Release Notes for Cisco Prime Infrastructure
Plug and Play Gateway Patch 2.2.0.10
First Published: Feb 16, 2015
This Release Notes document contains the following sections:
•
Introduction, page 1
•
Compatibility Information, page 2
•
System Requirements, page 2
•
Installation Notes, page 2
•
PnP Gateway Patch Installation in High Availability Configuration, page 3
•
Caveats, page 4
•
Related Documentation, page 4
•
Obtaining Documentation and Submitting a Service Request, page 5
Introduction
The Cisco Prime Infrastructure Plug and Play Gateway Patch 2.2.0.10 provides TLS connection with
Prime Infrastructure 2.2.1.
Cisco Systems, Inc.
www.cisco.com
Compatibility Information
Compatibility Information
Cisco Prime Infrastructure
Plug and Play Gateway
Cisco Prime Infrastructure
Patch Release
Release-Supported Servers
Cisco Plug and Play Deployment
Application-Supported Releases
2.2.0.10
2.2 and 2.2.1
2.0.0.28
2.2.0.9
2.2
2.0.0.28
2.0.0.30
2.0 and 2.1
2.0.0.28
1.2.1.8
1.3.2
2.0.0.28
1.2.1.5
1.3 or 1.3.1
2.0.0.19
System Requirements
For information on hardware requirements, see the “Prime Infrastructure Plug and Play Gateway Server
Requirements” section of the Cisco Prime Infrastructure 2.2 Quick Start Guide.
The Cisco Prime Infrastructure Plug and Play Gateway 2.2.0.10 standalone server patch must be
installed on the Cisco Prime Infrastructure Plug and Play Gateway Server 2.2. If Prime Infrastructure is
upgraded from previous releases like 1.2, 1.2.1, 2.0, 2.1, use this patch after upgrading to Prime
Infrastructure 2.2/2.2.1.
Installation Notes
This section contains instructions for installing the Cisco Prime Infrastructure Plug and Play Gateway.
Plug and Play Gateway Patch Installation in Standalone Configuration
The Plug and Play Gateway standalone server patch is available in the pnp-packaging-2.2.0.10.tar.gz
file. The patch upgrade procedure requires an FTP or TFTP server containing the patch file.
You can access this server from the Cisco Prime Infrastructure 2.2 Plug and Play Gateway standalone
server by following these steps:
1.
Log in to the Plug and Play Gateway standalone server as admin user. The following is a sample
output of the patch upgrade with the url FTP:
pnp-server login: admin
Password:
pnp-server/admin# configure Enter configuration commands, one per line. End with
CNTL/Z. pnp-server/admin(config)# repository <repository-name>
pnp-server/admin(config-Repository)# url ftp://<server-host-name>/<folder-location>
pnp-server/admin(config-Repository)# user <user-ID> password <option> <password>
pnp-server/admin(config-Repository)# exit
pnp-server/admin(config)# exit
2.
Use the application upgrade command to install the pnp-packaging-2.2.0.10.tar.gz Plug and Play
Gateway standalone patch. The following is a sample output of the pnp gateway patch upgrade:
bgl-dt-ncs-vm64-228/admin# application upgrade pnp-packaging-2.2.0.10.tar.gz
repository_name
Release Notes for Cisco Prime Infrastructure Plug and Play Gateway Patch 2.2.0.10
2
PnP Gateway Patch Installation in High Availability Configuration
Save the current ADE-OS running configuration? (yes/no) [yes] ?
Generating configuration...
Saved the ADE-OS running configuration to startup successfully
Initiating Application Upgrade...
Stage 1 of 7: Transferring file ...
-- complete.
Stage 2 of 7: Unpacking file ...
-- complete.
Stage 3 of 7: Executing pre-install ...
-- complete.
Stage 4 of 7: Upgrading binaries ...
-- complete.
Restore the Version 2.2.0.10
Restoring on a new installation setup required
-----------------------------------------------Thu Feb 12 10:37:53 UTC 2015
Restore operation started
-----------------------------------------------Backup Filename used is /tmp/pnp_upgrade/20150212103704.pnp_backup.tar.gz
This upgrade requires a setup.
Setup Plug and Play Gateway before running any commands.
httpd is stopped
Monitoring process started.
Plug and Play Gateway start...................
Started Event Manager process
Starting tomcat...
Starting httpd:
[ OK ]
Starting CNS Gateway:
Start of Plug and Play Gateway Completed!!
Restore operation ended
-----------------------------------------------Starting application ...
-- complete.
Application upgrade successful
3.
Exit from the current terminal (shell) and re-login as admin user.
4.
In case of PnP gateway release prior to 2.2, execute the PnP setup command to reconfigure the PnP
standalone server and start the PnP process.Upgrading from PnP 2.2.0.9 to PnP 2.2.0.10 step is not
required.
PnP Gateway Patch Installation in High Availability
Configuration
If the PnP Gateway is configured in high availability mode then follow the below steps to upgrade the
patch on both primary/secondary servers,
Step 1
Stop primary pnp gateway server.
Step 2
Follow the step 2 , in Plug and Play Gateway Patch Installation in Standalone Configuration and install
the patch in primary server.
Step 3
After successful upgradation, start the primary pnp gateway server.
Step 4
Stop the secondary pnp gateway server.
Release Notes for Cisco Prime Infrastructure Plug and Play Gateway Patch 2.2.0.10
3
Caveats
Step 5
Follow the step 2, in Plug and Play Gateway Patch Installation in Standalone Configuration and install
the patch in secondary server.
Step 6
After successful upgradation, start the secondary pnp gateway server.
Caveats
This section lists the open and resolved caveats for Cisco Prime Infrastructure Plug and Play Gateway
Patch 2.2.0.10:
•
Open Caveats, page 4
•
Resolved Caveats, page 4
Open Caveats
There are no open caveats for Cisco Prime Infrastructure Plug and Play Gateway Patch 2.2.0.10.
Resolved Caveats
•
CSCus76397
Symptom: Standalone PnP gateway server SSL handshake fails while connecting to Prime
Infrastructure.
Conditions: If PnP tries to connect to Prime Infrastructure through SSL/SSLv3 it does not get
connected as the Prime Infrastructure side SSL is disabled for secure connections establishment.
Workaround: No workaround.
Related Documentation
You can access the following additional Cisco Prime Infrastructure documentation on Cisco.com:
•
Cisco Prime Infrastructure 2.2 Quick Start Guide
•
Cisco Prime Infrastructure 2.2 User Guide
Release Notes for Cisco Prime Infrastructure Plug and Play Gateway Patch 2.2.0.10
4
Obtaining Documentation and Submitting a Service Request
Obtaining Documentation and Submitting a Service Request
For information on obtaining documentation, submitting a service request, and gathering additional
information, see What’s New in Cisco Product Documentation at:
http://www.cisco.com/en/US/docs/general/whatsnew/whatsnew.html.
Subscribe to What’s New in Cisco Product Documentation, which lists all new and revised Cisco technical
documentation, as an RSS feed and deliver content directly to your desktop using a reader application. The
RSS feeds are a free service.
This document is to be used in conjunction with the documents listed in the “Related Documentation” section.
Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its affiliates in the U.S. and other countries. To view a list of
Cisco trademarks, go to this URL: www.cisco.com/go/trademarks. Third-party trademarks mentioned are the property of their respective owners. The
use of the word partner does not imply a partnership relationship between Cisco and any other company. (1110R)
Any Internet Protocol (IP) addresses and phone numbers used in this document are not intended to be actual addresses and phone numbers. Any
examples, command display output, network topology diagrams, and other figures included in the document are shown for illustrative purposes only.
Any use of actual IP addresses or phone numbers in illustrative content is unintentional and coincidental.
© 2015 Cisco Systems, Inc. All rights reserved.
Release Notes for Cisco Prime Infrastructure Plug and Play Gateway Patch 2.2.0.10
5
Obtaining Documentation and Submitting a Service Request
Release Notes for Cisco Prime Infrastructure Plug and Play Gateway Patch 2.2.0.10
6