Accessing Cisco StadiumVision Director
Release 2.3 and 2.4
March 2011
Corporate Headquarters
Cisco Systems, Inc.
170 West Tasman Drive
San Jose, CA 95134-1706
USA
http://www.cisco.com
Tel:
408 526-4000
800 553-NETS (6387)
Fax:
408 526-4100
Table of Contents
Document History ................................................................................................................................3
Accessing SV Director .........................................................................................................................4
Changing Your Cisco StadiumVision Director Password ..........................................................5
Logging Out of Cisco StadiumVision Director ............................................................................6
Assigning Login Credentials for Role Based Access Control ...................................................7
© 2011-2012 Cisco Systems, Inc.
Page 2 of 7
Document History
Table 1. Revision History
Date
Comments
03/09/2011
Updated for Cisco StadiumVision Director Release 2.3.
10/27/2010
First release.
NOTE: This document provides illustrations for Cisco StadiumVision Director
Release 2.3, but also applies to Cisco StadiumVision Director Release 2.4 with
small differences in the user interface for that release.
For information about accessing Cisco StadiumVision Director Release 3.0 and
later, see the “How to Access Cisco StadiumVision Director” task note.
© 2011-2012 Cisco Systems, Inc.
Page 3 of 7
Accessing SV Director
Cisco StadiumVision Director supports Internet Explorer version 8 (Windows) and
FireFox 3.x (Windows and Macintosh). Other browsers, including Safari and
Chrome, are not supported.
1. Open a browser window and type http://ipaddress:8080/StadiumVision/
where ipaddress is the IP Address of the SV Director Server.
2. Enter your SV Director administrator credentials. The very first time you log in to
SV Director, use the following credentials:
Username: admin
Password: default
You will need to change the default password the first time you log in. The
“admin” username cannot be changed or deleted.
Figure 1.
Logging in to SV Director
3. Click Control Panel on the Main screen.
© 2011-2012 Cisco Systems, Inc.
Page 4 of 7
Figure 2.
StadiumVision Director Main Window
4. Wait a few moments while Cisco StadiumVision Director loads resources. When
complete, the Cisco StadiumVision Director Control Panel Setup screen displays
in a separate window. When you log in as admin, the User Management tab
displays (Figure 3).
When you log in to Cisco StadiumVision Director, the Main window remains open
so that you can run other applications without having to log out.
Figure 3.
Control Panel User Management Tab
Changing Your Cisco StadiumVision Director Password
The very first time you log in to Cisco StadiumVision Director as admin, you must
change your admin password as follows.
1. On the Setup screen, select admin, click in the password field and type a new
password. An asterisk will display next to the admin entry in the User List.
© 2011-2012 Cisco Systems, Inc.
Page 5 of 7
2. Type your email address in the Email ID field.
Figure 4.
Changing the Admin Password
3. Click Update. A status message will display in the lower left corner of the screen
to indicate your new password is being added to the Cisco StadiumVision
Director database:
4. Verify that you can log in with your new password by logging out and logging
back in to Cisco StadiumVision Director.
Logging Out of Cisco StadiumVision Director
1. Click Logout at the top right corner of the Control Panel or go to the Cisco
StadiumVision Director Main screen and click Log Out. A message displays
when you have been successfully logged out.
2. Close the Cisco StadiumVision Director window to remove this instance of Cisco
StadiumVision Director. Otherwise, click the Reset button and log back in to
Cisco StadiumVision Director.
© 2011-2012 Cisco Systems, Inc.
Page 6 of 7
Figure 5.
Logging Out of Cisco StadiumVision Director
Assigning Login Credentials for Role Based Access
Control
StadiumVision administrators can assign login credentials to different “roles” and
users of Cisco StadiumVision Director, limiting access to certain screens and Cisco
StadiumVision Director applications. This ensures that each user has access only to
the portions of the system for which they are trained and authorized to handle.
For details on how to create users and assign roles to users, see the Role Based
Access Control feature note.
© 2011-2012 Cisco Systems, Inc.
Page 7 of 7