp-list | [ip] precedence ip-precedence-list| precedence precedence-value1...value4|
qos-group qos-group-value| vlan vlan-id}
Syntax Description
access-group
Specifies an access group.
name acl-name
Specifies the name of an IP standard or extended access
control list (ACL) or MAC ACL.
acl-index
Specifies the number of an IP standard or extended access
control list (ACL) or MAC ACL. For an IP standard ACL,
the ACL index range is 1 to 99 and 1300 to 1999. For an
IP extended ACL, the ACL index range is 100 to 199
and 2000 to 2699.
class-map class-map-name
Uses a traffic class as a classification policy and specifies
a traffic class name to use as the match criterion.
cos cos-value
Matches a packet on the basis of a Layer 2 class of service
(CoS)/Inter-Switch Link (ISL) marking. The cos-value is
from 0 to 7. You can specify up to four CoS values in one
match cos statement, separated by a space.
dscp dscp-value
Specifies the parameters for each DSCP value. You can
specify a value in the range 0 to 63 specifying the
differentiated services code point value.
ip dscp dscp-list
Specifies a list of up to eight IP Differentiated Services
Code Point (DSCP) values to match against incoming
packets. Separate each value with a space. The range is 0
to 63. You also can enter a mnemonic name for a
commonly used value.
ip precedence ip-precedence-list
Specifies a list of up to eight IP-precedence values to match
against incoming packets. Separate each value with a space.
The range is 0 to 7. You also can enter a mnemonic name
for a commonly used value.
QoS Command Reference, Cisco IOS XE 3E (Cisco WLC 5700 Series)
OL-32321-01
21
QoS Commands
match (class-map configuration)
precedence precedence-value1...value4
Assigns an IP precedence value to the classified traffic.
The range is 0 to 7. You also can enter a mnemonic name
for a commonly used value.
qos-group qos-group-value
Identifies a specific QoS group value as a match criterion.
The range is 0 to 31.
vlan vlan-id
Identifies a specific VLAN as a match criterion. The range
is 1 to 4095.
Command Default
No match criteria are defined.
Command Modes
Class-map configuration
Command History
Usage Guidelines
Release
Modification
Cisco IOS XE 3.2SE
This command was introduced.
Cisco IOS XE 3.3SE
The class-map class-map-name, cos cos-value, qos-group
qos-group-value, and vlan vlan-id keywords were added.
The match command is used to specify which fields in the incoming packets are examined to classify the
packets. Only the IP access group or the MAC access group matching to the Ether Type/Len are supported.
If you enter the class-map match-anyclass-map-name global configuration command, you can enter the
following match commands:
• match access-group name acl-name
Note
The ACL must be an extended named ACL.
• match ip dscp dscp-list
• match ip precedence ip-precedence-list
The match access-group acl-index command is not supported.
To define packet classification on a physical-port basis, only one match command per class map is supported.
In this situation, the match-any keyword is equivalent.
For the match ip dscp dscp-list or the match ip precedence ip-precedence-list command, you can enter a
mnemonic name for a commonly used value. For example, you can enter the match ip dscp af11 command,
which is the same as entering the match ip dscp 10 command. You can enter the match ip precedence critical
command, which is the same as entering the match ip precedence 5 command. For a list of supported
QoS Command Reference, Cisco IOS XE 3E (Cisco WLC 5700 Series)
22
OL-32321-01
QoS Commands
match (class-map configuration)
mnemonics, enter the match ip dscp ? or the match ip precedence ? command to see the command-line help
strings.
Use the input-interface interface-id-list keyword when you are configuring an interface-level class map in
a hierarchical policy map. For the interface-id-list, you can specify up to six entries.
Examples
This example shows how to create a class map called class2, which matches all the incoming traffic with
DSCP values of 10, 11, and 12:
Controller(config)# class-map class2
Controller(config-cmap)# match ip dscp 10 11 12
Controller(config-cmap)# exit
This example shows how to create a class map called class3, which matches all the incoming traffic with
IP-precedence values of 5, 6, and 7:
Controller(config)# class-map class3
Controller(config-cmap)# match ip precedence 5 6 7
Controller(config-cmap)# exit
This example shows how to delete the IP-precedence match criteria and to classify traffic using acl1:
Controller(config)# class-map class2
Controller(config-cmap)# match ip precedence 5 6 7
Controller(config-cmap)# no match ip precedence
Controller(config-cmap)# match access-group acl1
Controller(config-cmap)# exit
This example shows how to specify a list of physical ports to which an interface-level class map in a hierarchical
policy map applies:
Controller(config)# class-map match-any class4
Controller(config-cmap)# match cos 4
Controller(config-cmap)# exit
This example shows how to specify a range of physical ports to which an interface-level class map in a
hierarchical policy map applies:
Controller(config)# class-map match-any class4
Controller(config-cmap)# match cos 4
Controller(config-cmap)# exit
You can verify your settings by entering the show class-map privileged EXEC command.
QoS Command Reference, Cisco IOS XE 3E (Cisco WLC 5700 Series)
OL-32321-01
23
QoS Commands
match non-client-nrt
match non-client-nrt
To match non-client NRT (non-real-time), use the match non-client-nrt command in class-map configuration
mode. Use the no form of this command to return to the default setting.
match non-client-nrt
no match non-client-nrt
Syntax Description
This command has no arguments or keywords.
Command Default
None
Command Modes
Class-map
Command History
Release
Modification
Cisco IOS XE 3.2SE
This command was introduced.
Usage Guidelines
None
Examples
This example show how you can configure non-client NRT:
Controller(config)# class-map test_1000
Controller(config-cmap)# match non-client-nrt
QoS Command Reference, Cisco IOS XE 3E (Cisco WLC 5700 Series)
24
OL-32321-01
QoS Commands
match wlan user-priority
match wlan user-priority
To match 802.11 specific values, use the match wlan user-priority command in class-map configuration
mode. Use the no form of this command to return to the default setting.
match wlan user-priority wlan-value [wlan-value] [wlan-value] [wlan-value]
no match wlan user-priority wlan-value [wlan-value] [wlan-value] [wlan-value]
Syntax Description
wlan-value
The 802.11-specific values. Enter the user priority 802.11 TID user priority (0-7).
(Optional) Enter up to three user priority values separated by white-spaces.
Command Default
None
Command Modes
Class-map
Command History
Release
Modification
Cisco IOS XE 3.2SE
This command was introduced.
Usage Guidelines
None
Examples
This example show how you can configure user-priority values:
Controller(config)# class-map test_1000
Controller(config-cmap)# match wlan user-priority 7
QoS Command Reference, Cisco IOS XE 3E (Cisco WLC 5700 Series)
OL-32321-01
25
QoS Commands
policy-map
policy-map
To create or modify a policy map that can be attached to multiple physical ports or switch virtual interfaces
(SVIs) and to enter policy-map configuration mode, use the policy-map command in global configuration
mode. Use the no form of this command to delete an existing policy map and to return to global configuration
mode.
policy-map policy-map-name
no policy-map policy-map-name
Syntax Description
policy-map-name
Command Default
No policy maps are defined.
Command Modes
Global configuration
Command History
Usage Guidelines
Name of the policy map.
Release
Modification
Cisco IOS XE 3.2SE
This command was introduced.
After entering the policy-map command, you enter policy-map configuration mode, and these configuration
commands are available:
• class—Defines the classification match criteria for the specified class map.
• description—Describes the policy map (up to 200 characters).
• exit—Exits policy-map configuration mode and returns you to global configuration mode.
• no—Removes a previously defined policy map.
• sequence-interval—Enables sequence number capability.
To return to global configuration mode, use the exit command. To return to privileged EXEC mode, use the
end command.
Before configuring policies for classes whose match criteria are defined in a class map, use the policy-map
command to specify the name of the policy map to be created, added to, or modified. Entering the policy-map
command also enables the policy-map configuration mode in which you can configure or modify the class
policies for that policy map.
You can configure class policies in a policy map only if the classes have match criteria defined for them. To
configure the match criteria for a class, use the class-map global configuration and match class-map
configuration commands. You define packet classification on a physical-port basis.
QoS Command Reference, Cisco IOS XE 3E (Cisco WLC 5700 Series)
26
OL-32321-01
QoS Commands
policy-map
Only one policy map per ingress port is supported. You can apply the same policy map to multiple physical
ports.
You can apply a nonhierarchical policy maps to physical ports. A nonhierarchical policy map is the same as
the port-based policy maps in the controller.
A hierarchical policy map has two levels in the format of a parent-child policy. The parent policy cannot be
modified but the child policy (port-child policy) can be modified to suit the QoS configuration.
In VLAN-based QoS, a service policy is applied to an SVI interface. All physical interfaces belonging to a
VLAN policy map then need to be configured to refer to the VLAN-based policy maps instead of the port-based
policy map.
Note
Examples
Not all MQC QoS combinations are supported for wired and wireless ports. For information about these
restrictions, see chapters "Restrictions for QoS on Wired Targets" and "Restrictions for QoS on Wireless
Targets" in the QoS configuration guide.
This example shows how to create a policy map called policy1. When attached to the ingress port, it matches
all the incoming traffic defined in class1, sets the IP DSCP to 10, and polices the traffic at an average rate of
1 Mb/s and bursts at 20 KB. Traffic less than the profile is sent.
Controller(config)# policy-map policy1
Controller(config-pmap)# class class1
Controller(config-pmap-c)# set dscp 10
Controller(config-pmap-c)# police 1000000 20000 conform-action transmit
Controller(config-pmap-c)# exit
This example show you how to configure hierarchical polices:
Switch# configure terminal
Controller(config)# class-map c1
Controller(config-cmap)# exit
Controller(config)# class-map c2
Controller(config-cmap)# exit
Controller(config)# policy-map child
Controller(config-pmap)# class c1
Controller(config-pmap-c)# priority level 1
Controller(config-pmap-c)# police rate percent 20 conform-action transmit exceed action
drop
Controller(config-pmap-c-police)# exit
Controller(config-pmap-c)# exit
Controller(config-pmap)# class c2
Controller(config-pmap-c)# bandwidth 20000
Controller(config-pmap-c)# exit
Controller(config-pmap)# class class-default
Controller(config-pmap-c)# bandwidth 20000
Controller(config-pmap-c)# exit
Controller(config-pmap)# exit
Controller(config)# policy-map parent
Controller(config-pmap)# class class-default
Controller(config-pmap-c)# shape average 1000000
Controller(config-pmap-c)# service-policy child
Controllerconfig-pmap-c)# end
QoS Command Reference, Cisco IOS XE 3E (Cisco WLC 5700 Series)
OL-32321-01
27
QoS Commands
policy-map
This example shows how to delete a policy map:
Controller(config)# no policy-map policymap2
You can verify your settings by entering the show policy-map privileged EXEC command.
Related Commands
Command
Description
class
Defines a traffic classification match criteria for the specified class-map
name.
class-map
Creates a class map to be used for matching packets to the class whose
name you specify and enters class-map configuration mode.
service-policy (Wired)
Applies a policy map to a physical port or an SVI.
show policy-map
Displays QoS policy maps.
QoS Command Reference, Cisco IOS XE 3E (Cisco WLC 5700 Series)
28
OL-32321-01
QoS Commands
priority
priority
To assign priority to a class of traffic belonging to a policy map, use the priority command in policy-map
class configuration mode. To remove a previously specified priority for a class, use the no form of this
command.
priority [Kbps [burst -in-bytes] | level level-value [Kbps [burst -in-bytes] ] | percent percentage [Kb/s [burst
-in-bytes] ] ]
no priority [Kb/s [burst -in-bytes] | level level value [Kb/s [burst -in-bytes] ] | percent percentage [Kb/s
[burst -in-bytes] ] ]
Syntax Description
Kb/s
(Optional) Guaranteed allowed bandwidth, in kilobits per second
(kbps), for the priority traffic. The amount of guaranteed bandwidth
varies according to the interface and platform in use. Beyond the
guaranteed bandwidth, the priority traffic will be dropped in the event
of congestion to ensure that the nonpriority traffic is not starved. The
value must be between 1 and 2,000,000 kbps.
burst -in-bytes
(Optional) Burst size in bytes. The burst size configures the network
to accommodate temporary bursts of traffic. The default burst value,
which is computed as 200 milliseconds of traffic at the configured
bandwidth rate, is used when the burst argument is not specified.
The range of the burst is from 32 to 2000000 bytes.
level level-value
(Optional) Assigns priority level. Available values for level-value
are 1 and 2. Level 1 is a higher priority than Level 2. Level 1 reserves
bandwidth and goes first, so latency is very low. Reserve the
bandwidth even if you do not use it. Both levels 1 and 2 can reserve
bandwidth.
percent percentage
(Optional) Specifies the amount of guaranteed bandwidth to be
specified by the percent of available bandwidth.
Command Default
No priority is set.
Command Modes
Policy-map class configuration
Command History
Release
Modification
Cisco IOS XE 3.2SE
This command was introduced.
Cisco IOS XE 3.3SE
The Kbps, burst -in-bytes, and percent percentage keywords
were added.
QoS Command Reference, Cisco IOS XE 3E (Cisco WLC 5700 Series)
OL-32321-01
29
QoS Commands
priority
Usage Guidelines
Note
This command configures low latency queuing (LLQ), providing strict priority queuing (PQ) for class-based
weighted fair queuing (CBWFQ). Strict PQ allows delay-sensitive data such as voice to be dequeued and sent
before packets in other queues are dequeued.
You can configure a priority only with a level.
Only one strict priority or priority with levels is allowed in one policy-map. Multiple priorities with same
priority levels without kbps/percent are allowed in a policy-map only if all of them are configured with
police.
The priority command allows you to set up classes based on a variety of criteria (not just User Datagram Ports
[UDP] ports) and assign priority to them, and is available for use on serial interfaces and ATM permanent
virtual circuits (PVCs). A similar command, the ip rtp priority command, allows you to stipulate priority
flows based only on UDP port numbers and is not available for ATM PVCs.
When the device is not congested, the priority class traffic is allowed to exceed its allocated bandwidth. When
the device is congested, the priority class traffic above the allocated bandwidth is discarded.
The bandwidth and priority commands cannot be used in the same class, within the same policy map. However,
these commands can be used together in the same policy map.
Within a policy map, you can give one or more classes priority status. When multiple classes within a single
policy map are configured as priority classes, all traffic from these classes is queued to the same, single,
priority queue.
When the policy map containing class policy configurations is attached to the interface to stipulate the service
policy for that interface, available bandwidth is assessed. If a policy map cannot be attached to a particular
interface because of insufficient interface bandwidth, the policy is removed from all interfaces to which it
was successfully attached.
Examples
The following example shows how to configure the priority of the class in policy map policy1:
Controller(config)# class-map cm1
Controller(config-cmap)#match precedence 2
Controller(config-cmap)#exit
Controller(config)#class-map cm2
Controller(config-cmap)#match dscp 30
Controller(config-cmap)#exit
Controller(config)# policy-map policy1
Controller(config-pmap)# class cm1
Controller(config-pmap-c)# priority level 1
Controller(config-pmap-c)# police 1m
Controller(config-pmap-c-police)#exit
Controller(config-pmap-c)#exit
Controller(config-pmap)#exit
Controller(config)#policy-map policy1
Controller(config-pmap)#class cm2
Controller(config-pmap-c)#priority level 2
Controller(config-pmap-c)#police 1m
QoS Command Reference, Cisco IOS XE 3E (Cisco WLC 5700 Series)
30
OL-32321-01
QoS Commands
queue-buffers ratio
queue-buffers ratio
To configure the queue buffer for the class, use the queue-buffers ratio command in policy-map class
configuration mode. Use the no form of this command to remove the ratio limit.
queue-buffers ratio ratio limit
no queue-buffers ratio ratio limit
Syntax Description
ratio limit
(Optional) Configures the queue buffer for the class. Enter the queue buffers
ratio limit (0-100).
Command Default
No queue buffer for the class is defined.
Command Modes
Policy-map class configuration
Command History
Usage Guidelines
Release
Modification
Cisco IOS XE 3.2SE
This command was introduced.
Either the bandwidth, shape, or priority command must be used before using this command. For more
information about these commands, see Cisco IOS Quality of Service Solutions Command Reference available
on Cisco.com
The controller allows you to allocate buffers to queues. If buffers are not allocated, then they are divided
equally amongst all queues. You can use the queue-buffer ratio to divide it in a particular ratio. The buffers
are soft buffers because Dynamic Threshold and Scaling (DTS) is active on all queues by default.
Note
Examples
The queue-buffer ratio is supported on both wired and wireless ports, but the queue-buffer ratio cannot
be configured with a queue-limit.
The following example sets the queue buffers ratio to 10 percent:
Controller(config)# policy-map policy_queuebuf01
Controller(config-pmap)# class-map class_queuebuf01
Controller(config-cmap)# exit
Controller(config)# policy policy_queuebuf01
Controller(config-pmap)# class class_queuebuf01
Controller(config-pmap-c)# bandwidth percent 80
Controller(config-pmap-c)# queue-buffers ratio 10
QoS Command Reference, Cisco IOS XE 3E (Cisco WLC 5700 Series)
OL-32321-01
31
QoS Commands
queue-buffers ratio
Controller(config-pmap)# end
You can verify your settings by entering the show policy-map privileged EXEC command.
Related Commands
Command
Description
show policy-map
Displays QoS policy maps.
QoS Command Reference, Cisco IOS XE 3E (Cisco WLC 5700 Series)
32
OL-32321-01
QoS Commands
queue-limit
queue-limit
To specify or modify the maximum number of packets the queue can hold for a class policy configured in a
policy map, use the queue-limit policy-map class configuration command. To remove the queue packet limit
from a class, use the no form of this command.
queue-limit queue-limit-size [packets] {cos cos-value| dscp dscp-value} percent percentage-of-packets
no queue-limit queue-limit-size [packets] {cos cos-value| dscp dscp-value} percent percentage-of-packets
Syntax Description
queue-limit-size
The maximum size of the queue. The maximum varies
according to the optional unit of measure keyword
specified ( bytes, ms, us, or packets).
cos cos-value
Specifies parameters for each cos value. CoS values are
from 0 to 7.
dscp dscp-value
Specifies parameters for each DSCP value.
You can specify a value in the range 0 to 63 specifying
the differentiated services code point value for the type
of queue limit .
percent percentage-of-packets
Command Default
None
Command Modes
Policy-map class configuration
Command History
Usage Guidelines
Note
A percentage in the range 1 to 100 specifying the
maximum percentage of packets that the queue for this
class can accumulate.
Release
Modification
Cisco IOS XE 3.2SE
This command was introduced.
Although visible in the command line help-strings, the packets unit of measure is not supported; use the
percent unit of measure.
This command is supported only on wired ports in the egress direction.
QoS Command Reference, Cisco IOS XE 3E (Cisco WLC 5700 Series)
OL-32321-01
33
QoS Commands
queue-limit
Weighted fair queuing (WFQ) creates a queue for every class for which a class map is defined. Packets
satisfying the match criteria for a class accumulate in the queue reserved for the class until they are sent, which
occurs when the queue is serviced by the fair queuing process. When the maximum packet threshold you
defined for the class is reached, queuing of any further packets to the class queue causes tail drop.
You use queue limits to configure Weighted Tail Drop (WTD). WTD ensures the configuration of more than
one threshold per queue. Each class of service is dropped at a different threshold value to provide for QoS
differentiation.
You can configure the maximum queue thresholds for the different subclasses of traffic, that is, DSCP and
CoS and configure the maximum queue thresholds for each subclass.
Examples
The following example configures a policy map called port-queue to contain policy for a class called dscp-1.
The policy for this class is set so that the queue reserved for it has a maximum packet limit of 20 percent:
Controller(config)# policy-map policy11
Controller(config-pmap)# class dscp-1
Controller(config-pmap-c)# bandwidth percent 20
Controller(config-pmap-c)# queue-limit dscp 1 percent 20
QoS Command Reference, Cisco IOS XE 3E (Cisco WLC 5700 Series)
34
OL-32321-01
QoS Commands
qos wireless-default untrust
qos wireless-default untrust
To configure the default trust behavior to untrust wireless packets, use the qos wireless-default untrust
command. To configure the default trust behavior of wireless traffic to trust, use the no form of the command.
qos wireless-default-untrust
no qos wireless-default-untrust
Syntax Description
This command has no arguments or keywords.
Command Default
By default, the wireless traffic is untrusted.
To check the trust behavior on the controller, use the show running-config | sec qos or the show run | include
untrust command.
Command Modes
Command History
Configuration
Release
Modification
Cisco IOS XE 3.3SE
This command was introduced.
Usage Guidelines
Note
The default trust behavior of wireless traffic was untrusted in the Cisco IOS XE 3.2 SE release.
Note
If you upgrade from Cisco IOS XE 3.2 SE Release to a later release, the default behavior of the wireless
traffic is still untrusted. In this situation, you can use the no qos wireless-default untrust command to
enable trust behavior for wireless traffic. However, if you install Cisco IOS XE 3.3 SE or a later release
on the controller, the default QoS behavior for wireless traffic is trust. Starting with Cisco IOS XE 3.3 SE
Release and later, the packet markings are preserved in both egress and ingress directions for new
installations (not upgrades) for wireless traffic.
The Cisco IOS XE 3.2 Release supported different trust defaults for wired and wireless ports. The trust default
for wired ports was the same as for this software release. For wireless ports, the default system behavior was
non-trust, which meant that when the controller came up, all markings for the wireless ports were defaulted
to zero and no traffic received priority treatment. For compatibility with an existing wired controller, all traffic
went to the best-effort queue by default. The access point performed priority queuing by default. In the
downstream direction, the access point maintained voice, video, best-effort, and background queues for
queuing. The access selected the queuing strategy based on the 11e tag information. By default, the access
point treated all wireless packets as best effort.
QoS Command Reference, Cisco IOS XE 3E (Cisco WLC 5700 Series)
OL-32321-01
35
QoS Commands
qos wireless-default untrust
Examples
The following command changes the default behavior for trusting wireless traffic to untrust.
Controller(config)# qos wireless-default-untrust
QoS Command Reference, Cisco IOS XE 3E (Cisco WLC 5700 Series)
36
OL-32321-01
QoS Commands
service-policy (Wired)
service-policy (Wired)
To apply a policy map to a physical port or a switch virtual interface (SVI), use the service-policy command
in interface configuration mode. Use the no form of this command to remove the policy map and port
association.
service-policy {input | output} policy-map-name
no service-policy {input | output} policy-map-name
Syntax Description
input policy-map-name
Apply the specified policy map to the input of a physical port or an
SVI.
output policy-map-name
Apply the specified policy map to the output of a physical port or
an SVI.
Command Default
No policy maps are attached to the port.
Command Modes
WLAN interface configuration
Command History
Usage Guidelines
Release
Modification
Cisco IOS XE 3.2SE
This command was introduced.
A policy map is defined by the policy map command.
Only one policy map is supported per port, per direction. In other words, only one input policy and one output
policy is allowed on any one port.
You can apply a policy map to incoming traffic on a physical port or on an SVI. QoS Configuration Guide
(Cisco WLC 5700 Series).
Note
Examples
Though visible in the command-line help strings, the history keyword is not supported, and you should
ignore the statistics that it gathers.
This example shows how to apply plcmap1 to an physical ingress port:
Controller(config)# interface gigabitethernet2/0/1
Controller(config-if)# service-policy input plcmap1
QoS Command Reference, Cisco IOS XE 3E (Cisco WLC 5700 Series)
OL-32321-01
37
QoS Commands
service-policy (Wired)
This example shows how to remove plcmap2 from a physical port:
Controller(config)# interface gigabitethernet2/0/2
Controller(config-if)# no service-policy input plcmap2
The following example displays a VLAN policer configuration. At the end of this configuration, the VLAN
policy map is applied to an interface for QoS:
Controller# configure terminal
Controller(config)# class-map vlan100
Controller(config-cmap)# match vlan 100
Controller(config-cmap)# exit
Controller(config)# policy-map vlan100
Controller(config-pmap)# policy-map class vlan100
Controller(config-pmap-c)# police 100000 bc conform-action transmit exceed-action drop
Controller(config-pmap-c-police)# end
Controller# configure terminal
Controller(config)# interface gigabitEthernet1/0/5
Controller(config-if)# service-policy input vlan100
You can verify your settings by entering the show running-config privileged EXEC command.
Related Commands
Command
Description
policy-map
Creates or modifies a policy map that can be attached to multiple physical
ports or SVIs and enters policy-map configuration mode.
show policy-map
Displays QoS policy maps.
QoS Command Reference, Cisco IOS XE 3E (Cisco WLC 5700 Series)
38
OL-32321-01
QoS Commands
service-policy (WLAN)
service-policy (WLAN)
To configure the WLAN quality of service (QoS) service policy, use the service-policy command. To disable
a QoS policy on a WLAN, use the no form of this command.
service-policy [client] {input| output} policy-name
no service-policy [client] {input| output} policy-name
Syntax Description
client
(Optional) Assigns a policy map to all clients in the WLAN.
input
Assigns an input policy map.
output
Assigns an output policy map.
policy-name
The policy name.
Command Default
No policies are assigned and the state assigned to the policy is None.
Command Modes
WLAN configuration
Command History
Release
Modification
Cisco IOS XE 3.2SE
This command was introduced.
Usage Guidelines
You must disable the WLAN before using this command. See Related Commands section for more information
on how to disable a WLAN.
Examples
This example shows how to configure the input QoS service policy on a WLAN:
Controller# configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
Controller(config)# wlan wlan1
Controller(config-wlan)# service-policy input policy-test
This example shows how to disable the input QoS service policy on a WLAN:
Controller# configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
Controller(config)# wlan wlan1
Controller(config-wlan)# no service-policy input policy-test
This example shows how to configure the output QoS service policy on a WLAN to platinum (precious metal
policy):
Controller# configure terminal
Enter configuration commands, one per line.
End with CNTL/Z.
QoS Command Reference, Cisco IOS XE 3E (Cisco WLC 5700 Series)
OL-32321-01
39
QoS Commands
service-policy (WLAN)
Controller(config)# wlan wlan1
Controller(config-wlan)# service-policy output platinum
QoS Command Reference, Cisco IOS XE 3E (Cisco WLC 5700 Series)
40
OL-32321-01
QoS Commands
set
set
To classify IP traffic by setting a Differentiated Services Code Point (DSCP) or an IP-precedence value in
the packet, use the set command in policy-map class configuration mode. Use the no form of this command
to remove traffic classification.
set cos| dscp| precedence| ip| qos-group| wlan
set cos {cos-value } | {cos| dscp| precedence| qos-group| wlan} [table table-map-name]
set dscp {dscp-value } | {cos| dscp| precedence| qos-group| wlan} [table table-map-name]
set ip {dscp| precedence}
set precedence {precedence-value } | {cos| dscp| precedence| qos-group} [table table-map-name]
set qos-group {qos-group-value| dscp [table table-map-name]| precedence [table table-map-name]}
set wlan user-priorityuser-priority-value| costable table-map-name| dscptable table-map-name|
qos-grouptable table-map-name| wlantable table-map-name
QoS Command Reference, Cisco IOS XE 3E (Cisco WLC 5700 Series)
OL-32321-01
41
QoS Commands
set
Syntax Description
cos
Sets the Layer 2 class of service (CoS) value or user priority
of an outgoing packet. You can specify these values:
• cos-value—CoS value from 0 to 7. You also can enter
a mnemonic name for a commonly used value.
• Specify a packet-marking category to set the CoS
value of the packet. If you also configure a table map
for mapping and converting packet-marking values,
this establishes the "map from" packet-marking
category. Packet-marking category keywords:
◦cos—Sets a value from the CoS value or user
priority.
◦dscp—Sets a value from packet differentiated
services code point (DSCP).
◦precedence—Sets a value from packet
precedence.
◦qos-group—Sets a value from the QoS group.
◦wlan—Sets the WLAN user priority values.
• (Optional)table table-map-name—Indicates that the
values set in a specified table map are used to set the
CoS value. Enter the name of the table map used to
specify the CoS value. The table map name can be a
maximum of 64 alphanumeric characters.
If you specify a packet-marking category but do not
specify the table map, the default action is to copy
the value associated with the packet-marking category
as the CoS value. For example, if you enter the set
cos precedence command, the precedence
(packet-marking category) value is copied and used
as the CoS value.
QoS Command Reference, Cisco IOS XE 3E (Cisco WLC 5700 Series)
42
OL-32321-01
QoS Commands
set
dscp
Sets the differentiated services code point (DSCP) value
to mark IP(v4) and IPv6 packets. You can specify these
values:
• cos-value—Number that sets the DSCP value. The
range is from 0 to 63. You also can enter a mnemonic
name for a commonly used value.
• Specify a packet-marking category to set the DSCP
value of the packet. If you also configure a table map
for mapping and converting packet-marking values,
this establishes the "map from" packet-marking
category. Packet-marking category keywords:
◦cos—Sets a value from the CoS value or user
priority.
◦dscp—Sets a value from packet differentiated
services code point (DSCP).
◦precedence—Sets a value from packet
precedence.
◦qos-group—Sets a value from the QoS group.
◦wlan—Sets a value from WLAN.
• (Optional)table table-map-name—Indicates that the
values set in a specified table map will be used to set
the DSCP value. Enter the name of the table map
used to specify the DSCP value. The table map name
can be a maximum of 64 alphanumeric characters.
If you specify a packet-marking category but do not
specify the table map, the default action is to copy
the value associated with the packet-marking category
as the DSCP value. For example, if you enter the set
dscp cos command, the CoS value (packet-marking
category) is copied and used as the DSCP value.
ip
Sets IP values to the classified traffic. You can specify
these values:
• dscp—Specify an IP DSCP value from 0 to 63 or a
packet marking category.
• precedence—Specify a precedence-bit value in the
IP header; valid values are from 0 to 7 or specify a
packet marking category.
QoS Command Reference, Cisco IOS XE 3E (Cisco WLC 5700 Series)
OL-32321-01
43
QoS Commands
set
precedence
Sets the precedence value in the packet header. You can
specify these values:
• precedence-value— Sets the precedence bit in the
packet header; valid values are from 0 to 7. You also
can enter a mnemonic name for a commonly used
value.
• Specify a packet marking category to set the
precedence value of the packet.
◦cos—Sets a value from the CoS or user priority.
◦dscp—Sets a value from packet differentiated
services code point (DSCP).
◦precedence—Sets a value from packet
precedence.
◦qos-group—Sets a value from the QoS group.
• (Optional)table table-map-name—Indicates that the
values set in a specified table map will be used to set
the precedence value. Enter the name of the table map
used to specify the precedence value. The table map
name can be a maximum of 64 alphanumeric
characters.
If you specify a packet-marking category but do not
specify the table map, the default action is to copy
the value associated with the packet-marking category
as the precedence value. For example, if you enter
the set precedence cos command, the CoS value
(packet-marking category) is copied and used as the
precedence value.
QoS Command Reference, Cisco IOS XE 3E (Cisco WLC 5700 Series)
44
OL-32321-01
QoS Commands
set
qos-group
Assigns a QoS group identifier that can be used later to
classify packets.
• qos-group-value—Sets a QoS value to the classified
traffic. The range is 0 to 31. You also can enter a
mnemonic name for a commonly used value.
• dscp—Sets the original DSCP field value of the
packet as the QoS group value.
• precedence—Sets the original precedence field value
of the packet as the QoS group value.
• (Optional)table table-map-name—Indicates that the
values set in a specified table map will be used to set
the DSCP or precedence value. Enter the name of the
table map used to specify the value. The table map
name can be a maximum of 64 alphanumeric
characters.
If you specify a packet-marking category (dscp or
precedence) but do not specify the table map, the
default action is to copy the value associated with the
packet-marking category as the QoS group value. For
example, if you enter the set qos-group precedence
command, the precedence value (packet-marking
category) is copied and used as the QoS group value.
QoS Command Reference, Cisco IOS XE 3E (Cisco WLC 5700 Series)
OL-32321-01
45
QoS Commands
set
wlan user-priority wlan-user-priority
Assigns a WLAN user-priority to the classified traffic. You
can specify these values:
• wlan-user-priority—Sets a WLAN user priority to
the classified traffic. The range is 0 to 7.
• cos—Sets the Layer 2 CoS field value as the WLAN
user priority.
• dscp—Sets the DSCP field value as the WLAN user
priority.
• precedence—Sets the precedence field value as the
WLAN user priority.
• wlan—Sets the WLAN user priority field value as
the WLAN user priority.
• (Optional)table table-map-name—Indicates that the
values set in a specified table map will be used to set
the WLAN user priority value. Enter the name of the
table map used to specify the value. The table map
name can be a maximum of 64 alphanumeric
characters.
If you specify a packet-marking category but do not
specify the table map, the default action is to copy
the value associated with the packet-marking category
as the WLAN user priority. For example, if you enter
the set wlan user-priority cos command, the cos
value (packet-marking category) is copied and used
as the WLAN user priority.
Command Default
No traffic classification is defined.
Command Modes
Policy-map class configuration
Command History
Usage Guidelines
Release
Modification
Cisco IOS XE 3.2SE
This command was introduced.
Cisco IOS XE 3.3SE
The cos, dscp, qos-group, wlantable
table-map-name, keywords were added.
For the set dscp dscp-value command, the set cos cos-value command, and the set ip precedence
precedence-value command, you can enter a mnemonic name for a commonly used value. For example, you
QoS Command Reference, Cisco IOS XE 3E (Cisco WLC 5700 Series)
46
OL-32321-01
QoS Commands
set
can enter the set dscp af11 command, which is the same as entering the set dscp 10 command. You can enter
the set ip precedence critical command, which is the same as entering the set ip precedence 5 command.
For a list of supported mnemonics, enter the set dscp ? or the set ip precedence ? command to see the
command-line help strings.
When you configure the set dscp coscommand, note the following: The CoS value is a 3-bit field, and the
DSCP value is a 6-bit field. Only the three bits of the CoS field are used.
When you configure the set dscp qos-group command, note the following:
• The valid range for the DSCP value is a number from 0 to 63. The valid value range for the QoS group
is a number from 0 to 99.
• If a QoS group value falls within both value ranges (for example, 44), the packet-marking value is copied
and the packets is marked.
• If QoS group value exceeds the DSCP range (for example, 77), the packet-marking value is not be copied
and the packet is not marked. No action is taken.
The set qos-group command cannot be applied until you create a service policy in policy-map configuration
mode and then attach the service policy to an interface or ATM virtual circuit (VC).
To return to policy-map configuration mode, use the exit command. To return to privileged EXEC mode, use
the end command.
Examples
This example shows how to assign DSCP 10 to all FTP traffic without any policers:
Controller(config)# policy-map policy_ftp
Controller(config-pmap)# class-map ftp_class
Controller(config-cmap)# exit
Controller(config)# policy policy_ftp
Controller(config-pmap)# class ftp_class
Controller(config-pmap-c)# set dscp 10
Controller(config-pmap)# exit
You can verify your settings by entering the show policy-map privileged EXEC command.
Related Commands
Command
Description
class
Defines a traffic classification match criteria for the specified class-map name.
policy-map
Creates or modifies a policy map that can be attached to multiple physical
ports or SVIs and enters policy-map configuration mode.
show policy-map
Displays QoS policy maps.
QoS Command Reference, Cisco IOS XE 3E (Cisco WLC 5700 Series)
OL-32321-01
47
QoS Commands
show ap name service-policy
show ap name service-policy
To display service-policy information for a specific Cisco lightweight access point, use the show ap name
service-policy command.
show ap name ap-name service-policy
Syntax Description
ap-name
Name of the Cisco lightweight access point.
Command Default
None
Command Modes
Any command mode
Command History
Examples
Release
Modification
Cisco IOS XE 3.2SE
This command was introduced.
This example shows how to display service-policy information for a specific Cisco lightweight access point:
Controller# show ap name 3502b service-policy
AP Name
Port Policy Name
Port Policy State
: 3500(5760-1)
: unknown
: Installed
Radio Policies
Slot# Radio
Policy
State
-------------------------------------------------------------------1
0
802.11b/g
def-11gn
Installed
2
1
802.11a
def-11an
Installed
BSSID Policies
Slot#
CfgState
Wlan-ID Wlan-Name
Down-Policy
State
Up-Policy
CfgState
State
-----------------------------------------------------------------------------------------------------------------1
0
Sent to AP
2
1
Sent to AP
1
1
wlan-test
ssid-out
wlan-test
ssid-out
ssid-up
Installed
None
ssid-up
Installed
None
Installed
Installed
QoS Command Reference, Cisco IOS XE 3E (Cisco WLC 5700 Series)
48
OL-32321-01
QoS Commands
show ap name dot11
show ap name dot11
To display 802.11a or 802.11b configuration information that corresponds to specific Cisco lightweight access
points, use the show ap name dot11 command.
show ap name ap-name dot11 {24ghz| 5ghz} {ccx| cdp| profile| service-poicy output| stats| tsm {all|
client-mac}}
Syntax Description
ap-name
Name of the Cisco lightweight access point.
24ghz
Displays the 2.4 GHz band.
5ghz
Displays the 5 GHz band.
ccx
Displays the Cisco Client eXtensions (CCX) radio management status
information.
cdp
Displays Cisco Discovery Protocol (CDP) information.
profile
Displays configuration and statistics of 802.11 profiling.
service-policy output
Displays downstream service policy information.
stats
Displays Cisco lightweight access point statistics.
tsm
Displays 802.11 traffic stream metrics statistics.
all
Displays the list of all access points to which the client has associations.
client-mac
MAC address of the client.
Command Default
None
Command Modes
Any command mode
Command History
Examples
Release
Modification
Cisco IOS XE 3.2SE
This command was introduced.
This example shows how to display the service policy that is associated with the access point:
Controller# show ap name test-ap dot11 24ghz service-policy output
QoS Command Reference, Cisco IOS XE 3E (Cisco WLC 5700 Series)
OL-32321-01
49
QoS Commands
show ap name dot11
Policy Name : test-ap1
Policy State : Installed
This example shows how to display the CCX RRM 802.11 configuration for a specific access point:
Controller# show ap name AP01 dot11 24ghz ccx
This example show how to display CDP information for a specific access point:
Controller# show ap name AP01 dot11 24ghz cdp
AP Name
AP CDP State
--------------------- -------------AP03
Disabled
This example show how to display the configuration and statistics of 802.11b profiling for a specific access
point:
Controller# show ap name AP01 dot11 24ghz profile
802.11b
802.11b
802.11b
802.11b
802.11b
802.11b
Cisco
Cisco
Cisco
Cisco
Cisco
Cisco
AP
AP
AP
AP
AP
AP
performance profile mode
Interference threshold
noise threshold
RF utilization threshold
throughput threshold
clients threshold
:
:
:
:
:
:
GLOBAL
10 %
-70 dBm
80 %
1000000 bps
12 clients
This example show how to display downstream service policy information for a specific access point:
Controller# show ap name AP01 dot11 24ghz service-policy output
Policy Name : def-11gn
Policy State : Installed
This example show how to display statistics for a specific access point:
Controller# show ap name AP01 dot11 24ghz stats
Number of Users................................:
TxFragmentCount................................:
MulticastTxFrameCnt............................:
FailedCount....................................:
RetryCount.....................................:
MultipleRetryCount.............................:
FrameDuplicateCount............................:
RtsSuccessCount................................:
RtsFailureCount................................:
AckFailureCount................................:
RxIncompleteFragment...........................:
MulticastRxFrameCnt............................:
FcsErrorCount..................................:
TxFrameCount...................................:
WepUndecryptableCount..........................:
TxFramesDropped................................:
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Call Admission Control (CAC) Stats
Voice Bandwidth in use(% of config bw).........:
Video Bandwidth in use(% of config bw).........:
Total BW in use for Voice(%)...................:
Total BW in use for SIP Preferred call(%)......:
0
0
0
0
Load based Voice Call Stats
Total channel MT free..........................:
Total voice MT free............................:
Na Direct......................................:
Na Roam........................................:
0
0
0
0
WMM TSPEC CAC Call Stats
Total num of voice calls in progress...........: 0
Num of roaming voice calls in progress.........: 0
Total Num of voice calls since AP joined.......: 0
QoS Command Reference, Cisco IOS XE 3E (Cisco WLC 5700 Series)
50
OL-32321-01
QoS Commands
show ap name dot11
Total Num of roaming calls since AP joined.....:
Total Num of exp bw requests received..........:
Total Num of exp bw requests admitted..........:
Num of voice calls rejected since AP joined....:
Num of roam calls rejected since AP joined.....:
Num of calls rejected due to insufficent bw....:
Num of calls rejected due to invalid params....:
Num of calls rejected due to PHY rate..........:
Num of calls rejected due to QoS policy........:
0
0
0
0
0
0
0
0
0
SIP CAC Call Stats
Total Num of calls in progress.................:
Num of roaming calls in progress...............:
Total Num of calls since AP joined.............:
Total Num of roaming calls since AP joined.....:
Total Num of Preferred calls received..........:
Total Num of Preferred calls accepted..........:
Total Num of ongoing Preferred calls...........:
Total Num of calls rejected(Insuff BW).........:
Total Num of roam calls rejected(Insuff BW)....:
0
0
0
0
0
0
0
0
0
Band Select Stats
Num of dual band client .......................:
Num of dual band client added..................:
Num of dual band client expired ...............:
Num of dual band client replaced...............:
Num of dual band client detected ..............:
Num of suppressed client ......................:
Num of suppressed client expired...............:
Num of suppressed client replaced..............:
0
0
0
0
0
0
0
0
This example show how to display the traffic stream configuration for all clients that correspond to a specific
access point:
Controller# show ap name AP01 dot11 24ghz tsm all
QoS Command Reference, Cisco IOS XE 3E (Cisco WLC 5700 Series)
OL-32321-01
51
QoS Commands
show class-map
show class-map
To display quality of service (QoS) class maps, which define the match criteria to classify traffic, use the
show class-map command in EXEC mode.
show class-map [class-map-name | type control subscriber {all | class-map-name}]
Syntax Description
Command Modes
class-map-name
(Optional) Class map name.
type control subscriber
(Optional) Displays information about control class maps.
all
(Optional) Displays information about all control class maps.
User EXEC
Privileged EXEC
Command History
Examples
Release
Modification
Cisco IOS XE 3.2SE
This command was introduced.
This is an example of output from the show class-map command:
Controller# show class-map
Class Map match-any videowizard_10-10-10-10 (id 2)
Match access-group name videowizard_10-10-10-10
Class Map match-any class-default (id 0)
Match any
Class Map match-any dscp5 (id 3)
Match ip dscp 5
Related Commands
Command
Description
class-map
Creates a class map to be used for matching packets to the class whose name
you specify and enters class-map configuration mode.
QoS Command Reference, Cisco IOS XE 3E (Cisco WLC 5700 Series)
52
OL-32321-01
QoS Commands
show wireless client calls
show wireless client calls
To display the total number of active or rejected calls on the controller, use the show wireless client calls
command in privileged EXEC mode.
show wireless client calls {active | rejected}
Syntax Description
active
Displays active calls.
rejected
Displays rejected calls.
Command Default
No default behavior or values.
Command Modes
Privileged EXEC
Command History
Examples
Release
Modification
Cisco IOS XE 3.2SE
This command was introduced.
The following is sample output from the show wireless client calls command:
controller# show wireless client calls active
TSPEC Calls:
---------------------------------------------------------------------------MAC Address
AP Name
Status
WLAN Authenticated
----------------------------------------------------------------------------0000.1515.000f
AP-2
Associated
1 Yes
SIP Calls:
-----------------Number of Active TSPEC calls on 802.11a and 802.11b/g: 1
Number of Active SIP calls on 802.11a and 802.11b/g: 0
QoS Command Reference, Cisco IOS XE 3E (Cisco WLC 5700 Series)
OL-32321-01
53
QoS Commands
show wireless client dot11
show wireless client dot11
To display the total number of active or rejected calls for a specific band (2.4 Ghz or 5 Ghz), use the show
wireless client dot11 command in privileged EXEC mode.
show wireless client dot11 {24ghz | 5ghz} calls {active | rejected}
Syntax Description
24ghz
Displays the 802.11b/g network.
5ghz
Displays the 802.11a network.
calls
Displays the wireless client calls.
active
Displays active calls.
rejected
Displays rejected calls.
Command Default
No default behavior or values.
Command Modes
Privileged EXEC
Command History
Examples
Release
Modification
Cisco IOS XE 3.2SE
This command was introduced.
The following is sample output from the show wireless client dot11 command:
Controller# show wireless client dot11 5ghz calls active
TSPEC Calls:
-----------------SIP Calls:
-----------------Number of Active TSPEC calls on 802.11a: 0
Number of Active SIP calls on 802.11a: 0
QoS Command Reference, Cisco IOS XE 3E (Cisco WLC 5700 Series)
54
OL-32321-01
QoS Commands
show wireless client mac-address (Call Control)
show wireless client mac-address (Call Control)
To view call control information related to clients, use the show wireless client mac-address command in
privileged EXEC mode.
show wireless client mac-address mac-address call-control call-info
Syntax Description
mac-address
The client MAC address.
call-control call-info
Displays the call control and IP-related information about a client.
Command Default
None
Command Modes
Privileged EXEC
Command History
Examples
Release
Modification
Cisco IOS XE 3.2SE
This command was introduced.
This example shows how to display call control and IP-related information about a client:
Controller# show wireless client mac-address
Client MAC Address
: 30E4DB416157
30e4.db41.6157 call-control call-info
Call 1 Statistics
Uplink IP Address
Downlink IP Address
Uplink Port
Downlink Port
Call ID
Called Party
Calling Party
Priority
Call On Hold
Call Duration
:
:
:
:
:
:
:
:
:
:
209.165.200.225
209.165.200.226
29052
27538
c40acb4d-3b3b0.3d27da1e-356bed03
sip:1011
sip:1012
6
false
30
Call 2 Statistics
No Active Call
QoS Command Reference, Cisco IOS XE 3E (Cisco WLC 5700 Series)
OL-32321-01
55
QoS Commands
show wireless client mac-address (TCLAS)
show wireless client mac-address (TCLAS)
To view information about TCLAS and user priority, use the show wireless client mac-address command
in privileged EXEC mode.
show wireless client mac-address mac-address tclas
Syntax Description
Command Modes
Command History
Examples
mac-address
The client MAC address.
tclas
Displays TCLAS and user priority-related information about a client.
Privileged EXEC
Release
Modification
Cisco IOS XE 3.2SE
This command was introduced.
This example shows how to display the TCLAS and user priority-related information about a client:
Controller# show wireless client mac-address 30e4.db41.6157 tclas
MAC Address
UP TID Mask Source IP Addr Dest IP Addr
SrcPort DstPort Proto
---------------------------------------------------------------------------------30e4.db41.6157
4
4
95 167838052
2164326668
5060
5060
6
30e4.db41.6157
6
1
31 0
2164326668
0
27538
17
QoS Command Reference, Cisco IOS XE 3E (Cisco WLC 5700 Series)
56
OL-32321-01
QoS Commands
show wireless client mac-address service-policy
show wireless client mac-address service-policy
To view the details of the client policy for a client, use the show wireless client mac-address service-policy
command in privileged EXEC mode.
show wireless client mac-address mac-address service-policy {input | output}
Syntax Description
mac-address
Client MAC address.
input
Displays the details of the input client policy.
output
Displays the details of the output client policy.
Command Default
None
Command Modes
Privileged EXEC
Command History
Examples
Release
Modification
Cisco IOS XE 3E
This command was introduced.
This example shows how to display the details of the client policy:
Controller# show wireless client mac-address 30e4.db41.6157 service-policy input
Wireless Client QoS Service Policy
Status Summary Information
Policy Name : client-up
Policy State : Installed
Policy Source : CLI Policy
Status Internal Information
Policy Name Sent to AP : client-up
AP to which Policy Name was Sent : 3500(5760-1)
Policy Content Status : Sent to AP
Detailed Status String from AP : Policy Name: client-up.Policy created successfully.Client
Policy bind successfu
Detailed Status String from IOSd : OK
Related Commands
Command
Description
show wireless client mac-address (Call Control) Displays details of call control information related to the
client.
QoS Command Reference, Cisco IOS XE 3E (Cisco WLC 5700 Series)
OL-32321-01
57
QoS Commands
show wireless client mac-address service-policy
Command
Description
show wireless client mac-address (TCLAS)
Displays TCLAS and user priority related information about
to a client.
QoS Command Reference, Cisco IOS XE 3E (Cisco WLC 5700 Series)
58
OL-32321-01
QoS Commands
show wireless client voice diagnostics
show wireless client voice diagnostics
To display wireless client voice diagnostic parameters, use the show wireless client voice diagnostics command
in privileged EXEC mode.
show wireless client voice diagnostics {qos-map | roam-history | rssi | status | tspec}
Syntax Description
qos-map
Displays information about the QoS and DSCP mapping and packet statistics in
each of the four queues: VO, VI, BE, BK. The different DSCP values are also
displayed.
roam-history
Displays information about the last 3 roaming histories for each known client. The
output contains the timestamp, access point associated with roaming, roaming reason,
and if there is a roaming failure, a reason for the roaming failure.
rssi
Displays the client's RSSI values in the last 5 seconds when voice diagnostics are
enabled.
status
Displays status of voice diagnostics for clients.
tspec
Displays voice diagnostics that are enabled for TSPEC clients.
Command Default
No default behavior or values.
Command Modes
Privileged EXEC
Command History
Release
Modification
Cisco IOS XE 3.2SE
This command was introduced.
Usage Guidelines
Debug voice diagnostics must be enabled for voice diagnostics to work.
Examples
The following is sample output from the show wireless client voice diagnostics status command:
Controller# show wireless client voice diagnostics status
Voice Diagnostics Status: FALSE
QoS Command Reference, Cisco IOS XE 3E (Cisco WLC 5700 Series)
OL-32321-01
59
QoS Commands
show policy-map
show policy-map
To display quality of service (QoS) policy maps, which define classification criteria for incoming traffic, use
the show policy-map command in EXEC mode.
show policy-map [policy-map-name| interface interface-id]
show policy-map interface {Auto-template | Capwap | GigabitEthernet | GroupVI | InternalInterface |
Loopback | Lspvif | Null | Port-channel | TenGigabitEthernet | Tunnel | Vlan | brief | class | input | output
show policy-map type control subscriber detail
show policy-map interface wireless {ap name ap_name | client mac mac_address | radio type {24ghz |
5ghz} ap name ap_name | ssid name ssid_name {ap name ap_name | radio type {24ghz | 5ghz} ap name
ap_name}}
Syntax Description
Command Modes
policy-map-name
(Optional) Name of the policy-map.
interface interface-id
(Optional) Displays the statistics and the configurations of the input
and output policies that are attached to the interface.
type control subscriber detail
(Optional) Identifies the type of QoS policy and the statistics.
ap name ap_name
Displays SSID policy configuration of an access point.
client mac mac_address
Displays information about the policies for all the client targets.
radio type {24ghz | 5ghz
Displays policy configuration of the access point in the specified
radio type.
ssid name ssid_name
Displays policy configuration of an SSID.
User EXEC
Privileged EXEC
Command History
Release
Modification
Cisco IOS XE 3.2SE
This command was introduced.
Cisco IOS XE 3.3SE
The interface interface-id keyword was added.
QoS Command Reference, Cisco IOS XE 3E (Cisco WLC 5700 Series)
60
OL-32321-01
QoS Commands
show policy-map
Usage Guidelines
Note
Policy maps can include policers that specify the bandwidth limitations and the action to take if the limits are
exceeded.
Though visible in the command-line help string, the control-plane, session, and type keywords are not
supported, and the statistics shown in the display should be ignored.
To display classification counters for ternary content addressable memory (TCAM) (marking or policing)
based policies, enter the interface ID. Classification counters have the following restrictions:
• Classification counters are supported only on wired ports (in the ingress and egress directions).
• Classification counters count packets instead of bytes.
• Only QoS configurations with marking or policing trigger the classification counter.
• As long as there is policing or marking action in the policy, the class-default will have classification
counters.
• Classification counters are not port based. The counters are shared across targets sharing the same
policy map. This means that the classification counter aggregates all packets belonging to the same
class of the same policy which attach to different interfaces.
Examples
This is an example of output from the show policy-map interface command, where classification counters
are displayed:
Controller# show policy-map interface gigabitethernet1/0/1
GigabitEthernet1/0/1
Service-policy input: AutoQos-4.0-CiscoPhone-Input-Policy
Class-map: AutoQos-4.0-Voip-Data-CiscoPhone-Class (match-any)
0 packets
Match: cos 5
0 packets, 0 bytes
5 minute rate 0 bps
QoS Set
dscp ef
police:
cir 128000 bps, bc 8000 bytes
conformed 0 bytes; actions:
transmit
exceeded 0 bytes; actions:
set-dscp-transmit dscp table policed-dscp
conformed 0000 bps, exceed 0000 bps
Class-map: AutoQos-4.0-Voip-Signal-CiscoPhone-Class (match-any)
0 packets
Match: cos 3
0 packets, 0 bytes
5 minute rate 0 bps
QoS Set
dscp cs3
police:
cir 32000 bps, bc 8000 bytes
conformed 0 bytes; actions:
transmit
exceeded 0 bytes; actions:
set-dscp-transmit dscp table policed-dscp
QoS Command Reference, Cisco IOS XE 3E (Cisco WLC 5700 Series)
OL-32321-01
61
QoS Commands
show policy-map
conformed 0000 bps, exceed 0000 bps
Class-map: AutoQos-4.0-Default-Class (match-any)
0 packets
Match: access-group name AutoQos-4.0-Acl-Default
0 packets, 0 bytes
5 minute rate 0 bps
QoS Set
dscp default
Class-map: class-default (match-any)
0 packets
Match: any
0 packets, 0 bytes
5 minute rate 0 bps
Service-policy output: AutoQos-4.0-Output-Policy
queue stats for all priority classes:
Queueing
priority level 1
(total drops) 0
(bytes output) 0
Class-map: AutoQos-4.0-Output-Priority-Queue (match-any)
0 packets
Match: dscp cs4 (32) cs5 (40) ef (46)
0 packets, 0 bytes
5 minute rate 0 bps
Match: cos 5
0 packets, 0 bytes
5 minute rate 0 bps
Priority: 30% (300000 kbps), burst bytes 7500000,
Priority Level: 1
Class-map: AutoQos-4.0-Output-Control-Mgmt-Queue (match-any)
0 packets
Match: dscp cs2 (16) cs3 (24) cs6 (48) cs7 (56)
0 packets, 0 bytes
5 minute rate 0 bps
Match: cos 3
0 packets, 0 bytes
5 minute rate 0 bps
Queueing
queue-limit dscp 16 percent 80
queue-limit dscp 24 percent 90
queue-limit dscp 48 percent 100
queue-limit dscp 56 percent 100
(total drops) 0
(bytes output) 0
bandwidth remaining 10%
queue-buffers ratio 10
Class-map: AutoQos-4.0-Output-Multimedia-Conf-Queue (match-any)
0 packets
Match: dscp af41 (34) af42 (36) af43 (38)
0 packets, 0 bytes
5 minute rate 0 bps
Match: cos 4
0 packets, 0 bytes
5 minute rate 0 bps
Queueing
(total drops) 0
(bytes output) 0
bandwidth remaining 10%
queue-buffers ratio 10
Class-map: AutoQos-4.0-Output-Trans-Data-Queue (match-any)
QoS Command Reference, Cisco IOS XE 3E (Cisco WLC 5700 Series)
62
OL-32321-01
QoS Commands
show policy-map
0 packets
Match: dscp af21 (18) af22 (20) af23 (22)
0 packets, 0 bytes
5 minute rate 0 bps
Match: cos 2
0 packets, 0 bytes
5 minute rate 0 bps
Queueing
(total drops) 0
(bytes output) 0
bandwidth remaining 10%
queue-buffers ratio 10
Class-map: AutoQos-4.0-Output-Bulk-Data-Queue (match-any)
0 packets
Match: dscp af11 (10) af12 (12) af13 (14)
0 packets, 0 bytes
5 minute rate 0 bps
Match: cos 1
0 packets, 0 bytes
5 minute rate 0 bps
Queueing
(total drops) 0
(bytes output) 0
bandwidth remaining 4%
queue-buffers ratio 10
Class-map: AutoQos-4.0-Output-Scavenger-Queue (match-any)
0 packets
Match: dscp cs1 (8)
0 packets, 0 bytes
5 minute rate 0 bps
Queueing
(total drops) 0
(bytes output) 0
bandwidth remaining 1%
queue-buffers ratio 10
Class-map: AutoQos-4.0-Output-Multimedia-Strm-Queue (match-any)
0 packets
Match: dscp af31 (26) af32 (28) af33 (30)
0 packets, 0 bytes
5 minute rate 0 bps
Queueing
(total drops) 0
(bytes output) 0
bandwidth remaining 10%
queue-buffers ratio 10
Class-map: class-default (match-any)
0 packets
Match: any
0 packets, 0 bytes
5 minute rate 0 bps
Queueing
(total drops) 0
(bytes output) 0
bandwidth remaining 25%
queue-buffers ratio 25
This is an example of output from the show policy-map interface wireless ssid command: c
Controller# show policy-map interface wireless ssid name wlan-test radio type 5ghz ap name
3500_5760_1
SSID wlan-test iifid: 0x0107C300000000B1.0x0052DD400000002E.0x007000C00000005E
Service-policy input: ssid-up
QoS Command Reference, Cisco IOS XE 3E (Cisco WLC 5700 Series)
OL-32321-01
63
QoS Commands
show policy-map
Counters last updated 00:01:05 ago
Class-map: voice (match-any)
696388 packets
Match: dscp ef (46)
696388 packets, 982854241 bytes
30 second rate 30032000 bps
QoS Set
dscp cs5
Packets marked: 721710
police:
cir 5000000 bps, bc 156250 bytes
conformed 120836 packets, 170184920 bytes; actions:
transmit
exceeded 600874 packets, 848421317 bytes; actions:
drop
conformed 4870000 bps, exceeded 24383000 bps
Class-map: class-default (match-any)
1 packets
Match: any
QoS Set
dscp wlan user-priority table up2dscp
Packets marked: 1
police:
cir 10000000 bps, bc 312500 bytes
conformed 1 packets, 390 bytes; actions:
transmit
exceeded 0 packets, 0 bytes; actions:
drop
conformed 0000 bps, exceeded 0000 bps
Service-policy output: ssid-out
Class-map: class-default (match-any)
Match: any
shape (average) cir 100000000, bc 400000, be 400000
target shape rate 100000000
QoS Set
wlan user-priority dscp table dscp2up
Related Commands
Command
Description
policy-map
Creates or modifies a policy map that can be attached to multiple physical ports
or SVIs and enters policy-map configuration mode.
QoS Command Reference, Cisco IOS XE 3E (Cisco WLC 5700 Series)
64
OL-32321-01
QoS Commands
show wlan
show wlan
To view WLAN parameters, use the show wlan command.
show wlan {all | id wlan-id| name wlan-name | summary}
Syntax Description
all
Displays a summary of parameters of all configured WLANs.
The list is ordered by the ascending order of the WLAN IDs.
id wlan-id
Specifies the wireless LAN identifier. The range is from 1 to
512.
name wlan-name
Specifies the WLAN profile name. The name is from 1 to 32
characters.
summary
Displays a summary of the parameters configured on a WLAN.
Command Default
None
Command Modes
Global configuration
Command History
Examples
Release
Modification
Cisco IOS XE 3.2SE
This command was introduced.
This example shows how to display a summary of the WLANs configured on the device:
Controller# show wlan summary
Number of WLANs: 1
WLAN Profile Name
SSID
VLAN Status
-------------------------------------------------------------------------------45
test-wlan
test-wlan-ssid
1
UP
This example shows how to display a summary of parameters configured on a particular WLAN:
Controller# show wlan name test-wlan
WLAN Identifier
Profile Name
Network Name (SSID)
Status
Broadcast SSID
Maximum number of Associated Clients
AAA Policy Override
Network Admission Control
NAC-State
Number of Active Clients
Exclusionlist Timeout
:
:
:
:
:
:
:
45
test-wlan
test-wlan-ssid
Enabled
Enabled
0
Disabled
: Disabled
: 0
: 60
QoS Command Reference, Cisco IOS XE 3E (Cisco WLC 5700 Series)
OL-32321-01
65
QoS Commands
show wlan
Session Timeout
CHD per WLAN
Webauth DHCP exclusion
Interface
Interface Status
Multicast Interface
WLAN IPv4 ACL
WLAN IPv6 ACL
DHCP Server
DHCP Address Assignment Required
DHCP Option 82
DHCP Option 82 Format
DHCP Option 82 Ascii Mode
DHCP Option 82 Rid Mode
QoS Service Policy - Input
Policy Name
Policy State
QoS Service Policy - Output
Policy Name
Policy State
QoS Client Service Policy
Input Policy Name
Output Policy Name
WifiDirect
WMM
Channel Scan Defer Priority:
Priority (default)
Priority (default)
Priority (default)
Scan Defer Time (msecs)
Media Stream Multicast-direct
CCX - AironetIe Support
CCX - Gratuitous ProbeResponse (GPR)
CCX - Diagnostics Channel Capability
Dot11-Phone Mode (7920)
Wired Protocol
Peer-to-Peer Blocking Action
Radio Policy
DTIM period for 802.11a radio
DTIM period for 802.11b radio
Local EAP Authentication
Mac Filter Authorization list name
Accounting list name
802.1x authentication list name
Security
802.11 Authentication
Static WEP Keys
802.1X
Wi-Fi Protected Access (WPA/WPA2)
WPA (SSN IE)
WPA2 (RSN IE)
TKIP Cipher
AES Cipher
Auth Key Management
802.1x
PSK
CCKM
IP Security
IP Security Passthru
L2TP
Web Based Authentication
Conditional Web Redirect
Splash-Page Web Redirect
Auto Anchor
Sticky Anchoring
Cranite Passthru
Fortress Passthru
PPTP
Infrastructure MFP protection
Client MFP
Webauth On-mac-filter Failure
Webauth Authentication List Name
Webauth Parameter Map
:
:
:
:
:
:
:
:
:
:
:
:
:
:
1800 seconds
Enabled
Disabled
default
Up
test
test
unconfigured
Default
Disabled
Disabled
ap-mac
Disabled
Disabled
: unknown
: None
: unknown
: None
:
:
:
:
unknown
unknown
Disabled
Disabled
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
4
5
6
100
Disabled
Enabled
Disabled
Disabled
Invalid
None
Disabled
All
1
1
Disabled
Disabled
Disabled
Disabled
:
:
:
:
:
:
:
:
Open System
Disabled
Disabled
Enabled
Disabled
Enabled
Disabled
Enabled
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
Enabled
Disabled
Disabled
Disabled
Disabled
Disabled
Disabled
Disabled
Disabled
Disabled
Enabled
Disabled
Disabled
Disabled
Enabled
Optional
Disabled
Disabled
Disabled
QoS Command Reference, Cisco IOS XE 3E (Cisco WLC 5700 Series)
66
OL-32321-01
QoS Commands
show wlan
Tkip MIC Countermeasure Hold-down Timer
Call Snooping
Passive Client
Non Cisco WGB
Band Select
Load Balancing
IP Source Guard
Netflow Monitor
Direction
Traffic
:
:
:
:
:
:
:
:
:
:
60
Disabled
Disabled
Disabled
Disabled
Disabled
Disabled
test
Input
Datalink
Mobility Anchor List
IP Address
-----------
QoS Command Reference, Cisco IOS XE 3E (Cisco WLC 5700 Series)
OL-32321-01
67
QoS Commands
show wlan qos service-policies
show wlan qos service-policies
To view the SSID and client policies configured on all the WLANs, use the show wlan qos service-policies
command in privileged EXEC mode.
show wlan qos service-policies
Syntax Description
This command has no arguments or keywords.
Command Default
None
Command Modes
Privileged EXEC
Command History
Examples
Release
Modification
Cisco IOS XE 3E
This command was introduced.
This example shows how to view the SSID policies configured on all WLANs:
Controller# show wlan qos service-policies
Number of WLANs: 1
WLAN SSID Input
SSID Output
Client Input
Client
Output
-----------------------------------------------------------------------------------------------------------1
ssid-up
ssid-out
client-up
client-out
Related Commands
Command
Description
show ap name service-policy
Displays service-policy information for a specific access point.
QoS Command Reference, Cisco IOS XE 3E (Cisco WLC 5700 Series)
68
OL-32321-01
QoS Commands
trust device
trust device
To configure trust for supported devices connected to an interface, use the trust device command in interface
configuration mode. Use the no form of this command to disable trust for the connected device.
trust device {cisco-phone | cts | ip-camera | media-player}
no trust device {cisco-phone | cts | ip-camera | media-player}
Syntax Description
cisco-phone
Configures a Cisco IP phone
cts
Configures a Cisco TelePresence System
ip-camera
Configures an IP Video Surveillance Camera (IPVSC)
media-player
Configures a Cisco Digital Media Player (DMP)
Command Default
Trust disabled
Command Modes
Interface configuration
Command History
Usage Guidelines
Release
Modification
Cisco IOS XE 3.2SE
This command was introduced.
Use the trust device command on the following types of interfaces:
• Auto— auto-template interface
• Capwap—CAPWAP tunnel interface
• GigabitEthernet—Gigabit Ethernet IEEE 802
• GroupVI—Group virtual interface
• Internal Interface—Internal interface
• Loopback—Loopback interface
• Null—Null interface
• Port-channel—Ethernet Channel interface
• TenGigabitEthernet--10-Gigabit Ethernet
• Tunnel—Tunnel interface
QoS Command Reference, Cisco IOS XE 3E (Cisco WLC 5700 Series)
OL-32321-01
69
QoS Commands
trust device
• Vlan—Catalyst VLANs
• range—interface range command
Examples
The following example configures trust for a Cisco IP phone in Interface GigabitEthernet 1/0/1:
Controller(config)# interface GigabitEthernet1/0/1
Controller(config-if)# trust device cisco-phone
You can verify your settings by entering the show interface status privileged EXEC command.
QoS Command Reference, Cisco IOS XE 3E (Cisco WLC 5700 Series)
70
OL-32321-01
QoS Commands
wireless qos statistics
wireless qos statistics
To enable QoS statistics, use the wirelss qos statistics command. To disable the QoS statistics, use the no
form of the command.
wirelss qos statistics
Syntax Description
This command has no arguments or keywords.
Command Default
Enabled.
Command Modes
Global configuration
Command History
Release
Modification
Cisco IOS XE 3.6E
This command was introduced.
Usage Guidelines
Statistics are supported only for ingress policies with a maximum of five classes on wireless targets. For very
large policies, statistics for ingress policies are not visible at the controller. The frequency of the statistics
depends on the number of clients associated with the access point. Maximum time for the client statistics to
appear at the controller is around 5 minutes.
Examples
This example shows how to enable QoS statistics:
Controller(config)# wirelss qos statistics
QoS Command Reference, Cisco IOS XE 3E (Cisco WLC 5700 Series)
OL-32321-01
71
QoS Commands
wireless qos statistics
QoS Command Reference, Cisco IOS XE 3E (Cisco WLC 5700 Series)
72
OL-32321-01
INDEX
C
Q
class command 16
class-map command 19
queue-limit command 33
S
M
match (class-map configuration) command 21
match non-client-nrt command 24
match wlan user-priority command 25
P
policy-map command 26
service-policy command 37, 39
set command 41
show ap name dot11 49
show ap name service-policy 48
show class-map command 52
show policy-map command 60
show wireless client calls command 53
show wireless client dot11 command 54
show wireless client mac-address command 55, 56
show wireless client mac-address service-policy command 57
show wireless client voice diagnostics command 59
show wlan command 65
QoS Command Reference, Cisco IOS XE 3E (Cisco WLC 5700 Series)
OL-32321-01
IN-1
Index
QoS Command Reference, Cisco IOS XE 3E (Cisco WLC 5700 Series)
IN-2
OL-32321-01