Important Electrostatic Discharge and System
Grounding Information for Cisco SCE 8000,
Release 4.1.x
December 23, 2013
Release: 4.1.0
OL-30630-01
Note
This document supports all 4.1.x releases.
Overview
Before you install the Cisco SCE8000 chassis or touch the modules, read this document.
For more information on installing the Cisco SCE8000 platform, see either the Cisco SCE8000 10GBE
Installation and Configuration Guide or the Cisco SCE8000 GBE Installation and Configuration Guide.
For information regarding configuring the Cisco SCE8000 platform, see either the Cisco SCE8000
10GBE Software Configuration Guide or the Cisco SCE8000 GBE Software Configuration Guide.
Cisco Systems, Inc.
www.cisco.com
Preparing Your Location
Preparing Your Location
Make sure that your building is correctly grounded to earth ground.
Important Electrostatic Discharge and System Grounding Information for Cisco SCE 8000, Release 4.1.x
2
OL-30630-01
187876
Preparing Your Location
Earth ground
Important Electrostatic Discharge and System Grounding Information for Cisco SCE 8000, Release 4.1.x
OL-30630-01
3
Preparing the Rack Room
Preparing the Rack Room
Make sure that the rack enclosures are properly connected to the building earth ground.
•
Make sure that the chassis is kept in a sealed antistatic bag prior to installation.
187877
•
Chassis protected
in anti-static bag
Earth ground
Important Electrostatic Discharge and System Grounding Information for Cisco SCE 8000, Release 4.1.x
4
OL-30630-01
Preparing Yourself
Preparing Yourself
187878
Make sure that you are properly grounded before you remove the antistatic bag from the chassis.
Earth ground
Important Electrostatic Discharge and System Grounding Information for Cisco SCE 8000, Release 4.1.x
OL-30630-01
5
Precautions When Unpacking a Chassis
Precautions When Unpacking a Chassis
187879
Make sure you are properly grounded when removing the antistatic bag from the chassis.
Earth ground
Important Electrostatic Discharge and System Grounding Information for Cisco SCE 8000, Release 4.1.x
6
OL-30630-01
Precautions When Installing a Chassis
Precautions When Installing a Chassis
187880
Make sure that you are properly grounded and that you properly handle the chassis during installation.
Earth ground
Important Electrostatic Discharge and System Grounding Information for Cisco SCE 8000, Release 4.1.x
OL-30630-01
7
Grounding the Chassis
Grounding the Chassis
•
Make sure you properly connect the chassis (system) ground to the building ground.
•
The chassis illustration below shows the system ground connector pad location for the Cisco
SCE8000 chassis.
•
The ground lug kit part number is 69-0815-01.
FAN STATU
SCM
SCE8000-SCM-E
S
1
OPTICAL
BYPASS
CONSOLE
PORT 1
10 100
1000
STATUS
LINK
ACTIVE
OPTICAL
BYPASS
SCE8000-SCM-E
OPTICAL
BYPASS
SCM
SCE8000
AUX
2
EXTENDED
SERVICE
PORT 2
10 100
1000
OPTICAL
BYPASS
LINK
ACTIVE
CONTROL
MODULE
MASTER
SYSTEM
POWER
CONSOLE
PORT 1
10 100
1000
STATUS
LINK
ACTIVE
OPTICAL
BYPASS
SCE8000-SIP
OPTICAL
BYPASS
SIP
3
SCE8000
AUX
INK
ACTIVE/L
EXTENDED
PORT 2
10 100
1000
LINK
ACTIVE
SERVICE
CONTROL
MODULE
MASTER
SYSTEM
POWER
S
STATU
INK
ACTIVE/L
SPA-1X10GE-L-V2
INK
ACTIVE/L
S
STATU
SPA-1X10GE-L-V2
4
SCE80
00-FAN
S
STATU
INK
ACTIVE/L
SPA-1X10GE-L-V2
TX
TX
TX
RX
TX
RX
RX
RX
OPTICAL
A
B
A
C
C
D
B
D
CTRL
S
STATU
SPA-1X10GE-L-V2
STATUS
BYPASS1
OPB-SCE
8K-MM
TX
TX
TX
RX
TX
RX
RX
RX
A
B
A
C
C
D
B
D
CTRL
STATUS
BYPASS2
OPB-SCE8
K-MM
274487
OPTICAL
Earth
ground
Important Electrostatic Discharge and System Grounding Information for Cisco SCE 8000, Release 4.1.x
8
OL-30630-01
Transporting Line Cards
Transporting Line Cards
Earth ground
187882
Keep the line card in a sealed antistatic bag when transporting.
Important Electrostatic Discharge and System Grounding Information for Cisco SCE 8000, Release 4.1.x
OL-30630-01
9
Handling Line Cards
•
Properly ground yourself before you remove the line card from the antistatic bag.
•
Handle the line card by the front panel and the metal carrier only.
Earth ground
Important Electrostatic Discharge and System Grounding Information for Cisco SCE 8000, Release 4.1.x
10
OL-30630-01
187883
Handling Line Cards
Removing and Installing Line Cards
Removing and Installing Line Cards
Make sure you are properly grounded before removing or installing line cards.
•
Make sure you properly handle the line card by the front panel and the metal carrier only.
187884
•
Earth ground
Important Electrostatic Discharge and System Grounding Information for Cisco SCE 8000, Release 4.1.x
OL-30630-01
11
Grounding the Work Surface
Grounding the Work Surface
Make sure that you and the work surface that you are placing the line card on are properly grounded.
•
Your wrist strap, the rack enclosure, and the work surface should all be attached to the building
ground.
Earth ground
274532
•
Important Electrostatic Discharge and System Grounding Information for Cisco SCE 8000, Release 4.1.x
12
OL-30630-01
Grounding the Work Surface
Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its affiliates in the U.S. and other countries. To view a list of
Cisco trademarks, go to this URL: www.cisco.com/go/trademarks. Third-party trademarks mentioned are the property of their respective owners. The
use of the word partner does not imply a partnership relationship between Cisco and any other company. (1110R)
Any Internet Protocol (IP) addresses used in this document are not intended to be actual addresses. Any examples, command display output, and
figures included in the document are shown for illustrative purposes only. Any use o f actual IP addresses in illustrative content is unintentional and
coincidental.
© 2013 Cisco Systems, Inc. All rights reserved.
Important Electrostatic Discharge and System Grounding Information for Cisco SCE 8000, Release 4.1.x
OL-30630-01
13
Grounding the Work Surface
Important Electrostatic Discharge and System Grounding Information for Cisco SCE 8000, Release 4.1.x
14
OL-30630-01